Please wait a minute...
金属学报  2026, Vol. 62 Issue (10): 1702-1712    DOI: 10.11900/0412.1961.2024.00445
  研究论文 本期目录 | 过刊浏览 |
粉末特征对激光粉末床熔融制备可降解Zn-Mn-Mg合金组织与力学性能的影响
黄成聪1,2, 李亚庚1,2(), 王鲁宁1,2()
1 北京科技大学 材料科学与工程学院 北京材料基因组高精尖创新中心 北京 100083
2 辽宁材料实验室 材料智能技术研究所 沈阳 110004
Effects of Powder Morphology on Microstructure Evolution and Mechanical Properties of Laser Powder Bed Fusion Degradable Zn-Mn-Mg Alloy
HUANG Chengcong1,2, LI Yageng1,2(), WANG Luning1,2()
1 Beijing Advanced Innovation Center for Materials Genome Engineering, School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083, China
2 Institute of Materials Intelligent Technology, Liaoning Academy of Materials, Shenyang 110004, China
引用本文:

黄成聪, 李亚庚, 王鲁宁. 粉末特征对激光粉末床熔融制备可降解Zn-Mn-Mg合金组织与力学性能的影响[J]. 金属学报, 2026, 62(10): 1702-1712.
Chengcong HUANG, Yageng LI, Luning WANG. Effects of Powder Morphology on Microstructure Evolution and Mechanical Properties of Laser Powder Bed Fusion Degradable Zn-Mn-Mg Alloy[J]. Acta Metall Sin, 2026, 62(10): 1702-1712.

全文: PDF(2444 KB)   HTML
摘要: 

低熔点锌基合金在激光粉末床熔融(LPBF)过程中蒸发飞溅严重,导致成形质量下降,优化粉末形貌和粒径是改善这一问题的有效措施。本工作通过电极感应气体雾化(EIGA)和等离子旋转电极(PREP)方法制备了两种具有不同形貌和粒径的Zn-Mn-Mg合金粉末,并采用LPBF技术制备合金块体,比较了两种粉末的成形工艺窗口,研究了粉末形貌和粒径对LPBF制备锌合金微观组织和力学性能的影响。结果表明,由 PREP方法制备的粉末具有更优的球形度和较大的粒径,相较于EIGA方法制备的粉末,其在LPBF过程中表现出更宽的优质成形工艺窗口。在LPBF成形工艺参数为激光功率P = 50 W、扫描速率V = 600 mm/s时,PREP方法制备粉末所得的成形锌合金块体具有更致密的微观组织和更小的晶粒尺寸。成形的两种块体试样的拉伸屈服强度(约210 MPa)和抗拉强度(约285 MPa)无显著差异,但EIGA + LPBF方法制备的块体试样的压缩屈服强度((288.2 ± 4.3) MPa)略高于PREP + LPBF方法制备的块体试样((258.5 ± 3.5) MPa)。PREP + LPBF方法制备的块体试样的拉伸延伸率(21.8% ± 2.3%)显著高于EIGA + LPBF方法制备的块体试样(3.3% ± 0.7%),塑性差异可能归因于PREP方法制备粉末在LPBF过程中具有更均匀的热传导和应变分布。

关键词 : 增材制造,  锌合金,  粉末特征,  力学性能    
Abstract:

Zinc-based alloys are emerging as the next generation of degradable metals due to their favorable degradation rates. Additive manufacturing offers the capability to produce personalized structures, making it a promising method for generating biomedical metal components. However, during laser powder bed fusion (LPBF), zinc-based alloys can experience significant evaporation because of their low melting point, which often results in poor surface quality. Optimizing powder morphology and particle size present a potential strategy to enhance forming quality. In this study, two Zn-1Mn-0.4Mg (mass fraction, %) alloy powders with particle sizes of 15-53 μm and 30-75 μm were produced using electrode induction gas atomization (EIGA) and the plasma rotating electrode process (PREP), respectively. Bulk alloys were fabricated using LPBF, and the processing windows for both powders were compared to investigate the effects of powder morphology and particle size on the microstructural and mechanical properties. The results indicated that PREP powders, which exhibited better sphericity and larger particle size, had a broader and more stable LPBF processing window. This led to bulk samples with higher density and smaller grain sizes compared to those prepared with EIGA powders. Under the processing parameters of laser power P = 50 W and scanning rate V = 600 mm/s, both bulk sample types displayed similar tensile yield strength (~210 MPa) and ultimate tensile strength (~285 MPa). However, the compressive yield strength of the EIGA + LPBF samples ((288.2 ± 4.3) MPa) was slightly higher than that of the PREP + LPBF samples ((258.5 ± 3.5) MPa). By contrast, the PREP + LPBF samples demonstrated significantly greater tensile elongation (21.8% ± 2.3%) compared to the EIGA + LPBF samples (3.3% ± 0.7%). This enhanced ductility was primarily attributed to the more homogeneous thermal conductivity and strain distribution in PREP powders during the LPBF process.

