Breaking the Trade-Off Relation Between Strength and Electrical Conductivity: Heterogeneous Grain Design

doi:10.11900/0412.1961.2022.00222

Acta Metall Sin

2022, Vol. 58

Issue (11): 1467-1477 DOI: 10.11900/0412.1961.2022.00222

Research paper

Current Issue | Archive | Adv Search

Breaking the Trade-Off Relation Between Strength and Electrical Conductivity: Heterogeneous Grain Design

HOU Jiapeng, SUN Pengfei, WANG Qiang, ZHANG Zhenjun, ZHANG Zhefeng(

)

Shi -changxu Innovation Center for Advanced Materials, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016, China

Cite this article:

HOU Jiapeng, SUN Pengfei, WANG Qiang, ZHANG Zhenjun, ZHANG Zhefeng. Breaking the Trade-Off Relation Between Strength and Electrical Conductivity: Heterogeneous Grain Design. Acta Metall Sin, 2022, 58(11): 1467-1477.

Download:

HTML

PDF(4110KB)
Export: BibTeX | EndNote (RIS)

Abstract

The trade-off relationship between the strength and the electrical conductivity has been the bottleneck restricting the development of conductive metallic materials with high strength and high electrical conductivity. In this study, commercially pure Al wires and commercially pure Cu wires with various grain characteristics were prepared by the cold-drawing process to investigate the influencing mechanisms of grain on strength and electrical conductivity. Surprisingly, the synchronous increase in strength and electrical conductivity may be achieved both for the commercially pure Al wires and commercially pure Cu wires in the later stage of cold-drawing deformation, which shatters the traditional constrictive relationship between the strength and the electrical conductivity. Additionally, the microstructure investigation demonstrates that with the increase of drawing deformation, the axial grains were lengthened, the radial grains were increasingly polished, and the radial <001> texture was transformed to <111> texture. Finally, the heterogeneous microstructures, including heterogeneous grain formation and heterogeneous crystal orientation were formed. The theoretical analysis reveals that the grain width and texture mainly influence the strength, and the grain length primarily influences the electrical conductivity. Consequently, the axial long grain, the radial fine grain, and radial hard orientation texture are proved to be the primary mechanisms causing the synchronous improvement of strength and electrical conductivity of commercially pure Al wires and commercially pure Cu wires. This suggests that the heterogeneous grain design may be considered a useful method to create conductive metallic materials with high strength and high electrical conductivity.

Key words: commercially pure Al wire commercially pure Cu wire heterogeneous grain strength electrical conductivity

Received: 07 May 2022

ZTFLH:

TG356.4

Fund: National Natural Science Foundation of China(52001313);China Postdoctoral Science Foundation(2019M661151)

About author: ZHANG Zhefeng, professor, Tel: (024)23971043, E-mail: zhfzhang@imr.ac.cn

	Service

	E-mail this article
	Add to citation manager
	E-mail Alert
	RSS
	（）
	Articles by authors
	Jiapeng HOU
	Pengfei SUN
	Qiang WANG
	Zhenjun ZHANG
	Zhefeng ZHANG

URL:

https://www.ams.org.cn/EN/10.11900/0412.1961.2022.00222 OR https://www.ams.org.cn/EN/Y2022/V58/I11/1467

Fig.1 Strength-electrical conductivity curves of the commercially pure Al wire (a) and the commercially pure Cu wire (b) with various area reductions (ε)

Fig.2 TEM images of the radial sections (a-c) and the axial sections (d-f) of the commercially pure Al wires manufactured with ε = 24.6% (a, d), ε = 83.1% (b, e), and ε = 90.2% (c, f)

Fig.3 TEM images of the radial sections (a-c) and the axial sections (d-f) of the commercially pure Cu wires with ε = 0 (a, d), ε = 42.7% (b, e), and ε = 79.7% (c, f)

Fig.4 EBSD images of the radial sections (a-c) and the axial sections (d-f) of the commercially pure Al wires with ε = 24.6% (a, d), ε = 83.1% (b, e), and ε = 90.2% (c, f)

