Please wait a minute...
金属学报  2026, Vol. 62 Issue (5): 941-958    DOI: 10.11900/0412.1961.2025.00266
  综述 本期目录 | 过刊浏览 |
高压铸造铝合金的流动性、组织特征及解析模型
熊守美1,2(), 何祖年1()
1 清华大学 材料学院 北京 100084
2 清华大学 先进成形制造教育部重点实验室 北京 100084
Fluidity, Microstructural Characteristics, and Analytical Models of High-Pressure Die-Cast Aluminum Alloys
XIONG Shoumei1,2(), HE Zunian1()
1 School of Materials Science and Engineering, Tsinghua University, Beijing 100084, China
2 Key Laboratory for Advanced Materials Processing Technology, Ministry of Education, Tsinghua University, Beijing 100084, China
引用本文:

熊守美, 何祖年. 高压铸造铝合金的流动性、组织特征及解析模型[J]. 金属学报, 2026, 62(5): 941-958.
Shoumei XIONG, Zunian HE. Fluidity, Microstructural Characteristics, and Analytical Models of High-Pressure Die-Cast Aluminum Alloys[J]. Acta Metall Sin, 2026, 62(5): 941-958.

全文: PDF(3866 KB)   HTML
摘要: 

高压铸造凭借高速充型与快速凝固的特点,已成为新能源汽车大型一体化铝合金结构件的关键成形技术。然而,在大型薄壁铸件中,熔体流动行为与组织缺陷演化之间存在复杂的耦合关系,其机理仍缺乏系统认识。本文系统综述了高压铸造铝合金流动性的研究进展,并从工艺参数、微观组织和解析模型三个方面构建统一的分析框架。首先,总结了压铸条件下流动性的影响因素,指出工艺参数和合金设计共同通过调控传热与凝固过程来改变流动性。其次,阐明了压铸件典型层状组织(皮肤层、缺陷带和外部凝固晶体)的形成机制,并指出了流动过程中枝晶网络连通、溶质富集及孔洞演化对流动终止的关键作用。最后,分析了各种流动解析模型在物理假设与预测能力方面的差异。综上,压铸流动性的本质是热-相-流三场耦合作用的结果。并指出未来需在停止流动机理、同步辐射原位表征及数据驱动方面作进一步深入研究。

关键词 : 高压铸造,  铝合金,  流动性    
Abstract:

High-pressure die casting (HPDC), characterized by high filling speeds and rapid solidification, has become a key manufacturing process for large integrated aluminum alloy structural components in electric vehicles. However, in large thin-walled castings, complex coupling exists between melt flow behavior and the evolution of microstructural defects, and the underlying mechanisms remain insufficiently understood. This paper systematically reviews recent progress in the fluidity of aluminum alloys under HPDC conditions and establishes a unified analytical framework from three perspectives: process parameters, microstructural characteristics, and analytical models. First, the factors influencing fluidity in die casting are summarized, highlighting that both processing parameters and alloy design jointly affect fluidity by regulating heat transfer and solidification processes. Second, the formation mechanisms of the characteristic layered microstructure in die castings, including the skin layer, defect band, and externally solidified crystals (ESCs), are elucidated. The critical roles of dendritic network connectivity, solute enrichment, and pore evolution in flow stoppage are also discussed. Finally, the differences among various analytical models for fluidity are compared in terms of their physical assumptions and predictive capabilities. Overall, the fluidity of die cast alloys is governed by the coupled interactions of thermal, phase transformation, and flow fields. Future research should further focus on the mechanisms of flow stoppage, in situ synchrotron characterization, and data-driven approaches.

