Please wait a minute...
金属学报  1992, Vol. 28 Issue (4): 58-62    
  论文 本期目录 | 过刊浏览 |
Al-Li-Cu-Mg合金应力腐蚀性能及机理研究
王政富;朱自勇;柯伟;张匀;胡壮麒
中国科学院金属腐蚀与防护研究所腐蚀科学开放实验室;中国科学院金属腐蚀与防护研究所腐蚀科学开放实验室;中国科学院金属腐蚀与防护研究所腐蚀科学开放实验室;中国科学院金属研究所;中国科学院金属研究所
STRESS CORROSION PERFORMANCE OF Al-Li-Cu-Mg ALLOY
WANG Zhengfu;ZHU Ziyong;KE Wei;ZHANG Yun;HU Zhuangqi Corrosion Science Laboratory; Institute of Corrosion and Protection of Metals; Academia Sinica; Shenyang; Institue of Metal Research; Academia Sinica; Shenyang
引用本文:

王政富;朱自勇;柯伟;张匀;胡壮麒. Al-Li-Cu-Mg合金应力腐蚀性能及机理研究[J]. 金属学报, 1992, 28(4): 58-62.
, , , , . STRESS CORROSION PERFORMANCE OF Al-Li-Cu-Mg ALLOY[J]. Acta Metall Sin, 1992, 28(4): 58-62.

全文: PDF(641 KB)  
摘要: 利用恒应变速率方法研究了Al—Li—Cu—Mg合金的应力腐蚀开裂,包括时效条件及外加电位对应力腐蚀的影响,同时研究了试样表面相对氢浓度与外加电位及应力腐蚀时间的关系,实验结果表明,合金的应力腐蚀性能取决于时效条件,其中峰时效条件下最差,自然时效条件下最好,应力腐蚀敏感性及试样表面氢浓度与外加电位有关,阳极电位增加应力腐蚀敏感性,阴极电位低于临界电位时加速应力腐蚀,认为合金在应力腐蚀过程中阳极溶解与氢脆机制联合作用。
关键词 Al-Li合金应力腐蚀阳极溶解氢脆    
Abstract:Studies were made of the influence of aging conditions and applied potentials onthe stress corrosion cracking (SCC) susceptibility, for an Al-Li-Cu-Mg alloy by slow strainrate technique. The relationship between the relative hydrogen content on specimen surface andthe applied potentials and elapsed time has also been examined. The SCC susceptibility wasfound to be dependent on aging conditions in which the peak aged condition gave the worstSCC resistance and the natural aged condition had the best one. The SCC susceptibility and sur-face hydrogen content are related to the applied potentials. The anodic potentials increase SCCsusceptibility, while the cathodic ones below the critical accelerate SCC. It is considered thatboth the anodic dissolution and hydrogen embrittlement contribute to SCC.
Key wordsAl-Li alloy    stress corrosion cracking    anodic dissolution    hydrogen embrittlement
收稿日期: 1992-04-18     
1 Gray A. J Phys Colloq, 1987; 48(8) : C3-891
2 Rinker J G, Marek M, Sanders T H Jr. In: Starke E A Jr., Sanders T H Jr. eds., Aluminum-Lithium Alloys Ⅱ, Proc 2nd Int Aluminum-Lithium Conf, TMS-AIME, 1984: 597
3 Braun R, Buhl H. J Phys Colloq, 1987; 48(9) : C3-843
4 Christodulou L, Struble L, Pikens J R. In: Starke E A Jr., Sanders T H Jr. eds., Aluminum-Lithium Alloys Ⅱ, Proc 2nd Int Aluminum-Lithium Conf, TMS-AIME, 1984: 561
5 Balasubramaniam R, Duquette D J. In: Sanders T H Jr,, Starke E A Jr. eds., Aluminum-Lithium Alloys, Proc 5th Int Aluminum-Lithium Conf, Williamsburg, Virginia, March 27--31, 1989, Birmingham, UK: Materials and Component Engineering, 1989: 1271
6 Ahmad M. J Phys Colloq, 1987; 48(9) : C3-871
7 张匀,刘玉林,赵洪恩,胡壮麒,朱自勇,王政富.金属学报,1991;27:B271
8 Holroyd N J H, Gray A, Scainans G M, Heramnn R. In: Baker C, Gregson P J, Harris S J, Peel C J. Proc 3rd Int Aluminum-Lithium Conf, Oxford, UK, July, 1985, London: The Institute of Metals, 1986: 310
[1] 韩恩厚, 王俭秋. 表面状态对核电关键材料腐蚀和应力腐蚀的影响[J]. 金属学报, 2023, 59(4): 513-522.