Fig.5 EBSD images of the radial sections (a-c) and the axial sections (d-f) of the commercially pure Cu wires with ε = 0 (a, d), ε = 42.7% (b, e), and ε = 79.7% (c, f) (Insets in Figs.5b and c show the locally enlarged images)

Fig.6 Evolutions of the grain width and grain length of the commercially pure Al wires (a) and the commercially pure Cu wires (b) related to ε

Fig.7 Relations between the volume fractions of texture and ε of the commercially pure Al wires (a) and the commercially pure Cu wires (b)

Fig.8 Schematic of heterogeneous grain design principle for metallic metal wire achieving high strength and high electrical conductivity

1	Hou J P, Wang Q, Yang H J, et al. Microstructure evolution and strengthening mechanisms of cold-drawn commercially pure aluminum wire [J]. Mater. Sci. Eng., 2015, A639: 103
2	Guan R G, Shen Y F, Zhao Z Y, et al. A high-strength, ductile Al-0.35Sc-0.2Zr alloy with good electrical conductivity strengthened by coherent nanosized-precipitates [J]. J. Mater. Sci. Technol., 2017, 33: 215
3	Liu L, Jiang J T, Zhang B, et al. Enhancement of strength and electrical conductivity for a dilute Al-Sc-Zr alloy via heat treatments and cold drawing [J]. J. Mater. Sci. Technol., 2019, 35: 962 doi: 10.1016/j.jmst.2018.12.023
4	Yuan W H, Liang Z Y, Zhang C Y, et al. Effects of La addition on the mechanical properties and thermal-resistant properties of Al-Mg-Si-Zr alloys based on AA 6201 [J]. Mater. Des., 2012, 34: 788 doi: 10.1016/j.matdes.2011.07.003
5	Li Y P, Xiao Z, Li Z, et al. Microstructure and properties of a novel Cu-Mg-Ca alloy with high strength and high electrical conductivity [J]. J. Alloys Compd., 2017, 723: 1162 doi: 10.1016/j.jallcom.2017.06.155
6	Ren J Q, Liang S H, Jiang Y H, et al. Research on the microstructure and properties of in situ (TiB₂-TiB)/Cu composites [J]. Acta Metall. Sin., 2019, 55: 126
	任建强, 梁淑华, 姜伊辉等. 原位(TiB₂-TiB)/Cu复合材料组织与性能研究 [J]. 金属学报, 2019, 55: 126 doi: 10.11900/0412.1961.2017.00532
7	Liu Y G, Zhang J Q, Tan Q Y, et al. Additive manufacturing of high strength copper alloy with heterogeneous grain structure through laser powder bed fusion [J]. Acta Mater., 2021, 220: 117311 doi: 10.1016/j.actamat.2021.117311
8	Li R G, Guo E Y, Chen Z N, et al. Optimization of the balance between high strength and high electrical conductivity in CuCrZr alloys through two-step cryorolling and aging [J]. J. Alloys Compd., 2019, 771: 1044 doi: 10.1016/j.jallcom.2018.09.040
9	Fu Q Q, Li B, Gao M Q, et al. Quantitative mechanisms behind the high strength and electrical conductivity of Cu-Te alloy manufactured by continuous extrusion [J]. J. Mater. Sci. Technol., 2022, 121: 9 doi: 10.1016/j.jmst.2021.12.046
10	Karabay S. Modification of AA-6201 alloy for manufacturing of high conductivity and extra high conductivity wires with property of high tensile stress after artificial aging heat treatment for all-aluminium alloy conductors [J]. Mater. Des., 2006, 27: 821 doi: 10.1016/j.matdes.2005.06.005
11	Rhee H, Whittington W R, Oppedal A L, et al. Mechanical properties of novel aluminum metal matrix metallic composites: Application to overhead conductors [J]. Mater. Des., 2015, 88: 16 doi: 10.1016/j.matdes.2015.08.109