Key words: high-pressure die casting    aluminum alloy    fluidity
收稿日期: 2025-09-09     
ZTFLH:  TG24  
基金资助:国家重点研发计划项目(2022YFB3404201)
通讯作者: 何祖年,hezn23@mails.tsinghua.edu.cn,主要从事压铸条件下合金流动性研究; 熊守美,smxiong@tsinghua.edu.cn,主要从事压铸工艺与合金设计研究
Corresponding author: HE Zunian, Tel: (010)62789448, E-mail: hezn23@mails.tsinghua.edu.cn; XIONG Shoumei, professor, Tel: (010)62773793, E-mail: smxiong@tsinghua.edu.cn
作者简介: 熊守美,男,1966年生,教授,博士
图1  压铸条件下的流动性模具试样及其有效流动长度与缺陷流动末端[32]
图2  不同工艺条件下压铸铝合金流动性测试结果[32]
图3  螺旋形压铸件流动性测试照片及流动长度结果[37]
图4  不同Si含量和工艺参数下压铸铝合金的流动性[39]
图5  AlSi10MnMg合金在不同熔体温度与充型速率下的显微组织[16]
图6  不同壁厚AlSi9MnVZr合金试样截面的显微组织[62]
图7  AlSi10MnMg压铸件断口孔洞的三维重构与显微表征[65]
图8  通过合金预处理与重力浇铸模具改装模拟压铸过程所得A356合金圆柱铸件的微观组织[54]
图9  高剪切应变区与压缩区作用下缺陷带形成示意图[67]
图10  从模具壁面至流道中心的固相分数梯度示意图[54]
图11  一维基本模型示意图
[1] Luo A A, Sachdev A K, Apelian D. Alloy development and process innovations for light metals casting [J]. J. Mater. Process. Technol., 2022, 306: 117606
doi: 10.1016/j.jmatprotec.2022.117606
[2] Jiao X Y, Liu C F, Wang J, et al. On the characterization of microstructure and fracture in a high-pressure die-casting Al-10 wt%Si alloy [J]. Prog. Nat. Sci.: Mater. Int., 2020, 30: 221
doi: 10.1016/j.pnsc.2019.04.008
[3] Wang Q G, Wang A, Coryell J. Ultra-large aluminum shape casting: Opportunities and challenges [J]. China Foundry, 2024, 21: 397
doi: 10.1007/s41230-024-4111-9
[4] Hu Q Y, Guo W B, Zhao H D. Influence of wall thickness and intensification pressure on the microstructures and mechanical properties of AlSi7-SiC composites fabricated by the vacuum-assisted HPDC process [J]. Mater. Sci. Eng., 2021, A819: 141470
[5] Wang Q L, Xiong S M. Effect of multi-step slow shot speed on microstructure of vacuum die cast AZ91D magnesium alloy [J]. Trans. Nonferrous Met. Soc. China, 2015, 25: 375
doi: 10.1016/S1003-6326(15)63613-5
[6] Liu Y X, Zhang Y F, Liu W N, et al. Enhanced mechanical properties and thermal conductivity of high-pressure die-cast AlMg6Si2MnZr alloy by controlling the externally solidified crystals [J]. J. Mater. Process. Technol., 2022, 306: 117645
doi: 10.1016/j.jmatprotec.2022.117645
[7] Jiao X Y, Liu C F, Guo Z P, et al. On the characterization of primary iron-rich phase in a high-pressure die-cast hypoeutectic Al-Si alloy [J]. J. Alloys Compd., 2021, 862: 158580
doi: 10.1016/j.jallcom.2020.158580
[8] Haga T, Imamura S, Fuse H. Fluidity investigation of pure Al and Al-Si alloys [J]. Materials, 2021, 14: 5372
doi: 10.3390/ma14185372
[9] CarlisleDucker. ATG 2023 north american light vehicle aluminum content and outlook summary report [R]. Ducker Carlisle for Aluminum Transportation Group (ATG), 2023.https://drivealuminum.org/wp-content/uploads/2023/05/Ducker-ATG-2023-Summary-Report-April-2023.pdf
[10] Li Y, Li H X, Katgerman L, et al. Recent advances in hot tearing during casting of aluminium alloys [J]. Prog. Mater. Sci., 2021, 117: 100741
doi: 10.1016/j.pmatsci.2020.100741
[11] Hu Z Q, Zhang X J, Wu S S. Microstructure, mechanical properties and die-filling behavior of high-performance die-cast Al-Mg-Si-Mn alloy [J]. Acta Metall. Sin. (Engl. Lett.), 2015, 28: 1344
doi: 10.1007/s40195-015-0332-7
[12] Niu Z C, Liu G Y, Li T, et al. Effect of high pressure die casting on the castability, defects and mechanical properties of aluminium alloys in extra-large thin-wall castings [J]. J. Mater. Process. Technol., 2022, 303: 117525
