Please wait a minute...
金属学报  2026, Vol. 62 Issue (9): 1487-1502    DOI: 10.11900/0412.1961.2025.00364
  研究论文 本期目录 | 过刊浏览 |
TA18合金铸锭-管坯组织遗传行为及力学性能调控
李帅雨1, 刘泽栋1, 杨劼人1(), 金伟2, 彭博1, 杜新1, 周斯曼1
1 四川大学 材料科学与工程学院 成都 610065
2 中国科学院金属研究所 师昌绪先进材料创新中心 沈阳 110016
Microstructural Inheritance Behavior and Mechanical Property Control of TA18 Alloy From Ingot to Tube Blank
LI Shuaiyu1, LIU Zedong1, YANG Jieren1(), JIN Wei2, PENG Bo1, DU Xin1, ZHOU Siman1
1 College of Materials Science and Engineering, Sichuan University, Chengdu 610065, China
2 Shi -changxu Innovation Center for Advanced Materials, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016, China
引用本文:

李帅雨, 刘泽栋, 杨劼人, 金伟, 彭博, 杜新, 周斯曼. TA18合金铸锭-管坯组织遗传行为及力学性能调控[J]. 金属学报, 2026, 62(9): 1487-1502.
Shuaiyu LI, Zedong LIU, Jieren YANG, Wei JIN, Bo PENG, Xin DU, Siman ZHOU. Microstructural Inheritance Behavior and Mechanical Property Control of TA18 Alloy From Ingot to Tube Blank[J]. Acta Metall Sin, 2026, 62(9): 1487-1502.

全文: PDF(5385 KB)   HTML
摘要: 

微观组织遗传性是实现TA18合金微观组织和性能调控的基础。本工作以TA18合金铸锭、不同规格锻棒、挤压管坯为研究对象,研究了从铸锭到管坯全流程中微观组织和织构演变的遗传规律及其对力学性能的影响,旨在为多尺度微观组织与性能的一体化控制提供指导。结果表明,从铸锭到管坯成型全流程,其组织遗传特征主要分为三类。(1) 微米级晶粒尺寸和等轴α相组织形貌在粗锻阶段建立后,在后续工序中被稳定遗传,晶粒细化是轴向抗拉强度从400 MPa提升至550 MPa以及延伸率提高的基础。(2) 小角度晶界(LAGB)占比的遗传呈现动态演化。粗锻与精锻阶段的高LAGB占比遗传贡献了加工硬化,但损害塑性;挤压阶段通过动态再结晶实现LAGB低占比遗传,塑性得以恢复。(3) 晶体学织构的遗传受多重因素控制。铸锭中心区域的{0001}//AD (轴向)基面织构与<101¯0>//AD织构在后续加工过程中被强烈遗传,且<101¯0>//AD织构强度持续增加;α相的c轴取向随工艺发生受控演变:粗锻后呈随机分布,精锻后转为径向织构,挤压后则形成周向织构。TA18合金通过原始组织的晶体取向、变形、动态再结晶机制的竞争与协同,耦合控制晶体学取向的遗传与演化,可通过对有益遗传(细晶、有利织构)的强化与有害遗传(高LAGB占比、不利织构)的阻断进行一体化设计,获得兼具高强度与良好塑性的TA18合金管坯。

关键词 : TA18合金,  组织遗传,  织构,  力学性能调控    
Abstract:

In metallic material processing, the microstructural and textural characteristics developed during each manufacturing stage establish the structural foundation for subsequent processing operations, creating substantial hereditary effects throughout the multistage manufacturing chain. This progressive, cross-process accumulation of microstructural and textural evolution makes precise tracing and effective control of microstructural inheritance pathways particularly complex during full-scale manufacturing from the initial ingot to the final TA18 tube blank. Microstructural inheritance forms the basis for structural design and property optimization in TA18 alloys. This investigation employed a 700-mm diameter TA18 alloy ingot as the starting material. The thermomechanical processing route comprised three stages: initial multipass forging in the β-phase field (1150-950 oC) followed by forging in the α + β phase field at 900 oC to produce a 170-mm diameter rough-forged bar; subsequent processing of the rough-forged bar in the two-phase region at 850 oC to obtain a 125-mm diameter finish-forged bar; finally, peeling, drilling, and canned hot extrusion of the finish-forged bar to fabricate tube blanks with inner and outer diameters of 28 and 42 mm, respectively. This study systematically investigates the hereditary evolution of microstructure and texture throughout the processing route from ingot to tube blank in the TA18 alloy and evaluates its impact on mechanical properties to guide the integrated control of multiscale microstructure and performance. The results demonstrate that microstructural hereditary characteristics can be categorized into three primary types. (1) Once established during rough forging, the micron-scale grain size and equiaxed α-phase morphology remain stably inherited in subsequent processing stages. Grain refinement serves as the fundamental basis for increasing axial tensile strength from 400 MPa to 