Please wait a minute...
金属学报  2014, Vol. 50 Issue (3): 361-366    DOI: 10.3724/SP.J.1037.2013.00421
  本期目录 | 过刊浏览 |
预制件烧结温度对Bi(OH)3-Al18B4O33w/Al复合材料阻尼性能的影响*
刘刚1,2, 唐莎巍1, 胡津1()
1 哈尔滨工业大学材料科学与工程学院, 哈尔滨150001
2 哈尔滨理工大学应用科学学院, 哈尔滨150080
EFFECTS OF SINTERING TEMPERATURE OF WHISKER PREFORM ON THE DAMPING PROPERTIES OF BI(OH)3-COATED AL18B4O33 WHISKER-REINFORCED ALUMINUM COMPOSITES
LIU Gangsup1,2, TANG Shaweisup1, HU Jinsup1()
1 School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001
2 College of Applied Science, Harbin University of Science and Technology, Harbin 150080
引用本文:

刘刚, 唐莎巍, 胡津. 预制件烧结温度对Bi(OH)3-Al18B4O33w/Al复合材料阻尼性能的影响*[J]. 金属学报, 2014, 50(3): 361-366.
Gang LIU, Shawei TANG, Jin HU. EFFECTS OF SINTERING TEMPERATURE OF WHISKER PREFORM ON THE DAMPING PROPERTIES OF BI(OH)3-COATED AL18B4O33 WHISKER-REINFORCED ALUMINUM COMPOSITES[J]. Acta Metall Sin, 2014, 50(3): 361-366.

全文: PDF(6167 KB)   HTML
摘要: 

采用化学方法在Al18B4O33晶须表面涂覆Bi(OH)3, 对所制备的晶须预制件进行不同温度的烧结, 在晶须表面获得不同结构的涂层. 利用挤压铸造方法制备相应的纯铝基复合材料. 研究了烧结温度对复合材料微观组织和阻尼性能的影响. 结果表明: 晶须预制件烧结温度对涂覆复合材料界面微观组织和阻尼性能有显著影响, 当烧结温度为530及830 ℃时, 2种复合材料中均存在2个阻尼峰(位错阻尼与界面阻尼), 后者的阻尼在整个测试温度范围内最高; 当预制件烧结温度为1000 ℃时, 复合材料中仅存在一个界面阻尼峰, 产生这种现象的原因主要是由于它们的界面状态不同造成的.

关键词 Al18B4O33晶须Bi(OH)3涂层预制件烧结温度阻尼性能    
Abstract

In order to alter the overall properties of composites, the reinforcement coatings are commonly implemented to improve wetting behavior and prevent interfacial reaction. Unfortunately, few researches were emphasized on the effects of the sintering temperature of whisker preform (STWP) on the damping behavior of composites, especially whisker with coatings. In the present investigation, Al18B4O33 whisker was coated with Bi(OH)3 by a chemical method. The whisker preform was sintered at the different temperature. The coated whisker-reinforced aluminum matrix composites were fabricated through squeeze casting technique. The damping properties of the coated composites with the different STWP were presented and discussed. The results indicated that the microstructures of coatings on the whisker surfaces and at the interface in the coated composites are strongly dependent on STWP. There are two damping peaks in the coated composites (related to dislocation damping and interface damping), when STWP is 530 and 830 ℃, respectively. Only one interface damping peak occur in the coated composite when STWP is 1000 ℃. When STWP is 830 ℃, the highest damping capacity is obtained in the coated composite, which relate to a special interfacial structure.

Key wordsAl18B4O33 whisker    Bi(OH)3 coating    preform    sintering temperature    damping property
收稿日期: 2013-07-17     
ZTFLH:  TG142.7  
基金资助:* 黑龙江省教育厅基金资助项目12531114
作者简介: null