doi: 10.1016/j.jmatprotec.2022.117525
[13] Han Q. A model correlating fluidity to alloy variables in hypoeutectic alloys [J]. Acta Mater., 2022, 226: 117587
doi: 10.1016/j.actamat.2021.117587
[14] Adamane A R, Arnberg L, Fiorese E, et al. Influence of injection parameters on the porosity and tensile properties of high-pressure die cast Al-Si alloys: A review [J]. Int. J. Met., 2015, 9: 43
[15] Chavan R, Kulkarni P S. Die design and optimization of cooling channel position for cold chamber high pressure die casting machine [J]. IOP Conf. Ser.: Mater. Sci. Eng., 2020, 810:012017
[16] Jiao X Y, Wang P Y, Liu Y X, et al. Effect of shot speeds on the microstructural framework and abnormal eutectic bands in a high pressure die casting hypoeutectic AlSi10MnMg alloy [J]. J. Mater. Process. Technol., 2024, 326: 118312
doi: 10.1016/j.jmatprotec.2024.118312
[17] Đjurdjević M B, Jovanović V, Komatina M, et al. The specificity of determining the latent heat of solidification of cast hypoeutectic AlSiCu alloys using the DSC method [J]. Materials, 2024, 17: 4228
doi: 10.3390/ma17174228
[18] Flemings M C. Fluidity of metals-techniques for producing ultra-thin section castings [J]. Br. Foundrym., 1964, 57: 312
[19] Ravi K R, Pillai R M, Amaranathan K R, et al. Fluidity of aluminum alloys and composites: a review [J]. J. Alloys Compd., 2008, 456: 201
doi: 10.1016/j.jallcom.2007.02.038
[20] Han Q, Zhang J. Fluidity of alloys under high-pressure die casting conditions: Flow-choking mechanisms [J]. Metall. Mater. Trans., 2020, 51B: 1795
[21] Wang Q L, Xiong S M. Vacuum assisted high-pressure die casting of AZ91D magnesium alloy at different slow shot speeds [J]. Trans. Nonferrous Met. Soc. China, 2014, 24: 3051
doi: 10.1016/S1003-6326(14)63442-7
[22] Faura F, López J, Hernández J. On the optimum plunger acceleration law in the slow shot phase of pressure die casting machines [J]. Int. J. Mach. Tools Manuf., 2001, 41: 173
doi: 10.1016/S0890-6955(00)00079-1
[23] Ma C, Yu W, Zhang T, et al. The effect of slow shot speed and casting pressure on the 3D microstructure of high pressure die casting AE44 magnesium alloy [J]. J. Magnes. Alloy., 2023, 11: 753
doi: 10.1016/j.jma.2021.09.011
[24] Kohlstädt S, Vynnycky M, Goeke S, et al. On determining the critical velocity in the shot sleeve of a high-pressure die casting machine using open source CFD [J]. Fluids, 2021, 6: 386
doi: 10.3390/fluids6110386
[25] Hu Q, Guo W, Xiao P, et al. Effects of fast shot speed and wall thickness on the microstructures and mechanical properties of the high pressure die-casting 6061-SiC composites [J]. Metall. Mater. Trans., 2021, 52 B: 2283
[26] Dargusch M S, Hamasaiid A, Dour G, et al. The influence of in-cavity pressure on heat transfer and porosity formation during high-pressure die casting of A380 alloy [J]. JOM, 2020, 72: 3798
doi: 10.1007/s11837-020-04341-y
[27] Vossel T, Wolff N, Pustal B, et al. Influence of die temperature control on solidification and the casting process [J]. Int. J. Metalcast., 2020, 14: 907
doi: 10.1007/s40962-019-00391-4
[28] Watari H, Nishida S, Haga T, et al. Effect of casting conditions on fluidity of aluminum alloy in die casting [A]. JSME 2020 Conference on Leading Edge Manufacturing/Materials and Processing [C/OL]. American Society of Mechanical Engineers, 2020,
