Please wait a minute...
金属学报  2008, Vol. 44 Issue (10): 1209-1212     
  论文 本期目录 | 过刊浏览 |
中间退火温度对多道次冷轧Al-Mg-Sc-Zr合金力学性能的影响
杜刚;闫德胜;戎利建
中国科学院金属研究所特殊环境材料研究部
Influence of intermediate annealing temperature on strength of repeat cold-rolled Al-Mg-Sc-Zr alloy
Gang Du;Desheng Yan;
中国科学院金属研究所特殊环境材料研究部
引用本文:

杜刚; 闫德胜; 戎利建 . 中间退火温度对多道次冷轧Al-Mg-Sc-Zr合金力学性能的影响[J]. 金属学报, 2008, 44(10): 1209-1212 .
, , . Influence of intermediate annealing temperature on strength of repeat cold-rolled Al-Mg-Sc-Zr alloy[J]. Acta Metall Sin, 2008, 44(10): 1209-1212 .

全文: PDF(3420 KB)  
摘要: 研究了中间退火温度对多道次冷轧Al-Mg-Sc-Zr合金力学性能的影响.结果表明: 在各道次轧制前采用 400 ℃/ 1 h中间退火, 合金强度无明显变化;采用450 ℃/1 h中间退火, 合金强度随加工次数增加而明显降低. 对其机理分析表明, 冷变形产生的高密度位错等缺陷在较高温度的中间退火过程中为Sc和Zr原子提供了快速扩散的通道, 促进了Al3(Sc, Zr)相颗粒的粗化. Al3(Sc, Zr)颗粒的粗化不但使其阻碍位错运动的能力降低, 而且还削弱了其对回复进程的抑制作用.两种因素的共同作用导致了退火态合金强度的下降.
关键词 Al-Mg-Sc-Zr合金冷轧力学性能    
Abstract:Influence of intermediate annealing temperature on strength of repeat cold -rolled Al-Mg-Sc-Zr alloy was studied. It was found that intermediate annealing at 400℃ has no obvious effect on the strength of the alloy, while it decreases with the rolling times,especially for yield stress, when 450℃ intermediate annealing was applied. High density of dislocations induced by cold rolling will provide fast diffusion channel for Sc and Zr atoms and promot the coarsening of the Al3(Sc, Zr) particles when samples were annealed at 450℃. As a result, Al3(Sc, Zr) particles had weak ability to hinder the movement of dislocations and recovery process of alloy, and the strength of the alloy were decreased.
Key wordsintermediate annealing    Al3(Sc    Zr)    fast diffusion channel    misfit strains
收稿日期: 2008-01-22     
ZTFLH:  TG113.25  
[1]Tang M J,Ji Z S,Lu X Y.Light Alloy Fabr Technol,2004; 32(7):1 (唐明君,吉泽升.吕新宇.轻合金加工技术,2004;32(7):1)
[2]Gabriel M N,Alan J A.Mater Sci Eng,2001;A318:144
[3]Miura Y,Shioyama T,Hara D.Mater Sci Forum,1996; 217-222:505
[4]Dougherty L M,Robertson I M,Vetrano J S.Acta Mater, 2003;51:4367
[5]Ashby M F,Brown L M.Philos Mag,1963;8A:1083
[6]Royset J,Ryum N.Int Mater Rev,2005;50:19
[7]Huang Q Y,Li H K.Superalloy.Beijing:Metallurgical Industry Press,2000:22 (黄乾尧,李汉康.高温合金.北京:冶金工业出版社,2000:22)
[8]Shi D K.Dislocation and Strength of Metals.Xi'an:Xi'an Jiaotong University Press,1998:137 (石德科.位错与材料强度西安:西安交通大学出版社,1998:137)
[9]Zhao W T,Yan D S,Rong L J.Trans Nonferrous Metals Soc China,2006;16:175
[10]Alan J A.Acta Metall,1967;15:1775
[11]Marquis E A,Seidman D N.Acta Mater,2001;49:1909
[12]Sun Z Y,Liu C M.Diffusion and Phase Transformation in Alloys.Shenyang:Northeastern University Press,2002: 137 (孙振岩,刘春明.合金中的扩散与相变.沈阳:东北大学出版社,2002:137)
[13]Pan J S,Tong J M,Tian M B.Foundation of Material Science.Beijing:Tsinghua University Press,1998:465 (潘金生,仝健民,田民波.材料科学基础.北京:清华大学出版社,1998:465)
[14]Iwamura S,Miura Y.Acta Mater,2004;52:591
[1] 宫声凯, 刘原, 耿粒伦, 茹毅, 赵文月, 裴延玲, 李树索. 涂层/高温合金界面行为及调控研究进展[J]. 金属学报, 2023, 59(9): 1097-1108.