刘 刚, 男, 1980年生, 讲师

图1  
图2  
图3  
图4  
图5  
[1] Deo N, Vakil S. Scr Mater, 1999; 40: 791
[2] Starink M J, Wang P, Sinclair I, Gregson P J. Acta Mater, 1999; 47: 3841
[3] Updike C A, Bhagat R B, Pechersky M J, Amateau M F. J Miner Met Mater Soc, 1990; 42: 42
[4] Schaller R. J Alloys Compd, 2003; 355: 131
[5] Gu J H, Zhang X N, Gu M Y. J Alloys Compd, 2004; 381: 182
[6] Urea A, Rams J, Escalera M D, Sanchez M. Compos Sci Technol, 2005; 65: 2025
[7] Campo M, Urea A, Rams J. Scr Mater, 2005; 52: 977
[8] Mandala D, Duttab B K, Panigrahib S C. Mater Sci Eng, 2008; A492: 346
[9] Davidson A M, Regener D. Compos Sci Technol, 2000; 60: 865
[10] Wu R J. Composite Materials. Taijin: Tianjin University Press, 2000: 385
[10] (吴人洁. 复合材料. 天津: 天津大学出版社, 2000: 385)
[11] Mandala D, Duttab B K, Panigrahib S C. Mater Sci Eng, 2008; A492: 346
[12] Ruiz-Navas E M, Delgado M L, Trindade B. Composites Part A, 2009; 40: 1283
[13] Li Z J, Fei W D, Wang L D. Compos Sci Technol, 2007; 67: 963
[14] Feldhoff A, Pippel E, Woltersdorf J. Adv Eng Mater, 2002; 2: 471
[15] Davidson A M, Regener D A. Compos Sci Technol, 2000; 60: 865
[16] Zhang X N, Wu R J, Li X C. Guo Z X . Sci China, 2002; 32E: 14
[16] (张小农, 吴人洁, 李小璀, Guo Z X. 中国科学, 2002; 32E: 14)
[17] Hu J, Wang X F. Compos Sci Technol, 2008; 68: 2297
[18] Liu G, Hu J. Mater Sci Eng, 2010; A527: 5136
[19] Liu G, Hu J. Powder Technol, 2012; 218: 124
[20] Liu G, Tang S W, Hu J. Mater Sci Eng, 2011; A528: 5184
[21] Mondolfo L F. Aluminum Alloys: Structure and Properties. London: Butter Worths/Boston Press, 1976: 80
[22] Hu J, Luo R S, Fei W D, Yao C K. J Mater Sci Lett, 1999; 18: 1525
[23] Zhang J, Perez R J, Lavernia E J. J Mater Sci, 1993; 28: 835
[24] Fan G H, Geng L, Zheng Z Z, Wang G S. Scr Mater, 2008; 59: 534
[25] Pan J, Lee S P, Yoshida M, Sasaki G, Fuyama N, Fujii T, Fukunaga H. Adv Compos Mater, 2001; 10: 299
[1] 王玉, 胡斌, 刘星毅, 张浩, 张灏云, 官志强, 罗海文. 退火温度对含Nb高锰钢力学和阻尼性能的影响[J]. 金属学报, 2021, 57(12): 1588-1594.
[2] 王世宏, 李健, 柴锋, 罗小兵, 杨才福, 苏航. 固溶温度对Fe-19Mn合金的γε相变和阻尼性能的影响[J]. 金属学报, 2020, 56(9): 1217-1226.
[3] 姚彦桃, 陈礼清, 王文广. 原位反应浸渗法制备(B4C+Ti)混杂增强Mg及AZ91D复合材料及其阻尼性能[J]. 金属学报, 2019, 55(1): 141-148.
[4] 胡小锋,杜瑜宾,闫德胜,戎利建. Cu的析出及其对FeCrMoCu合金阻尼性能和力学性能的影响[J]. 金属学报, 2017, 53(5): 601-608.
[5] 刘刚 孙雅丽 胡津 周科. Bi2O3涂覆Al18B4O33晶须增强铝基复合材料的阻尼性能[J]. 金属学报, 2010, 46(8): 979-983.
[6] 刘树伟 李秀艳 闫德胜 戎利建. 时效温度及微量Zr+Si对Zn--22\%Al合金阻尼性能的影响[J]. 金属学报, 2009, 45(9): 1099-1105.
[7] 胡小锋 李秀艳 张波 戎利建 李依依. Nb, Ti和Cu对Fe--13Cr--2.5Mo合金阻尼与腐蚀性能的影响[J]. 金属学报, 2009, 45(6): 717-722.
[8] 肖甫 赵新青 徐惠彬 姜海昌 戎利建. (NiTi)50-0.5xNbx形状记忆合金的阻尼性能及力学性能[J]. 金属学报, 2009, 45(1): 18-24.
[9] 林仁荣; 刘芳; 曹名洲; 杨锐 . 退火及置换元素对Fe-Cr-Al基合金阻尼性能及强度的影响[J]. 金属学报, 2005, 41(9): 958-962 .
[10] 秦孝华; 范存淦; 韩维新; 戎利建; 李依依 . 液态机械搅拌法制备陶瓷颗粒增强铝基复合材料[J]. 金属学报, 2002, 38(8): 885-887 .
[11] 王卫国; 周邦新 . 铁磁合金中的磁弹转换[J]. 金属学报, 2000, 36(1): 81-86 .
[12] 王卫国;周邦新;郑忠民. Fe—Cr—Al—Si合金阻尼性能研究[J]. 金属学报, 1998, 34(10): 1039-1042.
[13] 程饴萱;陈继勤;方晓旻;吕卫平. CuZnAl合金的马氏体及其相变的阻尼性能[J]. 金属学报, 1991, 27(3): 56-60.