[29] Shaat M, Zheng Y. Fluidity and phase transitions of water in hydrophobic and hydrophilic nanotubes [J]. Sci. Rep., 2019, 9: 5689
doi: 10.1038/s41598-019-42101-4 pmid: 30952907
[30] Bai Z, Wu X. Effects of soldering and wear of die-casting die during ejection: Surface roughness and casting temperature [J]. Eng. Fail. Anal., 2023, 151: 107383
doi: 10.1016/j.engfailanal.2023.107383
[31] Brezina M, Kondic V. Flow phenomena in investment casting [J]. Br. Foundrym., 1973, 66: 337
[32] He Z N, Liu Y X, Wan A X, et al. Revealing the three-dimensional morphology and evolution mechanism of porosity at the flow end in non-heat-treated high-pressure die-cast AlSi9MnVZr alloy [J]. J. Mater. Process. Technol., 2026, 349: 119209
doi: 10.1016/j.jmatprotec.2026.119209
[33] Xie H, Wang J, Li Y, et al. Fast shot speed induced microstructure and mechanical property evolution of high pressure die casting Mg-Al-Zn-RE alloys [J]. J. Mater. Process. Technol., 2024, 331: 118523
doi: 10.1016/j.jmatprotec.2024.118523
[34] Jiao X Y, Zhang K, Peng L G, et al. Porosity evolution in a die-cast Al-Mg-Si alloy: Roles of intensification pressure and short-term aging [J]. Mater. Charact., 2026: 116005
[35] Barenji R V. Effect of reinforcement amount, mold temperature, superheat, and mold thickness on fluidity of in-situ Al-Mg2Si composites [J]. China Foundry, 2018, 15: 66
doi: 10.1007/s41230-018-7095-5
[36] Mollard F R, Flemings M C, Niyama E F. Aluminum fluidity in casting [J]. JOM, 1987, 39(11): 34
[37] Kim C W, Kim Y C, Kim J H, et al. Effect of alloying elements on the thermal conductivity and casting characteristics of aluminum alloys in high pressure die casting [J]. Korean J. Met. Mater., 2018, 56: 805
doi: 10.3365/KJMM.2018.56.11.805
[38] Zhao Z, Li D, Yan X, et al. Insights into the dual effects of Ti on the grain refinement and mechanical properties of hypoeutectic Al-Si alloys [J]. J. Mater. Sci. Technol., 2024, 189: 44
doi: 10.1016/j.jmst.2023.12.014
[39] Haga T, Imamura S, Fuse H. Fluidity investigation of pure Al and Al-Si alloys [J]. Materials, 2021, 14: 5372
doi: 10.3390/ma14185372
[40] Barenji R V. Casting fluidity, viscosity, microstructure and tensile properties of aluminum matrix composites with different Mg2Si contents [J]. Rare Met., 2022, 41: 2767
doi: 10.1007/s12598-017-0923-8
[41] Heidarzadeh A, Emamy M, Rahimzadeh A, et al. The effect of copper addition on the fluidity and viscosity of an Al-Mg-Si alloy [J]. J. Mater. Eng. Perform., 2014, 23: 469
doi: 10.1007/s11665-013-0794-6
[42] Taghaddos E, Hejazi M M, Taghiabadi R, et al. Effect of iron-intermetallics on the fluidity of 413 aluminum alloy [J]. J. Alloys Compd., 2009, 468: 539
doi: 10.1016/j.jallcom.2008.01.079
[43] Niu G, Mao J, Wang J. Effect of Ce addition on fluidity of casting aluminum alloy A356 [J]. Metall. Mater. Trans., 2019, 50A: 5935
[44] Prukkanon W, Srisukhumbowornchai N, Limmaneevichitr C. Influence of Sc modification on the fluidity of an A356 aluminum alloy [J]. J. Alloys Compd., 2009, 487: 453
doi: 10.1016/j.jallcom.2009.07.169
[45] Çolak M, Kayikci R, Dispinar D. Influence of different cross sections on fluidity characteristics of A356 [J]. Trans. Indian Inst. Met., 2015, 68: 275