12	Cabibbo M. Microstructure strengthening mechanisms in different equal channel angular pressed aluminum alloys [J]. Mater. Sci. Eng., 2013, A560: 413
13	Ding S X, Lee W T, Chang C P, et al. Improvement of strength of magnesium alloy processed by equal channel angular extrusion [J]. Scr. Mater., 2008, 59: 1006 doi: 10.1016/j.scriptamat.2008.07.007
14	Kim W J, Wang J Y. Microstructure of the post-ECAP aging processed 6061 Al alloys [J]. Mater. Sci. Eng., 2007, A464: 23
15	Ito Y, Horita Z. Microstructural evolution in pure aluminum processed by high-pressure torsion [J]. Mater. Sci. Eng., 2009, A503: 32
16	Kamikawa N, Huang X X, Tsuji N, et al. Strengthening mechanisms in nanostructured high-purity aluminium deformed to high strain and annealed [J]. Acta Mater., 2009, 57: 4198 doi: 10.1016/j.actamat.2009.05.017
17	Saito Y, Utsunomiya H, Tsuji N, et al. Novel ultra-high straining process for bulk materials-development of the accumulative roll-bonding (ARB) process [J]. Acta Mater., 1999, 47: 579 doi: 10.1016/S1359-6454(98)00365-6
18	Feng T L, Qiu B, Ruan X L. Coupling between phonon-phonon and phonon-impurity scattering: A critical revisit of the spectral Matthiessen's rule [J]. Phys. Rev., 2015, 92B: 235206
19	Botcharova E, Freudenberger J, Schultz L. Mechanical and electrical properties of mechanically alloyed nanocrystalline Cu-Nb alloys [J]. Acta Mater., 2006, 54: 3333 doi: 10.1016/j.actamat.2006.03.021
20	Murashkin M Y, Sabirov I, Sauvage X, et al. Nanostructured Al and Cu alloys with superior strength and electrical conductivity [J]. J. Mater. Sci., 2016, 51: 33 doi: 10.1007/s10853-015-9354-9
21	Sabirov I, Murashkin M Y, Valiev R Z. Nanostructured aluminium alloys produced by severe plastic deformation: New horizons in development [J]. Mater. Sci. Eng., 2013, A560: 1
22	Valiev R Z, Murashkin M Y, Sabirov I. A nanostructural design to produce high-strength Al alloys with enhanced electrical conductivity [J]. Scr. Mater., 2014, 76: 13 doi: 10.1016/j.scriptamat.2013.12.002
23	Murashkin M Y, Sabirov I, Medvedev A E, et al. Mechanical and electrical properties of an ultrafine grained Al-8.5wt.% RE (RE = 5.4wt.% Ce, 3.1wt.% La) alloy processed by severe plastic deformation [J]. Mater. Des., 2016, 90: 433 doi: 10.1016/j.matdes.2015.10.163
24	Murashkin M Y, Sabirov I, Kazykhanov V U, et al. Enhanced mechanical properties and electrical conductivity in ultrafine-grained Al alloy processed via ECAP-PC [J]. J. Mater. Sci., 2013, 48: 4501 doi: 10.1007/s10853-013-7279-8
25	Zhu C C, Ma A B, Jiang J H, et al. Effect of ECAP combined cold working on mechanical properties and electrical conductivity of Conform-produced Cu-Mg alloys [J]. J. Alloys Compd., 2014, 582: 135 doi: 10.1016/j.jallcom.2013.08.007
26	Karabay S, Uzman I. Inoculation of transition elements by addition of AlB₂ and AlB₁₂ to decrease detrimental effect on the conductivity of 99.6% aluminium in CCL for manufacturing of conductor [J]. J. Mater. Process. Technol., 2005, 160: 174 doi: 10.1016/j.jmatprotec.2004.06.015
27	Li P F, Wu Z G, Wang Y L, et al. Effect of cerium on mechanical performance and electrical conductivity of aluminum rod for electrical purpose [J]. J. Rare Earths, 2006, 24: 355 doi: 10.1016/S1002-0721(07)60400-1