Key words: additive manufacturing    zinc alloy    powder characteristics    mechanical property
收稿日期: 2024-12-28     
ZTFLH:  TG 146.1  
基金资助:国家重点研发计划项目(2023YFB3813000);国家自然科学基金项目(52471260);国家自然科学基金项目(52201294)
通讯作者: 李亚庚,yagengli@ustb.edu.cn,主要从事增材制造及生物医用材料研究;
王鲁宁,luning.wang@ustb.edu.cn,主要从事生物医用材料研究
Corresponding author: LI Yageng, associate professor, Tel: (010)62332609, E-mail: yagengli@ustb.edu.cn;
WANG Luning, professor, Tel: (010)62332609, E-mail: luning.wang@ustb.edu.cn
作者简介: 黄成聪,男,1995年生,博士生
MethodZnMnMgO
EIGA98.560.920.43< 0.1
PREP98.560.970.38< 0.1
表1  使用电极感应气体雾化(EIGA)和等离子旋转电极(PREP)方法制备的Zn-Mn-Mg合金粉末的化学成分 (mass fraction / %)
图1  EIGA和PREP方法制备的Zn-Mn-Mg合金粉末的SEM像和尺寸分布
图2  EIGA方法制备的合金粉末经不同激光粉末床熔融(LPBF)工艺成形后的块体试样的致密度等高线图和OM像
图3  PREP方法制备的合金粉末经不同LPBF工艺成形后的块体试样的致密度等高线图和OM像
图4  EIGA和PREP方法制备的合金粉末经LPBF工艺(扫描功率P = 50 W、扫描速率V = 600 mm/s)成形后块体试样的XRD谱
图5  EIGA和PREP方法制备的合金粉末经LPBF工艺(P = 50 W、 V = 600 mm/s)成形后块体试样的OM像、EPMA像及Mn、Mg和O元素分布
图6  EIGA和PREP方法制备的合金粉末经LPBF工艺(P = 50 W、 V = 600 mm/s)成形后块体试样的反极图、极图和局部取向差分布图
图7  EIGA和PREP方法制备的合金粉末经LPBF工艺(P = 50 W、 V = 600 mm/s)成形后块体试样的拉伸和压缩应力-应变曲线
图8  EIGA和PREP方法制备的合金粉末经LPBF工艺(P = 50 W、 V = 600 mm/s)成形后块体试样拉伸断口的SEM像
图9  PREP + LPBF方法制备的块体试样的TEM分析
[1] Kabir H, Munir K, Wen C E, et al. Recent research and progress of biodegradable zinc alloys and composites for biomedical applications: Biomechanical and biocorrosion perspectives[J]. Bioact. Mater., 2021, 6: 836
doi: 10.1016/j.bioactmat.2020.09.013 pmid: 33024903
[2] Li Y G, Shi Y X, Lu Y C, et al. Additive manufacturing of vascular stents[J]. Acta Biomater., 2023, 167: 16
doi: 10.1016/j.actbio.2023.06.014 pmid: 37331614
[3] Mostaed E, Sikora-Jasinska M, Drelich J W, et al. Zinc-based alloys for degradable vascular stent applications[J]. Acta Biomater., 2018, 71: 1
doi: S1742-7061(18)30125-9 pmid: 29530821
[4] Qi X H, Liang X K, Wang J H, et al. Microstructure tailoring in laser powder bed fusion (L-PBF): Strategies, challenges, and future outlooks[J]. J. Alloys Compd., 2024, 970: 172564
doi: 10.1016/j.jallcom.2023.172564
[5] Clare A T, Mishra R S, Merklein M, et al. Alloy design and adaptation for additive manufacture[J]. J. Mater. Process. Technol., 2022, 299: 117358
doi: 10.1016/j.jmatprotec.2021.117358
[6] Bose S, Ke D X, Sahasrabudhe H, et al. Additive manufacturing of biomaterials[J]. Prog. Mater. Sci., 2018, 93: 45
doi: 10.1016/j.pmatsci.2017.08.003 pmid: 31406390
[7] Zheng Y F, Xia D D, Shen Y N, et al. Additively manufactured biodegradable metal implants[J]. Acta Metall. Sin., 2021, 57: 1499
[7] 郑玉峰, 夏丹丹, 谌雨农 等. 增材制造可降解金属医用植入物[J]. 金属学报, 2021, 57: 1499
doi: 10.11900/0412.1961.2021.00294
[8] Li Y G, Jahr H, Zhou J, et al. Additively manufactured biodegradable porous metals[J]. Acta Biomater., 2020, 115: 29
doi: S1742-7061(20)30478-5 pmid: 32853809
[9] Kassym K, Perveen A. Atomization processes of metal powders for 3D printing[J]. Mater. Today: Proc., 2020, 26: 1727
[10] Zhao X M, Chen J, Lin X, et al. Study on microstructure and mechanical properties of laser rapid forming Inconel 718[J]. Mater. Sci. Eng., 2008, A478: 119