doi: 10.1007/s12666-014-0455-y
[46] Akhtar S, Liu Y X, Wang P Z, et al. Understanding the formation mechanism of defect bands through ESCs evolution in non-heat-treated high-pressure die-cast AlSi9MnVZr alloy: Role of shot speeds and intensification pressure [J]. J. Mater. Process. Technol., 2025, 341: 118915
doi: 10.1016/j.jmatprotec.2025.118915
[47] Liu Y X, Liu Y C, Wang P Z, et al. A newly-developed high-pressure die-cast Al-1.5Fe-1Ni alloy with high thermal conductivity: Design, microstructure, and properties [J]. J. Mater. Sci. Technol., 2026, 245: 130
doi: 10.1016/j.jmst.2025.04.044
[48] Otarawanna S, Gourlay C M, Laukli H I, et al. Formation of the surface layer in hypoeutectic Al-alloy high-pressure die castings [J]. Mater. Chem. Phys., 2011, 130: 251
doi: 10.1016/j.matchemphys.2011.06.035
[49] Liu Y X, Xiong S M. Research progress on thermal conductivity of high-pressure die-cast aluminum alloys [J]. Metals, 2024, 14: 370
doi: 10.3390/met14040370
[50] Liu W N, Zhang W, Wang P Y, et al. Effect of slow shot speed on externally solidified crystal, porosity and tensile property in a newly developed high-pressure die-cast Al-Si alloy [J]. China Foundry, 2024, 21: 11
doi: 10.1007/s41230-023-3037-y
[51] Jiao X Y, Wang P Y, Liu Y X, et al. The characterization of porosity and externally solidified crystals in a high pressure die casting hypoeutectic Al-Si alloy using a newly developed ceramic shot sleeve [J]. Mater. Lett., 2024, 360: 136045
doi: 10.1016/j.matlet.2024.136045
[52] Bi C, Xiong S M, Li X B, et al. Development of a fluid-particle model in simulating the motion of external solidified crystals and the evolution of defect bands in high-pressure die casting [J]. Metall. Mater. Trans., 2016, 47B: 939
[53] Hou Y Y, Wu M W, Huang F, et al. Defect band formation in high pressure die casting AE44 magnesium alloy [J]. China Foundry, 2022, 19: 201
doi: 10.1007/s41230-022-1220-1
[54] Gourlay C M, Dahle A K, Laukli H I. Segregation band formation in Al-Si die castings [J]. Metall. Mater. Trans., 2004, 35A: 2881
[55] Gourlay C M, Laukli H I, Dahle A K. Defect band characteristics in Mg-Al and Al-Si high-pressure die castings [J]. Metall. Mater. Trans., 2007, 38A: 1833
[56] Lee S G, Patel G R, Gokhale A M. Characterization of the effects of process parameters on macrosegregation in a high-pressure die-cast magnesium alloy [J]. Mater. Charact., 2005, 55: 219
doi: 10.1016/j.matchar.2005.05.009
[57] Jalili Nikroo A, Akhlaghi M, Ahmadi Najafabadi M. Simulation and analysis of flow in the injection chamber of die casting machine during the slow shot phase [J]. Int. J. Adv. Manuf. Technol., 2009, 41: 31
doi: 10.1007/s00170-008-1444-2
[58] Niu G D, Wang J, Li J P, et al. The formation mechanism of the chill fine-grain layer with high supersaturation and its influence on the mechanical properties of die casting Al-7Si-0.5Mg alloy [J]. Mater. Sci. Eng., 2022, A833: 142544
[59] Ananth R, Gill W N. Dendritic growth of an elliptical paraboloid with forced convection in the melt [J]. J. Fluid Mech., 1989, 208: 575
doi: 10.1017/S0022112089002946
[60] Zhang A, Meng S X, Guo Z P, et al. Dendritic growth under natural and forced convection in Al-Cu alloys: From equiaxed to columnar dendrites and from 2D to 3D phase-field simulations [J]. Metall. Mater. Trans., 2019, 50B: 1514
