|
|
|
| EFFECTS OF HEAT TREATMENT PROCESS ON THE MICROSTRUCTURE AND PROPERTIES OF A NEW CAST NICKEL-BASED SUPERALLOY |
| YANG Jinxia1, LI Jinguo1, WANG Meng1, WANG Yanhui2,JIN Tao1, SUN Xiaofeng1
|
1. Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016
2. Liming Aeroengine Company, Shenyang 110043 |
|
Cite this article:
YANG Jinxia , LI Jinguo, WANG Meng, WANG Yanhui,JIN Tao, SUN Xiaofeng. EFFECTS OF HEAT TREATMENT PROCESS ON THE MICROSTRUCTURE AND PROPERTIES OF A NEW CAST NICKEL-BASED SUPERALLOY. Acta Metall Sin, 2012, 48(6): 654-660.
|
|
|
Abstract A new casting Ni-based superalloy is used in industrial and aircraft turbine because of its high strength and excellent hot corrosion resistance at high temperatures (about 900 ℃). The effect of heat treatment process on its microstructure and mechanical properties of the experimental casting Ni--based superalloy was studied in the present investigation in order to improve its application level. The results showed that the stress--rupture lives were changed with the increase of heat treatment temperatures. After solution treated for 2 h, then cooling by air cooling, the stress-rupture life under the conditions of 760 ℃ and 660 MPa was the highest in the case of heat treatment temperature at 1220 ℃, while under the testing conditions of 980 ℃ and 180 MPa the stress--rupture life was the highest in the case of heat treatment temperature at 1180 ℃. The stress--rupture life decreased when being heat-treated at temperatures above 1220 or 1180 ℃. The tensile strength of the alloy was improved with the increase of heat treatment temperatures from 1120 to 1220 ℃, and was decreased in the case of heat treatment temperature at 1240 ℃. The experimental results also showed that with the increment of holding time from 2 to 8 h at 1120 ℃ the stress--rupture life increased under the conditions of 760 ℃ and 660 MPa, while it was decreased under the conditions of 980 ℃ and 180 MPa. It was found that the tensile strength was higher for the alloy being held for 2 and 4 h than that for the alloy being held for 6 and 8 h, and the stress--rupture lives changed with the different cooling ways. The mechanical properties of the alloy may be determined by the size, shape, distribution and volume fractions of γ' phase and γ/γ' eutectic.
|
|
Received: 13 February 2012
|
| [1] Yin F S. PhD Thesis, Institute of Metal Research,Chinese Academy of Sciences, Shenyang, 2003 (殷凤仕. 中国科学院金属研究所博士学位论文, 沈阳, 2003)[2] Yang J X. PhD Thesis, Institute of Metal Research,Chinese Academy of Sciences, Shenyang, 2006 (杨金侠. 中国科学院金属研究所博士学位论文, 沈阳, 2006)[3] Jackson M P, Reed R C. Mater Sci Eng, 1999; A259: 85[4] Caron P, Khan T. Mater Sci Eng, 1983; 61: 173[5] Footner P K, Richards B P. J Mater Sci, 1982; 17: 2141[6] Baladan A. J Mater Sci, 2002; 37: 2379[7] Balikci E, Raman A, Mirshams R A. Metall Mater Trans,1997; 28A: 1993[8] Monajati H, Jahazi M, Bahrami R, Yue S. Mater Sci Eng,2004; A373: 286[9] Jena J A. Mater Sci Eng, 1984; 19: 3121[10] Ges A, Fornaro O, Palacio H. J Mater Sci, 1997; 32: 3687[11] Yang J X, Zheng Q, Sun X F, Guan H R, Hu Z Q. Mater Sci Eng,2006; A429: 341[12] Yang J X, Zheng Q, Sun X F, Guan H R, Hu Z Q. J Mater Sci,2006; 41: 6476[13] Yang J X, Zheng Q, Zhang H Y, Sun X F, Guan H R, Hu Z Q. Mater Sci Eng, 2010; A527: 1016[14] Yang J X, Zheng Q, Ji M Q, Sun X F, Guan H R, Hu Z Q. Mater Sci Eng, 2011; A528: 1534[15] Yang J X, Zheng Q, Sun X F, Guan H R, Hu Z Q. Mater Sic Eng,2007; A465: 100[16] Jia Y X. PhD Thesis, Institute of Metal Research,Chinese Academy of Sciences, Shenyang, 2009 (贾玉贤. 中国科学院金属研究所博士学位论文, 沈阳, 2009)[17] Liu L R. PhD Thesis, Institute of Metal Research,Chinese Academy of Sciences, Shenyang, 2004 (刘丽荣. 中国科学院金属研究所博士学位论文, 沈阳, 2004) |
| No Suggested Reading articles found! |
|
|
Viewed |
|
|
|
Full text
|
|
|
|
|
Abstract
|
|
|
|
|
Cited |
|
|
|
|
| |
Shared |
|
|
|
|
| |
Discussed |
|
|
|
|
