INFLUENCE OF DOPING WITH Si AND Y ON STRUCTURE AND PROPERTIES OF (Ti, Al)N COATING

doi:10.3724/SP.J.1037.2011.00292

Acta Metall Sin

2012, Vol. 48

Issue (1): 99-106 DOI: 10.3724/SP.J.1037.2011.00292

论文

Current Issue | Archive | Adv Search

INFLUENCE OF DOPING WITH Si AND Y ON STRUCTURE AND PROPERTIES OF (Ti, Al)N COATING

FAN Yongzhong, ZHANG Shujuan, TU Jinwei, SUN Xia, LIU Fang, LI Mingsheng

Jiangxi Key Laboratory of Surface Engineering, Jiangxi Science and Technology Normal University, Nanchang 330013

Cite this article:

FAN Yongzhong ZHANG Shujuan TU Jinwei SUN Xia LIU Fang LI Mingsheng. INFLUENCE OF DOPING WITH Si AND Y ON STRUCTURE AND PROPERTIES OF (Ti, Al)N COATING. Acta Metall Sin, 2012, 48(1): 99-106.

Download:

PDF(3603KB)
Export: BibTeX | EndNote (RIS)

Abstract Composite metastable Ti_0.3Al_0.7N and Ti_0.39Al_0.55Si_0.05Y_0.01NN hard coatings were deposited on a wrought martensite steel 1Cr11Ni2W2MoV for aero-engine compressor blades by the magnetron sputtering system with the bias voltage of 0 and -100 V respectively. Detailed microstructure, chemical composition, crystal structure, hardness and adhesion were examined by means of FESEM, EDS, XRD, Micro hardness tester and scratch tester. The influence of doping with Si and Y and bias on structure, oxidation-resistance and mechanical properties of (Ti, Al)N coatings were investigated. Pulsed bias and the doping with Si and Y gave rise to the change of phase structure and improvement of density. Doping with small amounts of Si and Y into (Ti, Al)N significantly improved the oxidation resistance at 950 ℃. The oxidation-resistance of (Ti, Al, Si, Y)N is based on the formation of dense protective Al₂O₃ layer. The application of negative pulse led to decreased hardness for (Ti, Al)N while remarkable decrease of hardness for (Ti, Al, Si, Y)N. For (Ti, Al, Si, Y)N prepared under -100 V\linebreak bias, annealing 10 h at 950 ℃ slightly decreased it's hardness because of the formation of B4 structure. And for which deposited at 0 V bias, heat-treatment of 950 ℃ for 10 h improved the hardness from 26 GPa to 35 GPa. The hardness change of the coating may be ascribed the transition of B1 phase structure. Scratch tests show that the continuous spall is not occurred for all the coatings under the critical load of 50 N.

Key words: magnetron sputtering (Ti, Al)N doping with Si and Y oxidation-resistance hardness adhesion

Received: 09 May 2011

Fund:

Supported by Scientific Research Fund of Jiangxi Provincial Education Department (No.GJJ12586)

	Service

	E-mail this article
	Add to citation manager
	E-mail Alert
	RSS
	Collect articles（0）
	Articles by authors
	FAN Yong-Zhong
	ZHANG Shu-Juan
	CHU Jin-Wei
	XUN Xia
	LIU Fang
	LI Meng-Sheng

URL:

https://www.ams.org.cn/EN/10.3724/SP.J.1037.2011.00292 OR https://www.ams.org.cn/EN/Y2012/V48/I1/99

[1] Paldey S, Deevi S C. Mater Sci Eng, 2003; A3: 58

[2] Mayrhofer P H, Mitterer C, Hultman L, Clemens H. Prog Mater Sci, 2006; 51: 1032

[3] Ma S L, Jie W Q, Xu K W. Chin J Vac Sci Technol, 2002; 22: 438

(马胜利, 介万奇, 徐可为. 真空科学与技术学报, 2002; 22: 438)

[4] Inoue S, Uchida H, Yoshinaga Y, Koterazawa K. Thin Solid Films, 1997; 300: 171