550 MPa and improving elongation. (2) The inheritance of low angle grain boundary (LAGB) fraction exhibits dynamic evolution. The high fraction inherited during the rough- and finish-forging stages contributes to work hardening but negatively affects plasticity; in contrast, the low fraction inherited after extrusion, achieved via dynamic recrystallization, results in plasticity recovery. (3) The inheritance of crystallographic texture is governed by multiple competing mechanisms. The {0001}//axial direction (AD) basal texture and the <101¯0>//AD texture originating from the central region of the ingot are strongly inherited during subsequent processing, with the intensity of the <101¯0>//AD texture continuously increasing. The c-axis orientation of the α-phase undergoes controlled evolution during processing: it is randomly distributed after rough forging, transforms into a radial texture after finish forging, and finally develops into a circumferential texture after extrusion. The TA18 alloy controls the inheritance and evolution of crystallographic orientation through the competition and synergy of various mechanisms, including initial crystallographic orientation, deformation, and dynamic recrystallization. The integrated design of TA18 alloy tube blanks, possessing high strength and good plasticity can be achieved by reinforcing beneficial hereditary features (such as fine grains and favorable texture) and interrupting harmful features (such as high LAGB fraction and unfavorable texture).

Key words: TA18 alloy    microstructural inheritance    texture    mechanical property control
收稿日期: 2025-11-12     
ZTFLH:  TG306  
基金资助:国家重点研发计划项目(2023YFB3710700)
通讯作者: 杨劼人,yangjieren@scu.edu.cn,主要从事钛合金、贵金属及其凝固加工研究
Corresponding author: YANG Jieren, professor, Tel: 15881010703, E-mail: yangjieren@scu.edu.cn
作者简介: 李帅雨,男,2002年生,硕士生
图1  TA18合金加工流程示意图和拉伸样品尺寸
图2  TA18合金铸锭不同位置和多阶段热加工后微观组织的OM像、SEM像和EDS元素面扫描图
PointTiAlV
194.952.952.10
286.711.8911.40
表1  图2k1中点1和2的EDS点扫描结果 (mass fraction / %)
图3  TA18合金铸锭不同位置和多阶段热加工后的EBSD取向图、极图和反极图
图4  TA18合金铸锭不同位置和多阶段热加工后的晶界图、局部取向差图及其分布、大/小角度晶界占比和取向差角分布图
图5  TA18合金铸锭不同位置和多阶段热加工后的工程应力-应变曲线、力学性能对比和各强化机制对屈服强度的贡献
图6  TA18合金铸锭不同部位与多阶段热加工后断口形貌的SEM像
图7  微观组织演变与遗传链示意图
图8  TA18合金热加工过程中的EBSD分析和晶体取向演变示意图
[1] Najafizadeh M, Yazdi S, Bozorg M, et al. Classification and applications of titanium and its alloys: A review [J]. J. Alloys Compd. Commun., 2024, 3: 100019
[2] Alabort E, Tang Y T, Barba D, et al. Alloys-by-design: A low-modulus titanium alloy for additively manufactured biomedical implants [J]. Acta Mater., 2022, 229: 117749
doi: 10.1016/j.actamat.2022.117749
[3] Xu W C, Tong X Y, Wang Y Q, et al. Research progress on the influence of the deep-sea environment on the stress corrosion of titanium alloys [J]. Acta Metall. Sin., 2025, 61: 1469
doi: 10.11900/0412.1961.2024.00221
[3] 徐玮辰, 佟向瑜, 王优强 等. 深海环境对钛合金应力腐蚀影响的研究进展 [J]. 金属学报, 2025, 61: 1469
doi: 10.11900/0412.1961.2024.00221
[4] Yang Z K, Wu J J, Wang M Y, et al. Tensile deformation behavior of high-strength TA18 titanium alloy tube under warm forming conditions and constitutive model based on dislocation density [J]. Mater. Today Commun., 2023, 37: 107336
[5] Cheng Z H, Abd El-Aty A, Zhang R S X, et al. Finite element modeling and experimental investigation on manufacturing TA18 alloy pipes via hot free bending forming technology: Forming characteristics and process optimization [J]. J. Mater. Res. Technol., 2024, 29: 5225
doi: 10.1016/j.jmrt.2024.02.187
