Please wait a minute...
金属学报  2019, Vol. 55 Issue (9): 1221-1230    DOI: 10.11900/0412.1961.2019.00097
  研究论文 本期目录 | 过刊浏览 |
DD407/IN718高温合金异质焊接接头的组织及高温变形行为
刘杨,王磊(),宋秀,梁涛沙
东北大学材料各向异性与织构教育部重点实验室 沈阳 110819
Microstructure and High-Temperature Deformation Behavior of Dissimilar Superalloy Welded Joint of DD407/IN718
LIU Yang,WANG Lei(),SONG Xiu,LIANG Taosha
Key Laboratory for Anisotropy and Texture of Materials, Ministry of Education, Northeastern University, Shenyang 110819, China
引用本文:

刘杨,王磊,宋秀,梁涛沙. DD407/IN718高温合金异质焊接接头的组织及高温变形行为[J]. 金属学报, 2019, 55(9): 1221-1230.
Yang LIU, Lei WANG, Xiu SONG, Taosha LIANG. Microstructure and High-Temperature Deformation Behavior of Dissimilar Superalloy Welded Joint of DD407/IN718[J]. Acta Metall Sin, 2019, 55(9): 1221-1230.

全文: PDF(30541 KB)   HTML
摘要: 

采用连续光纤激光器对DD407单晶、IN718多晶高温合金实施对接焊,研究了标准热处理前后接头微观组织、成分偏析的演化及接头的高温拉伸变形行为。结果表明,在优化焊接参数下,接头熔合区组织包括平面晶区、胞状晶区、柱状晶区和等轴晶区,熔合区中心线两侧枝晶生长形态差异明显。焊接态接头熔合区硬度低,存在明显的微观偏析;标准热处理后,熔合区偏析得以改善,接头熔合区硬度超过两侧母材硬度。接头单晶热影响区存在局部硬化区,多晶热影响区存在较窄的软化区及晶界液化现象。接头在650 ℃拉伸时,抗拉强度达1111 MPa,延伸率可达9.42%,断裂位置位于多晶母材侧。接头高温拉伸塑性变形方式主要为单晶母材、熔合区的位错多系滑移以及多晶母材的位错滑移和晶界滑动,拉伸断口呈多源开裂特征,裂纹源区存在韧窝和冰糖状断口形貌。接头多晶侧热影响区的晶界液化并未对接头短时高温力学性能产生明显影响。

关键词 光纤激光焊接单晶/多晶异质金属焊接接头微观偏析高温变形断裂行为    
Abstract

Welding is an important joining method to fabricate the dissimilar welding integral blisk structure of single crystal and polycrystalline superalloy. The microstructure and properties of the welded joint are the key factors to determine the reliability of the integral blisk structure of dissimilar superalloys. The single crystal superalloy of DD407 and polycrystalline superalloy of IN718 were butt welded by continuous fiber laser system. The evolution of microstructure and composition segregation of the welded joints fabricated under the optimized welding parameters as-welded (AW) and after post weld heat treatment (PWHT) were investigated. The high temperature tensile deformation behavior of the welded joint after PWHT was also examined. The results show that the microstructures of fusion zone (FZ) in the welded joint consist of planar crystal, cellular crystal, columnar crystal and equiax crystal. The difference of the dendrite microstructures between the two sides of the weld centerline is very obvious. In terms of the joint as-welded, the microhardness of the FZ is low and there exists obvious micro-segregation. After PWHT, the micro-segregation has been improved and the microhardness increases significantly in the FZ which is much more than those of both base metals (BMs) of DD407 and IN718 alloys. There exists local hardening zone in the heat-affected zone (HAZ) of DD407 single crystal alloy and narrow softening zone and grain boundary liquation phenomenon in the HAZ of IN718 polycrystalline alloy. The ultimate tensile strength and elongation of the welded joint after tensile test at 650 ℃ are 1111 MPa and 9.42%, respectively. And the tensile specimen of the welded joint fails in the BM of IN718 polycrystalline alloy. The main deformation mode of the laser welded joint at high temperature includes the multi-slips of dislocation in the BM and FZ of single crystal alloy, and the dislocation slip and grain-boundary sliding in the BM of polycrystalline alloy. The tensile fracture surface is characterized by multi-source cracking, and the dimple and crystal sugar shaped facture surface exist simultaneously in the crack source area, which is a mixed fracture of microvoid aggregation and intergranular fracture. So the tensile fracture mechanism contains micro-void accumulation fracture and inter-granular fracture. The grain boundary liquefaction in the HAZ of IN718 polycrystalline does not affect the short-time high temperature mechanical properties of the welded joints.