[5] Li M S, Wang F H, Wang T G, Gong J, Sun C, Wen L S. Acta Metall Sin, 2003; 39: 55

(李明升, 王福会, 王铁钢, 宫俊, 孙超, 闻立时. 金属学报, 2003; 39: 55)

[6] Makino Y. Surf Coat Technol, 2005; 193: 185

[7] Pilloud D, Pierson J F, Marco de Lucas M C, Cavaleiro A. Surf Coat Technol, 2008; 202: 2413

[8] Veprek S, Reiprich S, Shizi L. Appl Phys Lett, 1995; 66: 2640

[9] Vaz F, Rebouta L, Andritschky M, Silva M, Soares J C. Surf Coat Technol, 1998; 98: 912

[10] Pfeiler M, Zechner J, Penoy M, Michotte C, Mitterer C, Kathrein M. Surf Coat Technol, 2009; 203: 3104

[11] Lembke M I, Lewis D B, M¨unz W D, Titchmarsh J M. Surf Eng, 2001; 17: 153

[12] Li M S, Feng C J, Wang F H. Funct Mater (suppl), 2007; (38): 2615

(李明升, 冯长杰, 王福会. 功能材料(增刊), 2007; (38): 2615)

[13] Mao Y F, Tang W G, Liu J L, Han P G. Tool Eng, 2006; 40: 20

(毛延发, 唐为国, 刘金良, 韩培刚. 工具技术, 2006; 40: 20)

[14] Jung H G, Kim K Y. Oxid Met, 1998; 49: 403

[15] Flink A, Andersson J M, Alling B, Daniel R, Sjolen J, Karlsson L, Hultman L. Thin Solid Films, 2008; 517: 714

[16] Carvalho S, Rebouta L, Ribeiro E, Vaz F, Tavares C J, Alves E, Barradas N P, Riviere J P. Vacuum, 2009; 83: 1206

[17] Vennemann A, Stock H R, Kohlscheen J, Rambadt S, Erkens G. Surf Coat Technol, 2003; 174–175: 408

[18] Wang F Z, Ma W C. Vapor Deposition Applications Technology. Beijing: China Machine Press, 2006: 291

(王福贞, 马文存. 气相沉积应用技术. 北京: 机械工业出版社, 2006: 291)

[19] Makino Y. Mater Sci Eng, 1995; 2: 67

[20] Vaz F, Rebouta L, Andritschky M, Silva M, Soares J C. J Eur Ceram Soc, 1997; 17: 1971

[21] Banakh O, Schmid P E, Sanjines R, Levy F. Surf Coat Technol, 2003; 163: 57

[22] Chang Y Y, Hsiao C Y. Surf Coat Technol, 2009; 204: 992

[23] M¨unz W D. Werkst Korros, 1990; 41: 753

[24] Veprek S, Sarott F A, Iqbal Z. Phys Rev, 1987; B36: 3344

[25] Veprek S, Maritza G J, Veprek H, Karvankova P, Prochazka J. Thin Solid Films, 2005; 476: 1

[26] Raveh A, Zukerman I, Shneck R, Avni R, Fried I. Surf Coat Technol, 2007; 201: 6136

[27] Tanaka Y, Ichimiya N, Onishi Y, Yamada Y. Surf Coat Technol, 2001; 146–147: 215

[28] Carvalho S, Rebouta L, Cavaleiro A, Rocha L A, Gomes J, Alves E. Thin Solid Films, 2001; 398–399: 391