[61] Hou Y Y, Wu M W, Tian B H, et al. Characteristics and formation mechanisms of defect bands in vacuum-assisted high-pressure die casting AE44 alloy [J]. Trans. Nonferrous Met. Soc. China, 2022, 32: 1852
doi: 10.1016/S1003-6326(22)65913-2
[62] Akhtar S, Liu Y X, Wang P Z, et al. The effect of section thickness and intensification pressure on the microstructures of non-heat-treated AlSi9MnVZr alloy [J]. J. Alloys Compd., 2025, 1010: 178105
doi: 10.1016/j.jallcom.2024.178105
[63] Kang H J, Yoon P H, Lee G H, et al. Evaluation of the gas porosity and mechanical properties of vacuum assisted pore-free die-cast Al-Si-Cu alloy [J]. Vacuum, 2021, 184: 109917
doi: 10.1016/j.vacuum.2020.109917
[64] Kang H J, Jang H S, Oh S H, et al. Effects of gate system design on pore defects and mechanical properties of pore-free die-cast Al-Si-Cu alloy [J]. Mater. Today Commun., 2022, 31: 103673
[65] Jiao X Y, Zhang Y F, Wang J, et al. Characterization of externally solidified crystals in a high-pressure die-cast AlSi10MnMg alloy and their effect on porosities and mechanical properties [J]. J. Mater. Process. Technol., 2021, 298: 117299
doi: 10.1016/j.jmatprotec.2021.117299
[66] Laukli H I, Gourlay C M, Dahle A K, et al. Effects of Si content on defect band formation in hypoeutectic Al-Si die castings [J]. Mater. Sci. Eng., 2005, A413-414: 92
[67] Bhagavath S, Gong Z X, Wigger T, et al. Mechanisms of gas and shrinkage porosity formation in solidifying shear bands [J]. J. Mater. Process. Technol., 2022, 299: 117338
doi: 10.1016/j.jmatprotec.2021.117338
[68] Hegde S, Prabhu K N. Modification of eutectic silicon in Al-Si alloys [J]. J. Mater. Sci., 2008, 43: 3009
doi: 10.1007/s10853-008-2505-5
[69] Zhang A, Guo Z P, Jiang B, et al. Multiphase and multiphysics modeling of dendrite growth and gas porosity evolution during solidification [J]. Acta Mater., 2021, 214: 117005
doi: 10.1016/j.actamat.2021.117005
[70] Otarawanna S, Gourlay C M, Laukli H I, et al. The thickness of defect bands in high-pressure die castings [J]. Mater. Charact., 2009, 60: 1432
doi: 10.1016/j.matchar.2009.06.016
[71] Cao Y Y, Guo Z P, Xiong S M. Determination of interfacial heat transfer coefficient and its application in high pressure die casting process [J]. China Foundry, 2014, 11: 314
[72] Jiao X Y, Wang J, Liu C, et al. Influence of slow-shot speed on PSPs and porosity of AlSi17Cu2.5 alloy during high pressure die casting [J]. J. Mater. Process. Technol., 2019, 268: 63
doi: 10.1016/j.jmatprotec.2019.01.008
[73] Yang J, Liu B, Shu D, et al. Influence of high injection speed on porosity and mechanical properties of high-pressure die-casting Al-Si-Mg-Mn alloy [J]. Metall. Mater. Trans., 2025, 56B: 5296
[74] Lindsey D, Wallace J F. Heat and fluid flow in the die casting process [R]. Congress of the Society of Die Casting Engineers: SDCE Paper No. 12. 1968
[75] Djurdjevic M B, Manasijevic S, Patarić A, et al. Challenges by latent heat calculation—Competition among analytical and computational methods [J]. Int. Commun. Heat Mass Transf., 2024, 157: 107704
doi: 10.1016/j.icheatmasstransfer.2024.107704
