Please wait a minute...
金属学报  2011, Vol. 47 Issue (4): 497-501    DOI: 10.3724/SP.J.1037.2010.00714
  论文 本期目录 | 过刊浏览 |
SiC长纤维表面(Al+Al2O3)复合涂层的制备
张露, 石南林, 宫骏, 裴志亮, 高立军, 孙超
中国科学院金属研究所, 沈阳 110016
PREPARATION OF COMPOSITE COATING (Al+Al2O3) ON SiC LONG FIBER
ZHANG Lu, SHI Nanlin, GONG Jun, PEI Zhiliang, GAO Lijun, SUN Chao
Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016
引用本文:

张露 石南林 宫骏 裴志亮 高立军 孙超. SiC长纤维表面(Al+Al2O3)复合涂层的制备[J]. 金属学报, 2011, 47(4): 497-501.
, , , , , . PREPARATION OF COMPOSITE COATING (Al+Al2O3) ON SiC LONG FIBER[J]. Acta Metall Sin, 2011, 47(4): 497-501.

全文: PDF(717 KB)  
摘要: 利用反应磁控溅射法在SiC长纤维表面沉积了(Al+Al2O3)扩散阻挡涂层, 研究了沉积工艺参数对涂层的成分、沉积速率的影响, 以及涂层对SiC纤维的表面残余应力及力学性能的影响. 结果表明, 随着溅射功率的增加, Al2O3涂层的沉积速率先迅速增加后缓慢增加; 随着工作气压的增加, Al2O3涂层的沉积速率先缓慢降低, 在工作气压到达一定值时, 沉积速率快速下降随后缓慢下降. 沉积的(Al+Al2O3)复合涂层保护了SiC纤维的富C层, 起到了保证纤维与Al2O3涂层之间结合力的作用; 激光Raman谱显示改性后纤维的表面残余应力有降低趋势. 室温和高温处理后复合丝的拉伸强度分别是计算值的97.69%和98.77%, 涂层对纤维的力学性能影响很小.
关键词 : SiC纤维,  反应磁控溅射,  扩散阻挡层,  复合涂层,  残余应力    
Abstract:Reactive magnetron sputtering was used to prepare (Al+Al2O3) diffusion barrier layer on SiC fiber surface. The relationships between deposition process parameters with composition and deposition rate of the coating, and the influence of the coating on mechanical property of SiC fiber were measured. Results show that with increasing sputtering power, the deposition rate increases rapidly at first and then slowly. With increasing of working pressure, the deposition rate of the coating deceases slowly at first, and then sharply at a typical value of working pressure, finally drops gradually. (Al+Al2O3) protected C-rich layer of SiC fiber, and improved the adherence between fiber and diffusion barrier layer. Results of laser Raman spectrum show that the coating has little influence on surface residual stress of SiC fiber. The measured tensile strength of the composite fibers is 97.69% of the calculated tensile strength according to meaning rule, and is 98.77% of the calculated one for the fiber after vacuum treatment at 850 ℃ for 10 h, meaning that (Al+Al$_{2}$O$_{3}$) coating has not much influence on mechanical property of SiC fiber.
Key words: SiC fiber    reactive magnetron sputtering    diffusion barrier layer    composite coating    residual stress
收稿日期: 2010-12-31     
作者简介: 张露, 女, 1983年生, 博士生
[1] Mileiko S T, Kiiko V M, Kolchin A A, Serebryakov A V, Korzhov V P, Starostin M Y, Sarkissyan N S. Compos Sci Technol, 2002; 62: 167

[2] Yu Y X, Cao F, Li X D. Acta Mater Compos Sin, 2004; 21(5): 79

(余煜玺, 曹峰, 李效东. 复合材料学报, 2004; 21(5): 79)

[3] Schiepers R C J, Van Loo F J J, De With G. J Am Ceram Soc, 1988; 71: 284

[4] Tang W M, Zheng Z X, Ding H F, Jin Z H. J Chin Ceram Soc, 2003; 31: 283

(汤文明, 郑治祥, 丁厚福, 金志浩. 硅酸盐学报, 2003; 31: 283)

[5] Wang Y Q, Zhou B L. Composites, 1996; 27A: 1139

[6] Lin H T, Shi N L, Sun C, Gong J, Sun X D. Acta Metall Sin, 2007; 4: 444

(林海涛, 石南林, 孙 超, 宫骏, 孙旭东. 金属学报, 2007; 4: 444)

[7] King D E, Swartz W E Jr. J Chem Educ, 1987; 64: 981

[8] Carney T J, Tsakiropoulos P, Watts J F, Castle J E. Int J Rapid Sol, 1990; 5: 189