[6] He S T, Zeng W D, Xu J W, et al. The texture evolution related to the interactions between α and β phases in dual-phase region annealing of a near α titanium alloy pipe after Pilger cold rolling [J]. J. Alloys Compd., 2022, 890: 161807
doi: 10.1016/j.jallcom.2021.161807
[7] Lu S L, Zhang Z J, Liu R, et al. Optimal tensile properties of laser powder bed fusion hereditary basket-weave microstructure in additive manufactured Ti6Al4V [J]. Addit. Manuf., 2022, 59: 103092
[8] Sun Z Y, Mo X F, Li Y F, et al. Effects of hot isostatic pressing parameters on microstructure and properties of TA15 titanium alloy [J]. Spec. Cast. Nonferrous Alloys, 2023, 43: 804
[8] 孙志雨, 莫晓飞, 李亚峰 等. 热等静压工艺参数对TA15钛合金组织及性能的影响 [J]. 特种铸造及有色合金, 2023, 43: 804
[9] Wang C Y, Wang Y H, Li Y, et al. Effect of texture inheritance on microstructure of beta C titanium alloy [J]. Rare Met. Mater. Eng., 2023, 52: 3382
[9] 王春阳, 王玉会, 李 野 等. TB9钛合金棒材组织遗传效应与性能(英文) [J]. 稀有金属材料与工程, 2023, 52: 3382
[10] Qin X Y, Liu H, Chen Y Y, et al. Optimization in strength-ductility of Mg-Gd-Y-Zn-Al alloy through microstructural heredity process regulation [J]. Mater. Sci. Eng., 2025, A944: 148930
[11] Chen Q Y, Zhang W N, Tang S, et al. Microstructural heredity of Ni-containing cryogenic steel and its effect on the toughness at 77 K [J]. Mater. Sci. Eng., 2022, A832: 142441
[12] Cheng X, Gao G H, Fu C, et al. Mechanistic understanding of banded microstructure and its effect on anisotropy of toughness in low carbon-low alloy steel [J]. Mater. Sci. Eng., 2025, A919: 147507
[13] Azizi N, Mahmudi R. Microstructure, texture, and mechanical properties of the extruded and multi-directionally forged Mg-xGd alloys [J]. Mater. Sci. Eng., 2021, A817: 141385
[14] Semiatin S L. An overview of the thermomechanical processing of α/β titanium alloys: Current status and future research opportunities [J]. Metall. Mater. Trans., 2020, 51A: 2593
[15] Chen P, Li J S, Li C C, et al. Research on the hot-temperature rheological behavior and microstructural evolution of TA18 titanium alloy [J]. Mater. Today Commun., 2025, 43: 111810
[16] Wang Z L, Wang L, Zhang S Y, et al. Analytical springback modelling for thermal-mechanical bending of TA18 tube under non-isothermal loading [J]. Appl. Math. Model., 2025, 143: 115964
doi: 10.1016/j.apm.2025.115964
[17] Zhao Z B, Tan H B, Zhang B H, et al. Review: Microtextures in near α and α + β dual-phase titanium alloys [J]. Acta Metall. Sin., 2026, 62: 275
[17] 赵子博, 谭海兵, 张博华 等. 综述: 近α型和α + β两相钛合金的微织构 [J]. 金属学报, 2026, 62: 275
doi: 10.11900/0412.1961.2024.00449
[18] Liang C Z, Wang J, Xu J F, et al. High-temperature tensile deformation behavior and damage model of TB6 alloy [J]. J. Inn. Mong. Univ. Technol. Nat. Sci. Ed., 2024, 43: 434
[18] 梁春祖, 王 静, 许江帆 等. TB6钛合金高温拉伸变形过程临界损伤模型 [J]. 内蒙古工业大学学报(自然科学版), 2024, 43: 434
[19] Wang B, Li R, Liu J L. Grain refinement of ZALSi7Mg1 alloy by structure heredity [J]. Found. Technol., 2009, 30: 779
[19] 王 斌, 李 日, 刘军利. 利用组织遗传性细化ZAlSi7Mg1合金晶粒的研究 [J]. 铸造技术, 2009, 30: 779
[20] Jing Z Q, Sun Y H, Song S C. Numerical simulation of macrosegregation heredity on TC4 titanium alloy ingot by vacuum arc remelting [J]. Metall. Res. Technol., 2023, 120: 116
doi: 10.1051/metal/2023012
[21] Li D, Huang H L, Chen C, et al. Additive manufacturing of high strength near β titanium alloy Ti-55511 by engineering nanoscale secondary α laths via in-situ heat treatment [J]. Mater. Sci. Eng., 2021, A814: 141245
[22] He S H, He B B, Zhu K Y, et al. On the correlation among dislocation density, lath thickness and yield stress of bainite [J]. Acta Mater., 2017, 135: 382
doi: 10.1016/j.actamat.2017.06.050