28	Cui X L, Wu Y Y, Liu X F, et al. Effects of grain refinement and boron treatment on electrical conductivity and mechanical properties of AA1070 aluminum [J]. Mater. Des., 2015, 86: 397 doi: 10.1016/j.matdes.2015.06.149
29	Liao H C, Liu Y, Lü C L, et al. Effect of Ce addition on castability, mechanical properties and electric conductivity of Al-0.3Si-0.2Mg alloy [J]. Int. J. Cast. Met. Res., 2015, 28: 213 doi: 10.1179/1743133615Y.0000000002
30	Xie M, Liu J L, Lu X Y, et al. Investigation on the Cu-Cr-RE alloys by rapid solidification [J]. Mater. Sci. Eng., 2001, A304-306: 529
31	Hou J P, Li R, Wang Q, et al. Three principles for preparing Al wire with high strength and high electrical conductivity [J]. J. Mater. Sci. Technol., 2019, 35: 742 doi: 10.1016/j.jmst.2018.11.013
32	Hou J P, Wang Q, Zhang Z J, et al. Nano-scale precipitates: The key to high strength and high conductivity in Al alloy wire [J]. Mater. Des., 2017, 132: 148 doi: 10.1016/j.matdes.2017.06.062
33	Li J Z, Ding H, Li B M, et al. Microstructure evolution and properties of a Cu-Cr-Zr alloy with high strength and high conductivity [J]. Mater. Sci. Eng., 2021, A819: 141464
34	Wang Y P, Fu R D, Li Y J, et al. A high strength and high electrical conductivity Cu-Cr-Zr alloy fabricated by cryogenic friction stir processing and subsequent annealing treatment [J]. Mater. Sci. Eng., 2019, A755: 166
35	Ye Y X, Yang X Y, Wang J, et al. Enhanced strength and electrical conductivity of Cu-Zr-B alloy by double deformation-aging process [J]. J. Alloys Compd., 2014, 615: 249 doi: 10.1016/j.jallcom.2014.07.010
36	Carlton C E, Ferreira P J. What is behind the inverse Hall-Petch effect in nanocrystalline materials? [J]. Acta Mater., 2007, 55: 3749 doi: 10.1016/j.actamat.2007.02.021
37	Hall E O. The deformation and ageing of mild steel: III Discussion of results [J]. Proc. Phys. Soc., 1951, 64B: 747
38	Wyrzykowski J W, Grabski M W. The Hall-Petch relation in aluminium and its dependence on the grain boundary structure [J]. Philos. Mag., 1986, 53A: 505
39	Miyajima Y, Komatsu S Y, Mitsuhara M, et al. Change in electrical resistivity of commercial purity aluminium severely plastic deformed [J]. Philos. Mag., 2010, 90: 4475 doi: 10.1080/14786435.2010.510453
40	Ritchie R O. The conflicts between strength and toughness [J]. Nat. Mater., 2011, 10: 817 doi: 10.1038/nmat3115 pmid: 22020005
41	Wang H W, He Z F, Jia N. Microstructure and mechanical properties of a FeMnCoCr high-entropy alloy with heterogeneous structure [J]. Acta Metall. Sin., 2021, 57: 632 doi: 10.11900/0412.1961.2020.00225
	王洪伟, 何竹风, 贾楠. 非均匀组织FeMnCoCr高熵合金的微观结构和力学性能 [J]. 金属学报, 2021, 57: 632 doi: 10.11900/0412.1961.2020.00225
42	Wu X L, Zhu Y T. Heterogeneous materials: A new class of materials with unprecedented mechanical properties [J]. Mater. Res. Lett., 2017, 5: 527 doi: 10.1080/21663831.2017.1343208
43	Zhu Y T, Wu X L. Perspective on hetero-deformation induced (HDI) hardening and back stress [J]. Mater. Res. Lett., 2019, 7: 393 doi: 10.1080/21663831.2019.1616331
44	An X H, Wu S D, Wang Z G, et al. Enhanced cyclic deformation responses of ultrafine-grained Cu and nanocrystalline Cu-Al alloys [J]. Acta Mater., 2014, 74: 200 doi: 10.1016/j.actamat.2014.04.053