[76] Jiao X Y, Liu Y X, Wang J, et al. The microstructure characteristics and fracture behavior of the polyhedral primary iron-rich phase and plate-shaped eutectic iron-rich phase in a high-pressure die-cast AlSi10MnMg alloy [J]. J. Mater. Sci. Technol., 2023, 140: 201
doi: 10.1016/j.jmst.2022.09.014
[77] Noble A T, Monroe C A, Monroe A K. Predicting flow lengths in die casting in 3D [A]. Die Casting Congress & Exposition: Vol. 18 [C]. Louisville, Kentucky: North American Die Casting Association (NADCA), 2013: 1
[78] Gašpár Š, Coranič T, Majerník J, et al. Influence of gating system parameters of die-cast molds on properties of Al-Si castings [J]. Materials, 2021, 14: 3755
doi: 10.3390/ma14133755
[79] Cleary P W, Ha J, Prakash M, et al. Short shots and industrial case studies: Understanding fluid flow and solidification in high pressure die casting [J]. Appl. Math. Model., 2010, 34: 2018
doi: 10.1016/j.apm.2009.10.015
[80] Zhu B W, Li L X, Liu X, et al. Effect of viscosity measurement method to simulate high pressure die casting of thin-wall AlSi10MnMg alloy castings [J]. J. Mater. Eng. Perform., 2015, 24: 5032
doi: 10.1007/s11665-015-1783-8
[81] Herman E. The gating equation [J]. Die Cast. Eng. (USA), 2002, 46(6): 44
[82] Zhang A, Guo Z P, Wang Q G, et al. Three-dimensional numerical simulation of bubble rising in viscous liquids: A conservative phase-field lattice-Boltzmann study [J]. Phys. Fluids, 2019, 31: 063106
[83] Miller R A. The “gating equation” updated [A]. Die Casting Congress and Exposition [C]. Indianapolis, Indiana: North American Die Casting Association (NADCA), 2015: 1
[84] Timelli G, Fabrizi A. The effects of microstructure heterogeneities and casting defects on the mechanical properties of high-pressure die-cast AlSi9Cu3(Fe) alloys [J]. Metall. Mater. Trans., 2014, 45A: 5486
[85] Durmuş M, Dispinar D, Gavgali M, et al. Evaluation of Fe content on the fluidity of A356 aluminum alloy by new fluidity index [J]. Int. J. Met., 2025, 19: 1950
[86] Marathe S, Quadros C. Thermal hot spot prediction in high pressure die casting by determination of chvorinovs rule shape constant [J]. Mater. Today: Proc., 2021, 47: 5607
[87] Monroe C A, Monroe A K. Predicting flow lengths in die casting including heat advection [A]. Die Casting Congress & Exposition: Vol. 10 [C]. Indianapolis, Indiana: North American Die Casting Association (NADCA), 2012: 1
[88] Han Q, Xu H. Fluidity of alloys under high pressure die casting conditions [J]. Scr. Mater., 2005, 53: 7
doi: 10.1016/j.scriptamat.2005.03.025
[89] Bhat M S, Poirier D R, Heinrich J C. Permeability for cross flow through columnar-dendritic alloys [J]. Metall. Mater. Trans., 1995, 26B: 1049
[90] Miller R A. Fluidity from a heat transfer perspective [A]. Die Casting Congress & Exposition [C]. Columbus, Ohio: North American Die Casting Association (NADCA), 2016: 1
[91] Flemings M C, Niyama E, Taylor H F. Fluidity of aluminum alloys: An experimental and quantitative evaluation [J]. Trans. Am. Foundrymens Soc., 1961, 69: 625
[92] Jafarizadeh A, Ahmadzadeh M, Mahmoudzadeh S, et al. A new approach for predicting the pressure drop in various types of metal foams using a combination of CFD and machine learning regression models [J]. Transp. Porous Media, 2023, 147: 59
doi: 10.1007/s11242-022-01895-0
[1] 阴嘉琳, 石磊, 武传松. 超声振动对镁/铝异质合金搅拌摩擦搭接焊接头界面组织演变的影响[J]. 金属学报, 2026, 62(1): 133-147.