[23] Zhang Y, Li D S, Li X Q, et al. Creep deformation and strength evolution mechanisms of a Ti-6Al-4V alloy during stress relaxation at elevated temperatures from elastic to plastic loading [J]. J. Mater. Sci. Technol., 2022, 126: 93
doi: 10.1016/j.jmst.2022.02.042
[24] Sun Y G, Zhang C J, Feng H, et al. Dynamic recrystallization mechanism and improved mechanical properties of a near α high temperature titanium alloy processed by severe plastic deformation [J]. Mater. Charact., 2020, 163: 110281
doi: 10.1016/j.matchar.2020.110281
[25] Fan X G, Yang H, Gao P F. Prediction of constitutive behavior and microstructure evolution in hot deformation of TA15 titanium alloy [J]. Mater. Des., 2013, 51: 34
doi: 10.1016/j.matdes.2013.03.103
[26] Matsumoto H, Velay V. Mesoscale modeling of dynamic recrystallization behavior, grain size evolution, dislocation density, processing map characteristic, and room temperature strength of Ti-6Al-4V alloy forged in the (α + β) region [J]. J. Alloys Compd., 2017, 708: 404
doi: 10.1016/j.jallcom.2017.02.285
[27] Yang G J, Park S J. Deformation of single crystals, polycrystalline materials, and thin films: A review [J]. Materials, 2019, 12: 2003
doi: 10.3390/ma12122003
[28] Zhou Z C, Jiang B B, Qiu J K, et al. Phase interface-induced dwell fatigue cracks in titanium alloy with lamellar microstructure [J]. Sci. China Mater., 2023, 66: 4267
doi: 10.1007/s40843-023-2641-7
[28] 周志春, 江彬彬, 邱建科 等. 片层组织钛合金中相界面诱导保载疲劳裂纹形成(英文) [J]. 中国科学: 材料科学(英文版), 2023, 66: 4267
[29] Burtscher M, Alfreider M, Schmuck K, et al. In situ fracture observations of distinct interface types within a fully lamellar intermetallic TiAl alloy [J]. J. Mater. Res., 2021, 36: 2465
doi: 10.1557/s43578-020-00088-z
[30] Duan C Z, Zhang L C, Li H H, et al. Ductile fracture due to adiabatic shear during the serrated chip formation in high speed cutting: A microscopic investigation [J]. Key Eng. Mater., 2011, 467-469: 181
doi: 10.4028/www.scientific.net/KEM.467-469
[31] Zhang M C, Xu Q S, Liu Y, et al. Effect of hot-pressing temperature on the microstructure and properties of the diffusion-bonded region of TC4 alloy [J]. Acta Metall. Sin., 2025, 61: 1183
doi: 10.11900/0412.1961.2023.00414
[31] 张洺川, 徐勤思, 刘 意 等. 热压温度对TC4合金扩散连接区组织与性能的影响 [J]. 金属学报, 2025, 61: 1183
doi: 10.11900/0412.1961.2023.00414
[32] Wang K, Li H H, Zhou Y, et al. Dislocation slip and crack nucleation mechanism in dual-phase microstructure of titanium alloys: A review [J]. Acta Metall. Sin. (Engl. Lett.), 2023, 36: 353
doi: 10.1007/s40195-022-01505-4
[33] Fan X G, Zeng X, Yang H, et al. Deformation banding in β working of two-phase TA15 titanium alloy [J]. Trans. Nonferrous Met. Soc. China, 2017, 27: 2390
doi: 10.1016/S1003-6326(17)60265-6
[34] Chen G X. Microscopic deformation behavior of Ti-6Ai-4V titanium alloy based on the characteristic of two phase [D]. Qinhuangdao: Yanshan University, 2018
[34] 陈国兴. 基于双相特征的Ti-6Al-4V钛合金微观变形行为研究 [D]. 秦皇岛: 燕山大学, 2018
[35] Chen Y T, Wang K, Ren Z. Interaction between phase transformation and static recrystallization during annealing of rolled TC18 titanium alloy [J]. J. Mater. Sci. Technol., 2024, 202: 1
doi: 10.1016/j.jmst.2024.03.011
[36] Li Y L, Fang H Z, Chen R R, et al. A comparative analysis of a unique DRX process in achieving a homogeneous distribution of β grains in the single phase region of as-cast Ti644321 alloy [J]. Mater. Charact., 2024, 207: 113505
doi: 10.1016/j.matchar.2023.113505
[37] Li H Z, Wu D P, Jiang H J, et al. Dynamic recrystallization mechanism and model of TC31 titanium alloy sheet during hot deformation [J]. J. Mater. Res., 2025, 40: 1877
doi: 10.1557/s43578-025-01620-9