45	Li P, Li S X, Wang Z G, et al. Fundamental factors on formation mechanism of dislocation arrangements in cyclically deformed fcc single crystals [J]. Prog. Mater. Sci., 2011, 56: 328 doi: 10.1016/j.pmatsci.2010.12.001
46	Wang X F, Guo M X, Luo J R, et al. Effect of intermediate annealing time on microstructure, texture and mechanical properties of Al-Mg-Si-Cu alloy [J]. Mater. Charact., 2018, 142: 309 doi: 10.1016/j.matchar.2018.05.048
47	Wang S C, Starink M J, Gao N, et al. Texture evolution by shear on two planes during ECAP of a high-strength aluminum alloy [J]. Acta Mater., 2008, 56: 3800 doi: 10.1016/j.actamat.2008.04.022
48	Zhang J Y, Ma M Y, Shen F H, et al. Influence of deformation and annealing on electrical conductivity, mechanical properties and texture of Al-Mg-Si alloy cables [J]. Mater. Sci. Eng., 2018, A710: 27
49	Hou J P, Chen Q Y, Wang Q, et al. Effects of annealing treatment on the microstructure evolution and the strength degradation behavior of the commercially pure Al conductor [J]. Mater. Sci. Eng., 2017, A707: 511
50	Hou J P, Li R, Wang Q, et al. Breaking the trade-off relation of strength and electrical conductivity in pure Al wire by controlling texture and grain boundary [J]. J. Alloys Compd., 2018, 769: 96 doi: 10.1016/j.jallcom.2018.07.358
51	Parthasarathy T A, Rao S I, Dimiduk D M, et al. Contribution to size effect of yield strength from the stochastics of dislocation source lengths in finite samples [J]. Scr. Mater., 2007, 56: 313 doi: 10.1016/j.scriptamat.2006.09.016
52	Beyerlein I J, Tóth L S. Texture evolution in equal-channel angular extrusion [J]. Prog. Mater. Sci., 2009, 54: 427 doi: 10.1016/j.pmatsci.2009.01.001
53	Bailey J E, Hirsch P B. The dislocation distribution, flow stress, and stored energy in cold-worked polycrystalline silver [J]. Philos. Mag., 1960, 5: 485 doi: 10.1080/14786436008238300
54	Hansen N, Huang X. Microstructure and flow stress of polycrystals and single crystals [J]. Acta Mater., 1998, 46: 1827 doi: 10.1016/S1359-6454(97)00365-0
55	Matthiessen A, Vogt A C C. On the influence of temperature on the electric conducting-power of alloys [J]. Philos. Trans., 1864, 154: 167
56	Murata Y, Nakaya I, Morinaga M. Assessment of strain energy by measuring dislocation density in copper and aluminium prepared by ECAP and ARB [J]. Mater. Trans., 2008, 49: 20 doi: 10.2320/matertrans.ME200707
57	Miyajima Y, Mitsuhara M, Hata S, et al. Quantification of internal dislocation density using scanning transmission electron microscopy in ultrafine grained pure aluminium fabricated by severe plastic deformation [J]. Mater. Sci. Eng., 2010, A528: 776
58	Zhang J W, Gao N, Starink M J. Microstructure development and hardening during high pressure torsion of commercially pure aluminium: Strain reversal experiments and a dislocation based model [J]. Mater. Sci. Eng., 2011, A528: 2581
59	Sauvage X, Bobruk E V, Murashkin M Y, et al. Optimization of electrical conductivity and strength combination by structure design at the nanoscale in Al-Mg-Si alloys [J]. Acta Mater., 2015, 98: 355 doi: 10.1016/j.actamat.2015.07.039