[1]	HUANG Ding, QIAO Yanxin, YANG Lanlan, WANG Jinlong, CHEN Minghui, ZHU Shenglong, WANG Fuhui. Effect of Shot Peening of Substrate Surface on Cyclic Oxidation Behavior of Sputtered Nanocrystalline Coating[J]. 金属学报, 2023, 59(5): 668-678.
[2]	WANG Haifeng, ZHANG Zhiming, NIU Yunsong, YANG Yange, DONG Zhihong, ZHU Shenglong, YU Liangmin, WANG Fuhui. Effect of Pre-Oxidation on Microstructure and Wear Resistance of Titanium Alloy by Low Temperature Plasma Oxynitriding[J]. 金属学报, 2023, 59(10): 1355-1364.
[3]	LIANG Chen, WANG Xiaojuan, WANG Haipeng. Formation Mechanism of B2 Phase and Micro-Mechanical Property of Rapidly Solidified Ti-Al-Nb Alloy[J]. 金属学报, 2022, 58(9): 1169-1178.
[4]	WANG Tao, LONG Dijun, YU Liming, LIU Yongchang, LI Huijun, WANG Zumin. Microstructure and Mechanical Properties of 14Cr-ODS Steel Fabricated by Ultra-High Pressure Sintering[J]. 金属学报, 2022, 58(2): 184-192.
[5]	XIANG Zhaolong, ZHANG Lin, XIN Yan, AN Bailing, NIU Rongmei, LU Jun, MARDANI Masoud, HAN Ke, WANG Engang. Effect of Cr Content on Microstructure of Spinodal Decomposition and Properties in FeCrCoSi Permanent Magnet Alloy[J]. 金属学报, 2022, 58(1): 103-113.
[6]	HU Long, WANG Yifeng, LI Suo, ZHANG Chaohua, DENG Dean. Study on Computational Prediction About Microstructure and Hardness of Q345 Steel Welded Joint Based on SH-CCT Diagram[J]. 金属学报, 2021, 57(8): 1073-1086.
[7]	CAO Qingping, LV Linbo, WANG Xiaodong, JIANG Jianzhong. Magnetron Sputtering Metal Glass Film Preparation and the “Specimen Size Effect” of the Mechanical Property[J]. 金属学报, 2021, 57(4): 473-490.
[8]	TONG Wenhui, ZHANG Xinyuan, LI Weixuan, LIU Yukun, LI Yan, GUO Xuming. Effect of Laser Process Parameters on the Microstructure and Properties of TiC Reinforced Co-Based Alloy Laser Cladding Layer[J]. 金属学报, 2020, 56(9): 1265-1274.
[9]	ZHANG Lin, GUO Xiao, GAO Jianwen, DENG Anyuan, WANG Engang. Effect of Electromagnetic Stirring on Microstructure and Mechanical Properties of TiB₂ Particle-Reinforced Steel[J]. 金属学报, 2020, 56(9): 1239-1246.
[10]	DENG Congkun,JIANG Hongxiang,ZHAO Jiuzhou,HE Jie,ZHAO Lei. Study on the Solidification of Ag-Ni Monotectic Alloy[J]. 金属学报, 2020, 56(2): 212-220.
[11]	LIU Yanmei, WANG Tiegang, GUO Yuyao, KE Peiling, MENG Deqiang, ZHANG Jifu. Design, Preparation and Properties of Ti-B-N Nanocomposite Coatings[J]. 金属学报, 2020, 56(11): 1521-1529.
[12]	LIU Haixia, CHEN Jinhao, CHEN Jie, LIU Guanglei. Characteristics of Waterjet Cavitation Erosion of 304 Stainless Steel After Corrosion in NaCl Solution[J]. 金属学报, 2020, 56(10): 1377-1385.
[13]	Bo LI,Zhonghua ZHANG,Huasong LIU,Ming LUO,Peng LAN,Haiyan TANG,Jiaquan ZHANG. Characteristics and Evolution of the Spot Segregations and Banded Defects in High Strength Corrosion Resistant Tube Steel[J]. 金属学报, 2019, 55(6): 762-772.
[14]	Wentao LI,Zhenyu WANG,Dong ZHANG,Jianguo PAN,Peiling KE,Aiying WANG. Preparation of Ti₂AlC Coating by the Combination of a Hybrid Cathode Arc/Magnetron Sputtering with Post-Annealing[J]. 金属学报, 2019, 55(5): 647-656.
[15]	Houpu WU,Xiubo TIAN,Xinyu ZHANG,Chunzhi GONG. Discharge Characteristics of Novel Dual-Pulse HiPIMS and Deposition of CrN Films with High Deposition Rate[J]. 金属学报, 2019, 55(3): 299-307.

No Suggested Reading articles found!

Viewed

Full text

Abstract

Cited

Shared

Discussed