Key wordsfiber laser welding    dissimilar welded joint of single crystal and polycrystalline alloy    dissimilar welded joint of single crystal and polycrystalline alloymicro-segregation    high-temperature deformation    fracture behavior
收稿日期: 2019-04-03     
ZTFLH:  TG132.32  
基金资助:国家自然科学基金项目(Nos.51571052、 U1708253,51874090);中央高校基本科研业务费专项资金项目(No.180213006)
作者简介: 刘 杨,男,1978年生,副教授,博士
MaterialCCrCoWMoAlTiNbTaFeNi
DD4070.0078.0505.5005.0002.2505.9502.000-3.500-Bal.
IN7180.04019.000--3.0500.5000.9005.250-Bal.52.500
表1  DD407单晶合金、IN718多晶合金的化学成分
图1  DD407/IN718合金激光焊接接头拉伸变形取样尺寸示意图
图2  不同焊接参数下DD407/IN718合金激光焊接接头上、下表面及截面宏观形貌
图3  DD407/IN718合金激光焊接接头(聚焦镜焦距250 mm,离焦量-8 mm,焊接功率1600 W,焊接速率2.1 mm/min)的焊接态显微组织
图4  标准热处理后DD407/IN718合金激光焊接接头的SEM像
图5  热处理前后接头的显微硬度分布
图6  DD407/IN718接头的合金元素分布
图7  DD407/IN718接头和2种母材的应力-应变曲线及拉伸性能
图8  DD407/IN718接头和母材拉伸后的截面形貌及断口SEM像
图9  DD407/IN718接头高温拉伸断口截面SEM像
图10  DD407/IN718接头高温拉伸断口处的SEM像
[1] HuangQ Y, LiH K. Superalloy [M]. Beijing: Metallurgical Industry Press, 2000: 22
[1] 黄乾尧, 李汉康. 高温合金 [M]. 北京: 冶金工业出版社, 2000: 22)
[2] ChenL, XiaX T, QiuM. Analysis and control of fretting wear for blade bearing in wind turbine [J]. Appl. Mech. Mater., 2010, 26-28: 167
[3] LiuQ Q. Fracture analysis for rotor blade tenon of an aeroengine compressor [J]. J. Mater. Eng., 1997, (6): 9
[3] 刘庆瑔. 某发动机压气机四级转子叶片榫头断裂分析 [J]. 材料工程, 1997, (6): 9)
[4] MishraR K, ThomasJ, SrinivasanK, , et al. Failure analysis of an un-cooled turbine blade in an aero gas turbine engine [J]. Eng. Fail. Anal., 2017, 79: 836
[5] FuY Z, GaoH, WangX P, , et al. Machining the integral impeller and blisk of aero-Engines: A review of surface finishing and strengthening technologies [J]. Chin. J. Mech. Eng., 2017, 30: 528
[6] HuangC F. Modern aeroengine integral blisk and its manufacturing technology [J]. Aeronaut. Manuf. Technol., 2006, (4): 94
[6] 黄春峰. 现代航空发动机整体叶盘及其制造技术 [J]. 航空制造技术, 2006, (4): 94)
[7] AschenbruckJ, AdamczukR, SeumeJ R. Recent progress in turbine blade and compressor blisk regeneration [J]. Proc. CIRP, 2014, 22: 256
[8] MateoA. On the feasibility of BLISK produced by linear friction welding [J]. Rev. Metal., 2014, 50(3): e023
[9] ChenG Q, ZhangB G, LüT M, , et al. Causes and control of welding cracks in electron-beam-welded superalloy GH4169 joints [J]. Trans. Nonferrous Met. Soc. China, 2013, 23: 1971
[10] ZhangD Y, NiuW, CaoX Y, , et al. Effect of standard heat treatment on the microstructure and mechanical properties of selective laser melting manufactured Inconel 718 superalloy [J]. Mater. Sci. Eng., 2015, A644: 32
[11] DuS G, WangX F, GaoM. Characteristics of the friction welding interface between single crystal superalloy DD3 and fine grained superalloy GH4169 [J]. Acta Metall. Sin., 2015, 51: 951
[11] 杜随更, 王喜锋, 高 漫. 单晶DD3与细晶GH4169高温合金摩擦焊接界面表征 [J]. 金属学报, 2015, 51: 951
