Please wait a minute...
金属学报  2010, Vol. 46 Issue (1): 111-117    
  论文 本期目录 | 过刊浏览 |
喷丸强化过程及冲击效应的数值模拟
张洪伟; 张以都;  吴琼
北京航空航天大学机械工程及自动化学院; 虚拟现实技术与系统国家重点实验室; 北京 100191
NUMERICAL SIMULATIONS OF SHOT-PEENING PROCESS AND IMPACT EFFECT
ZHANG Hongwei; ZHANG Yidu; WU Qiong
School of Mechanical Engineering and Automation; Beihang University; State Key Laboratory of Virtual Reality Technology and Systems; Beijing 100191
引用本文:

张洪伟 张以都 吴琼. 喷丸强化过程及冲击效应的数值模拟[J]. 金属学报, 2010, 46(1): 111-117.
, , . NUMERICAL SIMULATIONS OF SHOT-PEENING PROCESS AND IMPACT EFFECT[J]. Acta Metall Sin, 2010, 46(1): 111-117.

全文: PDF(1352 KB)  
摘要: 

运用大型有限元软件LS-DYNA建立了喷丸强化处理过程的三维有限元模型, 研究了弹丸冲击作用下, 铝合金材料Al 2024-T3动态响应过程中的应力波结构、应变率效应及应力波衰减效应等动态参量; 研究了弹丸搭接率对于残余应力场的影响, 建立了高覆盖率多丸粒强化模型; 研究了冲击顺序、材料应变率及初始残余应力对强化效应的影响; 研究了喷丸强化后的表面微观变形特征. 分析结果表明, 弹丸高速冲击引起的弹塑性双波会在材料内部形成高应变率效应; 弹丸搭接率ζ对于强化效应有明显影响, ζ=1/2是近似的临界值; 不同冲击顺序对于强化效果的影响较小, 材料应变率对于强化效果有显著影响; 初始残余应力对于喷丸强化最终形成的残余应力场的影响取决于弹丸冲击速度; 经过喷丸强化处理, 零件表面形成微米级凹坑, 并且随着冲击次数和喷丸覆盖率的提高, 凹坑深度逐渐增加.

关键词 喷丸有限元法残余应力冲击应变率覆盖率    
Abstract

The shot--peening process and impact effect were simulated by using software LS--DYNA. Propagation and interaction of stress waves in the treated material were analyzed based on numerical simulation results. The stress wave structure, high strain-rate effect and attenuation of stress wave were also investigated. The overlapping ratio between shots was studied and the high peening coverage model was established. The effects of impact sequence, material strain--rate and initial residual stress on the residual stress and the surface deformation were examined. The results indicate that the high strain-rate induced by shot impact is related to the elastic and plastic wave structure. The surface quality is essentially affected by overlapping ratio and its approximate critical value is found to be 1/2. The effect of impact sequence can be neglected, but the strain rate plays an important role in determining the level and distribution of the residual stress field. The influence of original residual stress in the target is significantly dependent on the impact velocity. The shallow pocket in depth is induced on the top surface of material by multiple impacts, and the surface deformation increases with the increase of impact time.

Key wordsshot-peening    finite element method    residual stress    impact    strain rate    coverage ratio
收稿日期: 2009-05-12     
ZTFLH: 

TG142.7

 
基金资助:

虚拟现实技术与系统国家重点实验室资助项目

作者简介: 张洪伟, 男, 1978年生, 博士

[1] Luan W L, Tu S D. Chin Mech Eng, 2005; 16: 1405.
(栾伟玲, 涂善东. 中国机械工程, 2005; 16: 1405)
[2] Al–Hassani S T S. In: Niku–lari A ed., Proc 1st Int Conf on Shot Peening, Paris: Pergamon Press, 1981: 583
[3] Al–Obaid Y F. Mech Mater, 1995; 19: 251
[4] Kobayashi M, Matsui T, Murakami Y. Int J Fatigue, 1998; 20: 351
[5] Johnson W. Impact Strength of Materials. London: Arnold, 1972: 3
[6] Meguid S A, Klair M S. J Mech Work Technol, 1985; 11: 87
[7] Meguid S A, Klair M S. Int J Mech Sci, 1985; 27: 157
[8] Al–Obaid Y F T. Comput Struct, 1990; 36: 681
[9] Schiffner K, Helling C D G. Comput Struct, 1999; 72: 329
[10] Meguid S A, Shagal G, Stranart J C, Daly J. Finite Elem Anal Des, 1999; 31: 179
[11] Hong T, Ooi J Y, Shaw B A. Adv Eng Software, 2008; 39: 743
[12] Baragetti S. Int J Comput Appl Technol, 2001; 14: 51
[13] Meguid S A, Shagal G, Stranart J C. Int J Impact Eng, 2002; 27: 119
[14] Majzoobi G H, Azizi R, Alavi Nia A. A. J Mater Process Technol, 2005; 164–165: 1226
[15] Ling X, PengWW, Ni H F. J Mech Eng, 2006; 42: 182
(凌祥, 彭薇薇, 倪红芳. 机械工程学报, 2006; 42: 182)
[16] Wang L L. Foundation of Stress Waves. Beijing: National Defense Industry Press, 2005: 1
(王礼立. 应力波基础. 北京:国防工业出版社, 2005: 1)