[11] Tammas-Williams S, Withers P J, Todd I, et al. Porosity regrowth during heat treatment of hot isostatically pressed additively manufactured titanium components[J]. Scr. Mater., 2016, 122: 72
doi: 10.1016/j.scriptamat.2016.05.002
[12] Spierings A B, Herres N, Levy G. Influence of the particle size distribution on surface quality and mechanical properties in AM steel parts[J]. Rapid Prototyping J., 2011, 17: 195
doi: 10.1108/13552541111124770
[13] Abd-Elghany K, Bourell D L. Property evaluation of 304L stainless steel fabricated by selective laser melting[J]. Rapid Prototyping J., 2012, 18: 420
doi: 10.1108/13552541211250418
[14] Baitimerov R, Lykov P, Zherebtsov D, et al. Influence of powder characteristics on processability of AlSi12 alloy fabricated by selective laser melting[J]. Materials, 2018, 11: 742
doi: 10.3390/ma11050742
[15] Bi Z N, Zhang P, Zhang H P. Effect of metal powder characteristics on metallurgical quality of laser powder bed fusion additive manufacturing[J]. Powder Metall. Ind., 2024, 34(6): 1
[15] 毕中南, 张 鹏, 张浩鹏. 金属粉末特征对激光粉末床熔融成形质量的影响[J]. 粉末冶金工业, 2024, 34(6): 1
[16] Qin F, Shi Q, Zhou G, et al. Influence of powder particle size distribution on microstructure and mechanical properties of 17-4 PH stainless steel fabricated by selective laser melting[J]. J. Mater. Res. Technol., 2023, 25: 231
doi: 10.1016/j.jmrt.2023.05.241
[17] Shi Z Z, Yu J, Liu X F. Microalloyed Zn-Mn alloys: From extremely brittle to extraordinarily ductile at room temperature[J]. Mater. Des., 2018, 144: 343
doi: 10.1016/j.matdes.2018.02.049
[18] Zhu X L, Ren T T, Guo P S, et al. Strengthening mechanism and biocompatibility of degradable Zn-Mn alloy with different Mn content[J]. Mater. Today Commun., 2022, 31: 103639
[19] Zheng Y Z, Huang C C, Li Y G, et al. Mimicking the mechanical properties of cortical bone with an additively manufactured biodegradable Zn-3Mg alloy[J]. Acta Biomater., 2024, 182: 139
doi: 10.1016/j.actbio.2024.05.023
[20] Li Z L, Zhang X L, Tian D K. Effect of multi-pass compression deformation on microstructure evolution of AZ80 magnesium alloy[J]. Acta Metall. Sin., 2024, 60: 311
doi: 10.11900/0412.1961.2022.00010
[20] 李振亮, 张欣磊, 田董扩. 多道次压缩变形对AZ80镁合金微观组织演化的影响[J]. 金属学报, 2024, 60: 311
doi: 10.11900/0412.1961.2022.00010
[21] Sangid M D, Ezaz T, Sehitoglu H. Energetics of residual dislocations associated with slip-twin and slip-GBs interactions[J]. Mater. Sci. Eng., 2012, A542: 21
[22] Chu F Z, Shen H P, Liu J W, et al. Improved ductility by reducing powder size in laser powder bed fusion of AlSi10Mg[J]. Addit. Manuf. Front., 2024, 3: 200122
[23] Zhang S S, Lane B, Whiting J, et al. On thermal properties of metallic powder in laser powder bed fusion additive manufacturing[J]. J. Manuf. Process., 2019, 47: 382
doi: 10.1016/j.jmapro.2019.09.012
[24] Gusarov A V, Yadroitsev I, Bertrand P, et al. Model of radiation and heat transfer in laser-powder interaction zone at selective laser melting[J]. J. Heat Transfer., 2009, 131: 072101