[2] 张健, 王莉, 谢光, 王栋, 申健, 卢玉章, 黄亚奇, 李亚微. 镍基单晶高温合金的研发进展[J]. 金属学报, 2023, 59(9): 1109-1124.
[3] 郑亮, 张强, 李周, 张国庆. /降氧过程对高温合金粉末表面特性和合金性能的影响:粉末存储到脱气处理[J]. 金属学报, 2023, 59(9): 1265-1278.
[4] 张雷雷, 陈晶阳, 汤鑫, 肖程波, 张明军, 杨卿. K439B铸造高温合金800℃长期时效组织与性能演变[J]. 金属学报, 2023, 59(9): 1253-1264.
[5] 陈礼清, 李兴, 赵阳, 王帅, 冯阳. 结构功能一体化高锰减振钢研究发展概况[J]. 金属学报, 2023, 59(8): 1015-1026.
[6] 丁桦, 张宇, 蔡明晖, 唐正友. 奥氏体基Fe-Mn-Al-C轻质钢的研究进展[J]. 金属学报, 2023, 59(8): 1027-1041.
[7] 李景仁, 谢东升, 张栋栋, 谢红波, 潘虎成, 任玉平, 秦高梧. 新型低合金化高强Mg-0.2Ce-0.2Ca合金挤压过程中的组织演变机理[J]. 金属学报, 2023, 59(8): 1087-1096.
[8] 袁江淮, 王振玉, 马冠水, 周广学, 程晓英, 汪爱英. Cr2AlC涂层相结构演变对力学性能的影响[J]. 金属学报, 2023, 59(7): 961-968.
[9] 王周头, 袁清, 张庆枭, 刘升, 徐光. 冷轧中碳梯度马氏体钢的组织与力学性能[J]. 金属学报, 2023, 59(6): 821-828.
[10] 吴东江, 刘德华, 张子傲, 张逸伦, 牛方勇, 马广义. 电弧增材制造2024铝合金的微观组织与力学性能[J]. 金属学报, 2023, 59(6): 767-776.
[11] 张东阳, 张钧, 李述军, 任德春, 马英杰, 杨锐. 热处理对选区激光熔化Ti55531合金多孔材料力学性能的影响[J]. 金属学报, 2023, 59(5): 647-656.
[12] 侯娟, 代斌斌, 闵师领, 刘慧, 蒋梦蕾, 杨帆. 尺寸设计对选区激光熔化304L不锈钢显微组织与性能的影响[J]. 金属学报, 2023, 59(5): 623-635.
[13] 王长胜, 付华栋, 张洪涛, 谢建新. 冷轧变形对高性能Cu-Ni-Si合金组织性能与析出行为的影响[J]. 金属学报, 2023, 59(5): 585-598.
[14] 刘满平, 薛周磊, 彭振, 陈昱林, 丁立鹏, 贾志宏. 后时效对超细晶6061铝合金微观结构与力学性能的影响[J]. 金属学报, 2023, 59(5): 657-667.
[15] 李述军, 侯文韬, 郝玉琳, 杨锐. 3D打印医用钛合金多孔材料力学性能研究进展[J]. 金属学报, 2023, 59(4): 478-488.