[2] 常立涛. 压水堆主回路高温水中奥氏体不锈钢加工表面的腐蚀与应力腐蚀裂纹萌生:研究进展及展望[J]. 金属学报, 2023, 59(2): 191-204.
[3] 马志民, 邓运来, 刘佳, 刘胜胆, 刘洪雷. 淬火速率对7136铝合金应力腐蚀开裂敏感性的影响[J]. 金属学报, 2022, 58(9): 1118-1128.
[4] 王硕, 王俊升. Al-Li合金中 δ′/θ′/δ复合沉淀相结构演化及稳定性的第一性原理探究[J]. 金属学报, 2022, 58(10): 1325-1333.
[5] 肖娜, 惠卫军, 张永健, 赵晓丽. 真空渗碳处理齿轮钢的氢脆敏感性[J]. 金属学报, 2021, 57(8): 977-988.
[6] 兰亮云, 孔祥伟, 邱春林, 杜林秀. 基于多尺度力学实验的氢脆现象的最新研究进展[J]. 金属学报, 2021, 57(7): 845-859.
[7] 李师居, 李洋, 陈建强, 李中豪, 许光明, 李勇, 王昭东, 王国栋. 电磁振荡场作用下双辊铸轧制备2099Al-Li合金的偏析行为及组织性能[J]. 金属学报, 2020, 56(6): 831-839.
[8] 刘振宝,梁剑雄,苏杰,王晓辉,孙永庆,王长军,杨志勇. 高强度不锈钢的研究及发展现状[J]. 金属学报, 2020, 56(4): 549-557.
[9] 李金许,王伟,周耀,刘神光,付豪,王正,阚博. 汽车用先进高强钢的氢脆研究进展[J]. 金属学报, 2020, 56(4): 444-458.
[10] 蔡超,李煬,李劲风,张昭,张鉴清. 2A97 Al-Li合金薄板时效析出与电位及晶间腐蚀的相关性研究[J]. 金属学报, 2019, 55(8): 958-966.
[11] 李旭,杨庆波,樊祥泽,呙永林,林林,张志清. 变形参数对2195 Al-Li合金动态再结晶的影响[J]. 金属学报, 2019, 55(6): 709-719.
[12] 马宏驰, 杜翠薇, 刘智勇, 李永, 李晓刚. E690高强低合金钢焊接热影响区典型组织在含SO2海洋环境中的应力腐蚀行为对比研究[J]. 金属学报, 2019, 55(4): 469-479.
[13] 邓平,孙晨,彭群家,韩恩厚,柯伟,焦治杰. 核用304不锈钢辐照促进应力腐蚀开裂研究[J]. 金属学报, 2019, 55(3): 349-361.
[14] 张聪惠, 荣花, 宋国栋, 胡坤. 喷丸表面粗糙度对纯Ti焊接接头在HCl溶液中应力腐蚀开裂行为的影响[J]. 金属学报, 2019, 55(10): 1282-1290.
[15] 赵晓丽, 张永健, 邵成伟, 惠卫军, 董瀚. 两相区退火处理冷轧0.1C-5Mn中锰钢的氢脆敏感性[J]. 金属学报, 2018, 54(7): 1031-1041.