[25] Körner C, Attar E, Heinl P. Mesoscopic simulation of selective beam melting processes[J]. J. Mater. Process. Technol., 2011, 211: 978
doi: 10.1016/j.jmatprotec.2010.12.016
[26] Hosseini E, Popovich V A. A review of mechanical properties of additively manufactured Inconel 718[J]. Addit. Manuf., 2019, 30: 100877
[27] Farzadfar S A, Murtagh M J, Venugopal N. Impact of IN718 bimodal powder size distribution on the performance and productivity of laser powder bed fusion additive manufacturing process[J]. Powder Technol., 2020, 375: 60
doi: 10.1016/j.powtec.2020.07.092
[28] Coe H G, Pasebani S. Use of bimodal particle size distribution in selective laser melting of 316L stainless steel[J]. J. Manuf. Mater. Process., 2020, 4: 8
doi: 10.3390/jmmp4010008
[29] Qin Y, Liu J G, Chen Y Z, et al. Influence of laser energy input and shielding gas flow on evaporation fume during laser powder bed fusion of Zn metal[J]. Materials, 2021, 14: 2677
doi: 10.3390/ma14102677
[30] Ruan G, Liu C, Qu H Q, et al. A comparative study on laser powder bed fusion of IN718 powders produced by gas atomization and plasma rotating electrode process[J]. Mater. Sci. Eng., 2022, A850: 143589
[31] Brika S E, Letenneur M, Dion C A, et al. Influence of particle morphology and size distribution on the powder flowability and laser powder bed fusion manufacturability of Ti-6Al-4V alloy[J]. Addit. Manuf., 2020, 31: 100929
[32] Venezuela J, Dargusch M S. The influence of alloying and fabrication techniques on the mechanical properties, biodegradability and biocompatibility of zinc: A comprehensive review[J]. Acta Biomater., 2019, 87: 1
doi: S1742-7061(19)30055-8 pmid: 30660777
[33] Wu Y, Fu Q Y, Guo B S, et al. Revealing the mechanical and degradation properties of the Zn-Cu-Ti alloy with ununiform heterostructure[J]. Mater. Sci. Eng., 2022, A853: 143775
[34] Shi Z Z, Li X M, Yao S L, et al. 300 MPa grade biodegradable high-strength ductile low-alloy (BHSDLA) Zn-Mn-Mg alloys: An in vitro study[J]. J. Mater. Sci. Technol., 2023, 138: 233
doi: 10.1016/j.jmst.2022.08.015
[35] Yin D D, Boehlert C J, Long L J, et al. Tension-compression asymmetry and the underlying slip/twinning activity in extruded Mg-Y sheets[J]. Int. J. Plast., 2021, 136: 102878
doi: 10.1016/j.ijplas.2020.102878
[36] Long F, Kacher J, Yao Z W, et al. A tomographic TEM study of tension-compression asymmetry response of pyramidal dislocations in a deformed Zr-2.5Nb alloy[J]. Scr. Mater., 2018, 153: 94
doi: 10.1016/j.scriptamat.2018.04.043
[37] Chen C, Huang H, Niu J L, et al. Origin of high tension-compression yield asymmetry in as-extruded pure zinc[J]. Scr. Mater., 2021, 200: 113922
doi: 10.1016/j.scriptamat.2021.113922
[38] Chandra S, Wang C C, Tor S B, et al. Powder-size driven facile microstructure control in powder-fusion metal additive manufacturing processes[J]. Nat. Commun., 2024, 15: 3094
doi: 10.1038/s41467-024-47257-w
[1] 李帅雨, 刘泽栋, 杨劼人, 金伟, 彭博, 杜新, 周斯曼. TA18合金铸锭-管坯组织遗传行为及力学性能调控[J]. 金属学报, 2026, 62(9): 1487-1502.