[2] 韩鸿华, 史清宇, 杨诚乐, 孔德帅, 陈高强. 铝合金搅拌摩擦焊热-力-流耦合仿真及材料迁移轨迹解析[J]. 金属学报, 2026, 62(1): 148-158.
[3] 肖文龙, 臧晨阳, 郭锦涛, 冯佳文, 马朝利. 基于原位电阻法的7A65铝合金厚板双级时效工艺[J]. 金属学报, 2025, 61(8): 1153-1164.
[4] 孙军, 刘刚, 杨冲, 张鹏, 薛航. 耐热铝合金:组织设计与合金制备[J]. 金属学报, 2025, 61(4): 521-525.
[5] 罗列文, 王明洋, 高志明, 夏大海, 邓意达, 胡文彬. 高强铝合金晶界氢陷阱的原子尺度作用机制[J]. 金属学报, 2025, 61(11): 1747-1757.
[6] 郑潇禹, 陈辛, 何美玲, 黄奇, 李亚, 孔毅, 杜勇. 基于晶体塑性的6XXX铝合金力学性能多尺度计算[J]. 金属学报, 2025, 61(11): 1758-1768.
[7] 万杰, 李皓天, 刘书基, 路洪洲, 王立生, 张振栋, 刘春海, 贾建磊, 刘海峰, 陈豫增. Al-Nb-B细化剂形核质点的弥散化及其对铸造铝合金组织及力学性能的影响[J]. 金属学报, 2025, 61(1): 117-128.
[8] 韩英, 吴雨航, 赵春禄, 张靖实, 李振民, 冉旭. 选区激光熔化成形Al-Si-Fe-Mn-Ni合金的高温蠕变行为[J]. 金属学报, 2025, 61(1): 154-164.
[9] 徐洋, 柯黎明, 聂浩, 夏春, 刘强, 陈书锦. 局部强冷作用下厚板铝合金/镁合金搅拌摩擦焊界面金属间化合物的析出行为[J]. 金属学报, 2024, 60(6): 777-788.
[10] 王勇, 张卫文, 杨超, 王智. 钛合金三维点阵结构增韧纳米铝合金的力学性能和变形行为[J]. 金属学报, 2024, 60(2): 247-260.
[11] 介子奇, 刘鼎元, $\boxed{\hbox{张军}}$. B、Zr复合添加对IN718高温合金流动性的影响[J]. 金属学报, 2024, 60(12): 1615-1621.
[12] 耿汝伟, 王林, 魏正英, 麻宁绪. 铝合金熔滴复合电弧增材组织演化及外延生长特性[J]. 金属学报, 2024, 60(11): 1584-1594.
[13] 王宗谱, 王卫国, Rohrer Gregory S, 陈松, 洪丽华, 林燕, 冯小铮, 任帅, 周邦新. 不同温度轧制Al-Zn-Mg-Cu合金再结晶后的{111}/{111}近奇异晶界[J]. 金属学报, 2023, 59(7): 947-960.
[14] 夏大海, 计元元, 毛英畅, 邓成满, 祝钰, 胡文彬. 2024铝合金在模拟动态海水/大气界面环境中的局部腐蚀机制[J]. 金属学报, 2023, 59(2): 297-308.
[15] 高建宝, 李志诚, 刘佳, 张金良, 宋波, 张利军. 计算辅助高性能增材制造铝合金开发的研究现状与展望[J]. 金属学报, 2023, 59(1): 87-105.