[1]	WANG Lei, LIU Mengya, LIU Yang, SONG Xiu, MENG Fanqiang. Research Progress on Surface Impact Strengthening Mechanisms and Application of Nickel-Based Superalloys[J]. 金属学报, 2023, 59(9): 1173-1189.
[2]	FENG Qiang, LU Song, LI Wendao, ZHANG Xiaorui, LI Longfei, ZOU Min, ZHUANG Xiaoli. Recent Progress in Alloy Design and Creep Mechanism of γ'-Strengthened Co-Based Superalloys[J]. 金属学报, 2023, 59(9): 1125-1143.
[3]	LI Fulin, FU Rui, BAI Yunrui, MENG Lingchao, TAN Haibing, ZHONG Yan, TIAN Wei, DU Jinhui, TIAN Zhiling. Effects of Initial Grain Size and Strengthening Phase on Thermal Deformation and Recrystallization Behavior of GH4096 Superalloy[J]. 金属学报, 2023, 59(7): 855-870.
[4]	WANG Zongpu, WANG Weiguo, Rohrer Gregory S, CHEN Song, HONG Lihua, LIN Yan, FENG Xiaozheng, REN Shuai, ZHOU Bangxin. {111}/{111} Near Singular Boundaries in an Al-Zn-Mg-Cu Alloy Recrystallized After Rolling at Different Temperatures[J]. 金属学报, 2023, 59(7): 947-960.
[5]	LIU Junpeng, CHEN Hao, ZHANG Chi, YANG Zhigang, ZHANG Yong, DAI Lanhong. Progress of Cryogenic Deformation and Strengthening-Toughening Mechanisms of High-Entropy Alloys[J]. 金属学报, 2023, 59(6): 727-743.
[6]	LIANG Kai, YAO Zhihao, XIE Xishan, YAO Kaijun, DONG Jianxin. Correlation Between Microstructure and Properties of New Heat-Resistant Alloy SP2215[J]. 金属学报, 2023, 59(6): 797-811.
[7]	WANG Bin, NIU Mengchao, WANG Wei, JIANG Tao, LUAN Junhua, YANG Ke. Microstructure and Strength-Toughness of a Cu-Contained Maraging Stainless Steel[J]. 金属学报, 2023, 59(5): 636-646.
[8]	ZHANG Zhefeng, LI Keqiang, CAI Tuo, LI Peng, ZHANG Zhenjun, LIU Rui, YANG Jinbo, ZHANG Peng. Effects of Stacking Fault Energy on the Deformation Mechanisms and Mechanical Properties of Face-Centered Cubic Metals[J]. 金属学报, 2023, 59(4): 467-477.
[9]	WAN Tao, CHENG Zhao, LU Lei. Effect of Component Proportion on Mechanical Behaviors of Laminated Nanotwinned Cu[J]. 金属学报, 2023, 59(4): 567-576.
[10]	CHENG Yuanyao, ZHAO Gang, XU Deming, MAO Xinping, LI Guangqiang. Effect of Austenitizing Temperature on Microstructures and Mechanical Properties of Si-Mn Hot-Rolled Plate After Quenching and Partitioning Treatment[J]. 金属学报, 2023, 59(3): 413-423.
[11]	LI Dou, XU Changjiang, LI Xuguang, LI Shuangming, ZHONG Hong. Thermoelectric Properties of P-Type Ce_yFe₃CoSb₁₂ Thermoelectric Materials and Coatings Doped with La[J]. 金属学报, 2023, 59(2): 237-247.
[12]	ZHU Yunpeng, QIN Jiayu, WANG Jinhui, MA Hongbin, JIN Peipeng, LI Peijie. Microstructure and Properties of AZ61 Ultra-Fine Grained Magnesium Alloy Prepared by Mechanical Milling and Powder Metallurgy Processing[J]. 金属学报, 2023, 59(2): 257-266.
[13]	WANG Chongyang, HAN Shiwei, XIE Feng, HU Long, DENG Dean. Influence of Solid-State Phase Transformation and Softening Effect on Welding Residual Stress of Ultra-High Strength Steel[J]. 金属学报, 2023, 59(12): 1613-1623.
[14]	ZHANG Kaiyuan, DONG Wenchao, ZHAO Dong, LI Shijian, LU Shanping. Effect of Solid-State Phase Transformation on Stress and Distortion for Fe-Co-Ni Ultra-High Strength Steel Components During Welding and Vacuum Gas Quenching Processes[J]. 金属学报, 2023, 59(12): 1633-1643.
[15]	YANG Lei, ZHAO Fan, JIANG Lei, XIE Jianxin. Development of Composition and Heat Treatment Process of 2000 MPa Grade Spring Steels Assisted by Machine Learning[J]. 金属学报, 2023, 59(11): 1499-1512.

No Suggested Reading articles found!

Viewed

Full text

Abstract

Cited

Shared

Discussed