[17] Hallquist J O. LS–dyna Keyword User’s Manual Version 970. California: Livermore Software Technology Corporation, 2003: 818
[18] Mandal S, Rice J, Elmustafa A A. J Mater Process Technol, 2008; 203: 401

[1] 杜金辉, 毕中南, 曲敬龙. 三联冶炼GH4169合金研究进展[J]. 金属学报, 2023, 59(9): 1159-1172.
[2] 毕中南, 秦海龙, 刘沛, 史松宜, 谢锦丽, 张继. 高温合金锻件残余应力量化表征及控制技术研究进展[J]. 金属学报, 2023, 59(9): 1144-1158.
[3] 李时磊, 李阳, 王友康, 王胜杰, 何伦华, 孙光爱, 肖体乔, 王沿东. 基于中子与同步辐射技术的工程材料/部件多尺度残余应力评价[J]. 金属学报, 2023, 59(8): 1001-1014.
[4] 黄鼎, 乔岩欣, 杨兰兰, 王金龙, 陈明辉, 朱圣龙, 王福会. 基体表面喷丸处理对纳米晶涂层循环氧化行为的影响[J]. 金属学报, 2023, 59(5): 668-678.
[5] 王重阳, 韩世伟, 谢峰, 胡龙, 邓德安. 固态相变和软化效应对超高强钢焊接残余应力的影响[J]. 金属学报, 2023, 59(12): 1613-1623.
[6] 张开元, 董文超, 赵栋, 李世键, 陆善平. 固态相变对Fe-Co-Ni超高强度钢长臂梁构件焊接-淬火过程应力和变形的影响[J]. 金属学报, 2023, 59(12): 1633-1643.
[7] 卢海飞, 吕继铭, 罗开玉, 鲁金忠. 激光热力交互增材制造Ti6Al4V合金的组织及力学性能[J]. 金属学报, 2023, 59(1): 125-135.
[8] 吴进, 杨杰, 陈浩峰. 纳入残余应力时不同拘束下DMWJ的断裂行为[J]. 金属学报, 2022, 58(7): 956-964.
[9] 张新房, 向思奇, 易坤, 郭敬东. 脉冲电流调控金属固体中的残余应力[J]. 金属学报, 2022, 58(5): 581-598.
[10] 陈扬, 毛萍莉, 刘正, 王志, 曹耕晟. 高速冲击载荷下预压缩AZ31镁合金的退孪生行为与动态力学性能[J]. 金属学报, 2022, 58(5): 660-672.
[11] 苏凯新, 张继旺, 张艳斌, 闫涛, 李行, 纪东东. 微弧氧化6082-T6铝合金的高周疲劳性能及残余应力松弛机理[J]. 金属学报, 2022, 58(3): 334-344.
[12] 朱东明, 何江里, 史根豪, 王青峰. 热输入对Q500qE钢模拟CGHAZ微观组织和冲击韧性的影响[J]. 金属学报, 2022, 58(12): 1581-1588.
[13] 骆文泽, 胡龙, 邓德安. SUS316不锈钢马鞍形管-管接头的残余应力数值模拟及高效计算方法开发[J]. 金属学报, 2022, 58(10): 1334-1348.
[14] 李少杰, 金剑锋, 宋宇豪, 王明涛, 唐帅, 宗亚平, 秦高梧. “工艺-组织-性能”模拟研究Mg-Gd-Y合金混晶组织[J]. 金属学报, 2022, 58(1): 114-128.
[15] 蒋中华, 杜军毅, 王培, 郑建能, 李殿中, 李依依. M-A岛高温回火转变产物对核电SA508-3钢冲击韧性影响机制[J]. 金属学报, 2021, 57(7): 891-902.