[38] Yang Q Y, Ma M, Tan Y B, et al. Microstructure and texture evolution of TB8 titanium alloys during hot compression [J]. Rare Met., 2021, 40: 2917
doi: 10.1007/s12598-020-01643-7
[39] Rios P R, Siciliano Jr F, Sandim H R Z, et al. Nucleation and growth during recrystallization [J]. Mater. Res., 2005, 8: 225
doi: 10.1590/S1516-14392005000300002
[40] Hadadzadeh A, Mokdad F, Wells M A, et al. A new grain orientation spread approach to analyze the dynamic recrystallization behavior of a cast-homogenized Mg-Zn-Zr alloy using electron backscattered diffraction [J]. Mater. Sci. Eng., 2018, A709: 285
[41] Chen Y L, Jin L, Dong J, et al. Twinning effects on the hot deformation behavior of AZ31 Mg alloy [J]. Mater. Charact., 2016, 118: 363
doi: 10.1016/j.matchar.2016.06.014
[42] Huang K, Logé R E. A review of dynamic recrystallization phenomena in metallic materials [J]. Mater. Des., 2016, 111: 548
doi: 10.1016/j.matdes.2016.09.012
[43] Wang Y S, Li Z D, Wang H Y, et al. Flow behavior and dynamic recrystallization mechanism of a new near-alpha titanium alloy Ti-0.3Mo-0.8Ni-2Al-1.5Zr [J]. J. Mater. Res. Technol., 2024, 30: 3863
doi: 10.1016/j.jmrt.2024.04.076
[44] Xie B C, Zhang B Y, Yu H, et al. Nucleation mechanism of discontinuous dynamic recrystallization with restrained grain boundary sliding [J]. Met. Mater. Int., 2021, 27: 5476
doi: 10.1007/s12540-020-00847-x
[45] Qiang F M, Kou H C, Zhang Y D, et al. Crystallographic orientation related dynamic recrystallization behavior and its impact on texture development of high-temperature α phase in TiAl alloy [J]. J. Alloys Compd., 2025, 1010: 178066
doi: 10.1016/j.jallcom.2024.178066
[46] Burgers W G. On the process of transition of the cubic-body-centered modification into the hexagonal-close-packed modification of zirconium [J]. Physica, 1934, 1: 561
doi: 10.1016/S0031-8914(34)80244-3
[47] Li J S, Tang B, Fan J K, et al. Deformation mechanism and microstructure control of high strength metastable β titanium alloy [J]. Acta Metall. Sin., 2021, 57: 1438
[47] 李金山, 唐 斌, 樊江昆 等. 高强亚稳β钛合金变形机制及其组织调控方法 [J]. 金属学报, 2021, 57: 1438
doi: 10.11900/0412.1961.2021.00352
[48] Guo B Q, Jonas J J. Dynamic transformation during the high temperature deformation of titanium alloys [J]. J. Alloys Compd., 2021, 884: 161179
doi: 10.1016/j.jallcom.2021.161179
[49] Shi R, Dixit V, Viswanathan G B, et al. Experimental assessment of variant selection rules for grain boundary α in titanium alloys [J]. Acta Mater., 2016, 102: 197
doi: 10.1016/j.actamat.2015.09.021
[50] Li H, Wei D, Zhang H Q, et al. Texture evolution and controlling of high-strength titanium alloy tube in cold pilgering for properties tailoring [J]. J. Mater. Process. Technol., 2020, 279: 116520
doi: 10.1016/j.jmatprotec.2019.116520
[51] Chatterjee R, Narayana Murty S V S, Alankar A. Dynamic recrystallization in titanium alloys: A comprehensive review [J]. Mater. Perform. Charact., 2020, 9: 1
[52] Hall E O. The deformation and ageing of mild steel: III Discussion of results [J]. Proc. Phys. Soc., 1951, 64B: 747
[53] Petch N J. The cleavage strength of polycrystals [J]. J. Iron Steel Inst., 1953, 174: 25
[54] Hémery S, Naït-Ali A, Smerdova O, et al. Deformation mechanisms in the α phase of the Ti-6Al-2Sn-4Zr-2Mo titanium alloy: In situ experiments and simulations [J]. Int. J. Plast., 2024, 175: 103947
doi: 10.1016/j.ijplas.2024.103947
[55] Spurr W F, Quist W E. The effects of crystallographic texture on the mechanical and fracture properties of Ti-3Al-2.5V hydraulic tubing [J]. SAE Trans., 1973, 82: 730515
[1] 陈园, 宫春波, 王胜刚, 马嵩, 张志东. 纳米晶304不锈钢板材的微观组织、显微硬度与耐腐蚀性能[J]. 金属学报, 2026, 62(9): 1566-1580.
