|
|
|
| NUMERICAL SIMULATIONS OF SHOT-PEENING PROCESS AND IMPACT EFFECT |
| ZHANG Hongwei; ZHANG Yidu; WU Qiong |
| School of Mechanical Engineering and Automation; Beihang University; State Key Laboratory of Virtual Reality Technology and Systems; Beijing 100191 |
|
Cite this article:
ZHANG Hongwei ZHANG Yidu WU Qiong. NUMERICAL SIMULATIONS OF SHOT-PEENING PROCESS AND IMPACT EFFECT. Acta Metall Sin, 2010, 46(1): 111-117.
|
|
|
Abstract The shot--peening process and impact effect were simulated by using software LS--DYNA. Propagation and interaction of stress waves in the treated material were analyzed based on numerical simulation results. The stress wave structure, high strain-rate effect and attenuation of stress wave were also investigated. The overlapping ratio between shots was studied and the high peening coverage model was established. The effects of impact sequence, material strain--rate and initial residual stress on the residual stress and the surface deformation were examined. The results indicate that the high strain-rate induced by shot impact is related to the elastic and plastic wave structure. The surface quality is essentially affected by overlapping ratio and its approximate critical value is found to be 1/2. The effect of impact sequence can be neglected, but the strain rate plays an important role in determining the level and distribution of the residual stress field. The influence of original residual stress in the target is significantly dependent on the impact velocity. The shallow pocket in depth is induced on the top surface of material by multiple impacts, and the surface deformation increases with the increase of impact time.
|
|
Received: 12 May 2009
|
|
|
| Fund: Supported by State Key Laboratory of Virtual Reality Technology and Systems |
| [1] Luan W L, Tu S D. Chin Mech Eng, 2005; 16: 1405.
(栾伟玲, 涂善东. 中国机械工程, 2005; 16: 1405)
[2] Al–Hassani S T S. In: Niku–lari A ed., Proc 1st Int Conf on Shot Peening, Paris: Pergamon Press, 1981: 583
[3] Al–Obaid Y F. Mech Mater, 1995; 19: 251
[4] Kobayashi M, Matsui T, Murakami Y. Int J Fatigue, 1998; 20: 351
[5] Johnson W. Impact Strength of Materials. London: Arnold, 1972: 3
[6] Meguid S A, Klair M S. J Mech Work Technol, 1985; 11: 87
[7] Meguid S A, Klair M S. Int J Mech Sci, 1985; 27: 157
[8] Al–Obaid Y F T. Comput Struct, 1990; 36: 681
[9] Schiffner K, Helling C D G. Comput Struct, 1999; 72: 329
[10] Meguid S A, Shagal G, Stranart J C, Daly J. Finite Elem Anal Des, 1999; 31: 179
[11] Hong T, Ooi J Y, Shaw B A. Adv Eng Software, 2008; 39: 743
[12] Baragetti S. Int J Comput Appl Technol, 2001; 14: 51
[13] Meguid S A, Shagal G, Stranart J C. Int J Impact Eng, 2002; 27: 119
[14] Majzoobi G H, Azizi R, Alavi Nia A. A. J Mater Process Technol, 2005; 164–165: 1226
[15] Ling X, PengWW, Ni H F. J Mech Eng, 2006; 42: 182
(凌祥, 彭薇薇, 倪红芳. 机械工程学报, 2006; 42: 182)
[16] Wang L L. Foundation of Stress Waves. Beijing: National Defense Industry Press, 2005: 1
(王礼立. 应力波基础. 北京：国防工业出版社, 2005: 1)
[17] Hallquist J O. LS–dyna Keyword User’s Manual Version 970. California: Livermore Software Technology Corporation, 2003: 818
[18] Mandal S, Rice J, Elmustafa A A. J Mater Process Technol, 2008; 203: 401 |
| No Suggested Reading articles found! |
|
|
Viewed |
|
|
|
Full text
|
|
|
|
|
Abstract
|
|
|
|
|
Cited |
|
|
|
|
| |
Shared |
|
|
|
|
| |
Discussed |
|
|
|
|