[12] PouranvariM, EkramiA, KokabiA H. Solidification and solid state phenomena during TLP bonding of IN718 superalloy using Ni-Si-B ternary filler alloy [J]. J. Alloys Compd., 2013, 563: 143
[13] YanF, WangC M, WangY J, , et al. A study of the mechanism of laser welding defects in low thermal expansion superalloy GH909 [J]. Mater. Charact., 2013, 78: 21
[14] HuangW P, YuH C, YinJ, , et al. Microstructure and mechanical properties of K4202 cast nickel base superalloy fabricated by selective laser melting [J]. Acta Metall. Sin., 2016, 52: 1089
[14] 黄文普, 喻寒琛, 殷 杰等. 激光选区熔化成形K4202镍基铸造高温合金的组织和性能 [J]. 金属学报, 2016, 52: 1089
[15] LiuS, MiG Y, YanF, , et al. Correlation of high power laser welding parameters with real weld geometry and microstructure [J]. Opt. Laser Technol., 2017, 94: 59
[16] DongD Y, LiuY, WangL, , et al. Effect of strain rate on dynamic deformation behavior of laser welded DP780 steel joints [J]. Acta Metall. Sin., 2013, 49: 1493
[16] 董丹阳, 刘 杨, 王 磊等. 应变速率对DP780钢激光焊接接头动态变形行为的影响 [J]. 金属学报, 2013, 49: 1493
[17] LiY J, WangJ, LiuP. Welding of Badly Welding Dissimilar and Application [M]. Beijing: Chemical Industry Press, 2004: 1
[17] 李亚江, 王 娟, 刘 鹏. 异种难焊材料的焊接及应用 [M]. 北京: 化学工业出版社, 2004: 1)
[18] YuG, ZhaoS S, ZhangY J, , et al. Research on key issues of laser welding of dissimilar metal [J]. Chin. J. Lasers, 2009, 36: 261
[18] 虞 钢, 赵树森, 张永杰等. 异种金属激光焊接关键问题研究 [J]. 中国激光, 2009, 36: 261
[19] WeiC H, ZhangJ, YangS L, , et al. Microstructures and mechanical properties for laser tailor welded blanks of DP590 and low carbon steels [J]. J. Magn. Magn. Mater., 2013,42(suppl.2): 68
[20] OzakiH, KutsunaM. Laser-roll welding of a dissimilar metal joint of low carbon steel to aluminium alloy using 2 kW fibre laser [J]. Weld. Int., 2009, 23: 345
[21] LiuJ, ZhaoZ Y. Residual stress distribution of electron beam welded dissimilar superalloy sheet joints after heat treatment [J]. Trans. Mater. Heat Treat., 2016, 37(2): 245
[21] 刘 谨, 赵志毅. 异种高温合金板材电子束焊接及热处理后残余应力特征 [J]. 材料热处理学报, 2016, 37(2): 245)
[22] ChamanfarA, MonajatiH, RosenbaumA, , et al. Microstructure and mechanical properties of surface and subsurface layers in broached and shot-peened Inconel-718 gas turbine disc fir-trees [J]. Mater. Charact., 2017, 132: 53
[23] GuoJ T. Materials Science and Engineering for Superalloys (Book 1) [M]. Beijing: Science Press, 2008: 1
[23] 郭建亭. 高温合金材料学-上册 [M]. 北京: 科学出版社, 2008: 1)
[24] KhajaS, MehtaK K, BabuR V, , et al. Mechanical properties anisotropy of isothermally forged and precipitation hardened inconel 718 disk [J]. Metall. Mater. Trans., 2015, 46A: 1140
[25] WuD J, YinB, ZhangW Z, , et al. Nd: YAG laser beam welding invar36 alloy [J]. Chin. J. Lasers, 2008, 35: 1773
[25] 吴东江, 尹 波, 张维哲等. Nd: YAG激光焊接殷钢材料的工艺研究 [J]. 中国激光, 2008, 35: 1773
[26] KouS. Welding Metallurgy [M]. 2nd Ed., Hoboken: Wiley-Interscience, 2003: 56