[2] 邓偲瀛, 董家瑄, 陈帅峰, 宋鸿武, 张士宏. Zr-4合金带材冲制过程中的织构演变和变形机制:实验和宏微观耦合模拟研究[J]. 金属学报, 2026, 62(8): 1417-1426.
[3] 吴帆, 刘华辉, 边文珊, 蔡竣宇, 金士杰, 罗忠兵. TC4钛合金循环变形微观组织演化与滑移机制[J]. 金属学报, 2026, 62(6): 1082-1090.
[4] 常松涛, 张芳, 沙玉辉, 左良. 晶界偏聚元素Sb作用下无取向硅钢织构的空间分布与演变机制[J]. 金属学报, 2026, 62(4): 627-635.
[5] 赵子博, 谭海兵, 张博华, 刘玉敬, 刘建荣, 郭会明, 曾卫东, 田伟, 王清江. 综述:近 α 型和 α + β 两相钛合金的微织构[J]. 金属学报, 2026, 62(2): 275-288.
[6] 谭若涵, 宋永锋, 陈超, 李丹, 成庶, 李雄兵. 增材制造钛合金等效弹性张量的细观力学建模与实验研究[J]. 金属学报, 2025, 61(9): 1438-1448.
[7] 吴泽威, 颜俊雄, 胡励, 韩修柱. 双峰分离非基面织构AZ31镁合金板材反常中温轧制变形行为及机理[J]. 金属学报, 2025, 61(8): 1165-1173.
[8] 徐小严, 方超, 邱建科, 张蒙蒙, 史栋刚, 马英杰, 雷家峰, 杨锐. 峰值应力对Ti6242压气机盘锻件室温保载效应的影响[J]. 金属学报, 2025, 61(8): 1141-1152.
[9] 游云翔, 谭力, 高静静, 周涛, 周志明. 利用热轧制-剪切-弯曲工艺及退火调控Mg-Al-Zn-Mn-Ca 镁合金的织构[J]. 金属学报, 2025, 61(6): 866-874.
[10] 周小卫, 郭云, 荆雪艳, 王宇鑫. 仿生苍耳球冠织构的Ni-Co-Zn超疏水合金涂层及其抗覆冰性能[J]. 金属学报, 2025, 61(5): 783-796.
[11] 赵焯雅, 孟令健, 林鹏, 曹晓卿. TC4钛合金跨相区连续热压缩 α 相组织演变规律及织构形成机理[J]. 金属学报, 2025, 61(5): 717-730.
[12] 齐敏, 王倩, 马英杰, 曹贺萌, 黄森森, 雷家峰, 杨锐. Ti6246钛合金 β → α 相变中晶界 α 相生长行为及其对微织构的影响[J]. 金属学报, 2025, 61(2): 265-277.
[13] 王子彧, 陈志勇, 王新, 王清江. Ti2AlNb薄板的织构及其对拉伸性能各向异性的影响[J]. 金属学报, 2025, 61(11): 1625-1637.
[14] 颜孟奇, 吴泽浩, 佟健博, 黄利军, 黄驿胜. TC18钛合金大尺寸 β 晶粒制备及典型织构对力学性能的影响[J]. 金属学报, 2025, 61(10): 1555-1566.
[15] 朱桂杰, 王思清, 查敏, 李眉娟, 孙凯, 陈东风. 稀土元素Ce对挤压态Mg-0.3Al-0.2Ca-0.5Mn合金板材体织构及力学各向异性的影响[J]. 金属学报, 2024, 60(8): 1079-1090.