[9] Paparazzo E. Appl Surf Sci, 1986; 25: 1

[10] Olefjord I, Mathieu H J, Marcus P. Surf Interface Anal, 1990; 15: 681

[11] Kishi K, Ikeda S. Bull Chem Soc Jpn, 1973; 46: 341

[12] Turner N H, Single A M. Surf Interface Anal, 1990; 15: 215

[13] Rastogi R S, Pourrezaei K. J Mater Process Technol, 1994; 43: 89

[14] Han Y W, Li D M, Zhao Z C, Yan G Y. Thin Film Sci Technol, 1990; 3(2): 20

(韩耀文, 李大明, 赵志成, 燕广远. 薄膜科学与技术, 1990; 3(2): 20)

[15] Liu G X, Jin Z Z,Wang Y J. Mater Sci Prog, 1991; 5: 498

(刘桂新, 金宗哲, 王延籍. 材料科学进展, 1991; 5: 498)

[16] Zhu W L, Zhu J L, Nishino S, Pezzotti G. Appl Surf Sci, 2006; 252: 2346

[17] Shackelford J F, Alexander W. CRC Materials Science and Engineering Handbook. 3rd ed. Florida: CRC press, 2001: 406
[1] 毕中南, 秦海龙, 刘沛, 史松宜, 谢锦丽, 张继. 高温合金锻件残余应力量化表征及控制技术研究进展[J]. 金属学报, 2023, 59(9): 1144-1158.
[2] 杜金辉, 毕中南, 曲敬龙. 三联冶炼GH4169合金研究进展[J]. 金属学报, 2023, 59(9): 1159-1172.
[3] 李时磊, 李阳, 王友康, 王胜杰, 何伦华, 孙光爱, 肖体乔, 王沿东. 基于中子与同步辐射技术的工程材料/部件多尺度残余应力评价[J]. 金属学报, 2023, 59(8): 1001-1014.
[4] 王重阳, 韩世伟, 谢峰, 胡龙, 邓德安. 固态相变和软化效应对超高强钢焊接残余应力的影响[J]. 金属学报, 2023, 59(12): 1613-1623.
[5] 张开元, 董文超, 赵栋, 李世键, 陆善平. 固态相变对Fe-Co-Ni超高强度钢长臂梁构件焊接-淬火过程应力和变形的影响[J]. 金属学报, 2023, 59(12): 1633-1643.
[6] 卢海飞, 吕继铭, 罗开玉, 鲁金忠. 激光热力交互增材制造Ti6Al4V合金的组织及力学性能[J]. 金属学报, 2023, 59(1): 125-135.
[7] 吴进, 杨杰, 陈浩峰. 纳入残余应力时不同拘束下DMWJ的断裂行为[J]. 金属学报, 2022, 58(7): 956-964.
[8] 张新房, 向思奇, 易坤, 郭敬东. 脉冲电流调控金属固体中的残余应力[J]. 金属学报, 2022, 58(5): 581-598.
[9] 苏凯新, 张继旺, 张艳斌, 闫涛, 李行, 纪东东. 微弧氧化6082-T6铝合金的高周疲劳性能及残余应力松弛机理[J]. 金属学报, 2022, 58(3): 334-344.
[10] 骆文泽, 胡龙, 邓德安. SUS316不锈钢马鞍形管-管接头的残余应力数值模拟及高效计算方法开发[J]. 金属学报, 2022, 58(10): 1334-1348.
[11] 李文亚, 张正茂, 徐雅欣, 宋志国, 殷硕. 冷喷涂Ni及镍基复合涂层研究进展[J]. 金属学报, 2022, 58(1): 1-16.
[12] 王文权, 杜明, 张新戈, 耿铭章. H13钢表面电火花沉积WC-Ni基金属陶瓷涂层微观组织及摩擦磨损性能[J]. 金属学报, 2021, 57(8): 1048-1056.
[13] 李索, 陈维奇, 胡龙, 邓德安. 加工硬化和退火软化效应对316不锈钢厚壁管-管对接接头残余应力计算精度的影响[J]. 金属学报, 2021, 57(12): 1653-1666.
[14] 王超, 张旭, 王玉敏, 杨青, 杨丽娜, 张国兴, 吴颖, 孔旭, 杨锐. SiCf/Ti65复合材料界面反应与基体相变机理[J]. 金属学报, 2020, 56(9): 1275-1285.
[15] 武玉鹏, 张博, 李经明, 张双楠, 吴颖, 王玉敏, 蔡桂喜. 航空发动机整体叶环中纤维断丝超声检测方法[J]. 金属学报, 2020, 56(8): 1175-1184.