[27] PangM, YuG, WangH H, , et al. Microstructure study of laser welding cast nickel-based superalloy K418 [J]. J. Mater. Process. Technol., 2008, 207: 271
[28] RamG D J, ReddyA V, RaoK P, , et al. Microstructure and tensile properties of inconel 718 pulsed Nd-YAG laser welds [J]. J. Mater. Process. Technol., 2005, 167: 73
[29] ThompsonE G. Hot-cracking studies of inconel 718 weld heat-affected zones [J]. Weld. J., 1969, 48: 70
[30] ThompsonR G, GenculuS. Microstructural evolution in the HAZ of inconel 718 and correlation with the hot ductility test [J]. Weld. J., 1983, 62: 337S
[31] ThompsonR G, CassimusJ J, MayoD E, , et al. The relationship between grain size and microfissuring in alloy 718 [J]. Weld. J., 1985, 64: 91
[32] LiuY C, GuoQ Y, LiC, , et al. Recent progress on evolution of precipi-tates in inconel 718 superalloy [J]. Acta Metall. Sin., 2016, 52: 1259
[32] 刘永长, 郭倩颖, 李 冲等. Inconel718高温合金中析出相演变研究进展 [J]. 金属学报, 2016, 52: 1259
[33] PengZ F, RenY Y, LuoY S, , et al. Characteristics of microstructure and element distribution of nickel-base single crystal superalloy CMSX-2 after high temperature creep [J]. Acta Metall. Sin., 2002, 38: 135
[33] 彭志方, 任遥遥, 骆宇时等. 镍基单晶合金CMSX-2高温蠕变后的显微组织及合金元素分布特征 [J]. 金属学报, 2002, 38: 135
[34] ShengL Y, YangF, GuoJ T, , et al. Anomalous yield and intermediate temperature brittleness behaviors of directionally solidified nickel-based superalloy [J]. Trans. Nonferrous Met. Soc. China, 2014, 24: 673
[35] HuG X, CaiX, RongY H. Fundamentals of Materials Science [M]. 3rd Ed., Shanghai: Shanghai Jiao Tong University Press, 2000: 172
[35] 胡庚祥, 蔡 珣, 戎咏华. 材料科学基础 [M]. 第3版, 上海: 上海交通大学出版社, 2000: 172)
[1] 吴进, 杨杰, 陈浩峰. 纳入残余应力时不同拘束下DMWJ的断裂行为[J]. 金属学报, 2022, 58(7): 956-964.
[2] 范国华, 缪克松, 李丹阳, 夏夷平, 吴昊. 从局域应力/应变视角理解异构金属材料的强韧化行为[J]. 金属学报, 2022, 58(11): 1427-1440.
[3] 杨杰, 王雷. 核电站DMWJ中材料拘束的影响与优化[J]. 金属学报, 2020, 56(6): 840-848.
[4] 赵燕春, 孙浩, 李春玲, 蒋建龙, 毛瑞鹏, 寇生中, 李春燕. 高强韧Ti-Ni基块体金属玻璃复合材料高温变形行为[J]. 金属学报, 2018, 54(12): 1818-1824.
[5] 冯祥利,王磊,刘杨. Q460钢焊接接头组织及动态断裂行为的研究*[J]. 金属学报, 2016, 52(7): 787-796.
[6] 钟华,李传军,王江,任忠鸣,钟云波,玄伟东. 强磁场对定向凝固Al-4.5Cu合金微观偏析的影响*[J]. 金属学报, 2016, 52(5): 575-582.
[7] 闫二虎,孙立贤,徐芬,徐达鸣. 基于Thermo-Calc和微观偏析统一模型对Al-6.32Cu-25.13Mg合金凝固路径的预测*[J]. 金属学报, 2016, 52(5): 632-640.
[8] 许志武,马志鹏,闫久春,张誉喾,张旭昀. Ti/Al异种合金接头原位拉伸应变场及断裂行为的研究*[J]. 金属学报, 2016, 52(11): 1403-1412.
[9] 梁后权, 郭鸿镇, 宁永权, 姚泽坤, 赵张龙. 基于软化机制的TC18钛合金本构关系研究*[J]. 金属学报, 2014, 50(7): 871-878.
[10] 张金钰, 刘刚, 孙军. 纳米金属多层膜的变形与断裂行为及其尺寸效应*[J]. 金属学报, 2014, 50(2): 169-182.
[11] 窦坤, 卿家胜, 王雷, 张晓峰, 王宝, 刘青, 董洪标. 基于微观偏析模型的连铸方坯内裂纹敏感性研究[J]. 金属学报, 2014, 50(12): 1505-1512.
[12] 孔凡涛,崔宁,陈玉勇,熊宁宁. Ti-43Al-9V-Y合金的高温变形行为研究[J]. 金属学报, 2013, 49(11): 1363-1368.
[13] 朱传琳,张俊宝,程从前,赵杰. 变形温度对冷喷涂304不锈钢涂层材料高温变形行为的影响[J]. 金属学报, 2013, 49(10): 1275-1280.
[14] 刘东升 程丙贵 陈圆圆. 低C含Cu NV-F690特厚钢板的精细组织和强韧性[J]. 金属学报, 2012, 48(3): 334-342.
[15] 赵光伟 李新中 徐达鸣 傅恒志 杜勇 贺跃辉. 三元合金单相凝固路径的统一解析模型[J]. 金属学报, 2011, 47(9): 1135-1140.