[2] 刘泽田, 路伟昭, 徐新宇, 刘旭, 张少游, 王慧远. 均质化温度对3003铝合金微观组织和力学性能的影响规律[J]. 金属学报, 2026, 62(9): 1503-1516.
[3] 郭传平, 石尘尘, 刘鹏, 高冬芳, 赵洋洋, 乔阳. 基于机器学习的生物可降解锌合金力学性能预测[J]. 金属学报, 2026, 62(9): 1615-1626.
[4] 张雪, 梁静静, 赵玉淞, 章环, 穆亚航, 周亦胄, 孙晓峰, 李金国. 基于固溶元素增材制造镍基高温合金的成分设计[J]. 金属学报, 2026, 62(8): 1395-1404.
[5] 杨何, 侯自勇, 胡兴益, 程金骏, 王亚茹, 范国华, 黄晓旭. 超高强不锈钢微丝表征技术:进展与展望[J]. 金属学报, 2026, 62(7): 1189-1206.
[6] 王彬, 赵鹏, 刘家伟, 张春波, 秦志伟, 董红刚, 李鹏. 热处理对FGH96高温合金惯性摩擦焊接头微观组织演变及力学性能的影响[J]. 金属学报, 2026, 62(6): 1043-1058.
[7] 许鼎锋, 韩飞扬, 姜琦成, 王欢, 尚利媛, 卢一平. AlCrFeCoNi低膨胀合金的成分设计及组织和性能优化[J]. 金属学报, 2026, 62(6): 1021-1031.
[8] 吕昭平, 申耀祖, 王先珍, 陈强, 唐建国, 张晓宾, 于勇, 蒋虽合, 刘雄军, 王辉, 吴渊. 面向极端服役条件的高熵合金结构材料:性能优势、瓶颈与突破路径[J]. 金属学报, 2026, 62(5): 743-755.
[9] 史玉升, 程焜, 张程健, 卢佳浩, 李伟, 张李超, 魏青松, 蔡超. 难加工金属增材制造/热等静压融合成形研究现状与展望[J]. 金属学报, 2026, 62(5): 770-784.
[10] 郑玉峰, 谌雨农. 纯Mo及钼基可降解金属材料的研究现状与发展趋势[J]. 金属学报, 2026, 62(5): 905-922.
[11] 陈光, 陈奉锐, 朱德民, 李贵忠, 李罗, 宋伟东, 王子特, 相恒高, 陈旸, 祁志祥. 聚片孪生功能基元序构的高性能TiAl合金[J]. 金属学报, 2026, 62(4): 541-549.
[12] 王建峰, 许珍木, 刘战, 高转妮, 占小红. 超声振动对TC4钛合金窄间隙激光焊接组织及强化机理的影响[J]. 金属学报, 2026, 62(3): 406-420.
[13] 蒋志达, 胥杨洋, 于佳新, 刘文才, 朱浩文, 吴国华, 尚郑平. 高温无氧轧制Cu/1060Al/Cu三层复合材料的力学和导电性能[J]. 金属学报, 2026, 62(3): 431-444.
[14] 江国龙, 周霞. 超声辅助下Mg/Mg-Zn-Al钎焊界面行为的分子动力学模拟[J]. 金属学报, 2026, 62(2): 372-382.
[15] 李少杰, 金剑锋, 田艳中, 潘虎成, 王明涛, 秦高梧. 细观力学模拟双峰晶粒分布铜的异质变形诱导效应[J]. 金属学报, 2026, 62(10): 1687-1701.