预拉伸变形对欠时效<strong>7N01</strong>铝合金板材疲劳断裂的影响

doi:10.11900/0412.1961.2021.00017

金属学报

2022, Vol. 58

Issue (6): 760-770 DOI: 10.11900/0412.1961.2021.00017

研究论文

本期目录 | 过刊浏览

预拉伸变形对欠时效7N01铝合金板材疲劳断裂的影响

田妮¹^,²(

), 石旭¹, 刘威¹, 刘春城³, 赵刚¹^,², 左良²^,⁴

^1.东北大学材料科学与工程学院沈阳 110819
^2.东北大学材料各向异性与织构教育部重点实验室沈阳 110819
^3.东北大学工程训练中心沈阳 110819
^4.中国科学院金属研究所沈阳 110016

Effect of Pre-Tension on the Fatigue Fracture of Under-Aged 7N01 Aluminum Alloy Plate

TIAN Ni¹^,²(

), SHI Xu¹, LIU Wei¹, LIU Chuncheng³, ZHAO Gang¹^,², ZUO Liang²^,⁴

^1.School of Materials Science and Engineering, Northeastern University, Shenyang 110819, China
^2.Key Laboratory for Anisotropy and Texture of Materials (Ministry of Education), Northeastern University, Shenyang 110819, China
^3.Engineering Training Center, Northeastern University, Shenyang 110819, China
^4.Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016, China

引用本文:

田妮, 石旭, 刘威, 刘春城, 赵刚, 左良. 预拉伸变形对欠时效7N01铝合金板材疲劳断裂的影响[J]. 金属学报, 2022, 58(6): 760-770.
Ni TIAN, Xu SHI, Wei LIU, Chuncheng LIU, Gang ZHAO, Liang ZUO. Effect of Pre-Tension on the Fatigue Fracture of Under-Aged 7N01 Aluminum Alloy Plate[J]. Acta Metall Sin, 2022, 58(6): 760-770.

全文: PDF(3240 KB) HTML

摘要:

针对工业化生产的7N01铝合金板材,采用拉伸实验、疲劳实验和微观组织结构表征等手段研究了预拉伸变形对欠时效态7N01铝合金板材疲劳性能和疲劳断裂特征的影响。结果表明,预拉伸变形量增大至20%,欠时效态7N01铝合金板材中合金相粒子的形状、尺寸、数量、分布以及薄带状晶粒的尺寸和形状基本保持不变。然而,板材表现出明显的加工硬化效应,其屈服强度、抗拉强度和显微硬度分别由181 MPa、233 MPa和95 HV增大至254 MPa、271 MPa和117 HV,延伸率从23.2%降低至5.2%。在应力175 MPa、应力比R = 0的疲劳循环加载条件下,随预拉伸变形量的增加,欠时效态7N01铝合金板材的疲劳寿命呈现出先缩短再延长又缩短的趋势。未预拉伸变形试样的疲劳寿命为6.06 × 10⁵ cyc,5%预拉伸变形可将铝板的疲劳寿命延长75%,达到了1.06 × 10⁶ cyc,而3%和20%的预拉伸变形将铝板的疲劳寿命分别缩短至4.21 × 10⁵和2.89 × 10⁵ cyc。5%~16%预拉伸变形使欠时效态7N01铝合金板材基体中形成均匀分布的高密度位错或位错胞的显微组织,可将合金板材的疲劳寿命延长23%以上。

关键词 ： 7N01铝合金板材, 预拉伸变形, 欠时效, 位错, 疲劳

Abstract：

7N01 aluminum alloy is the main load-bearing structure material for bullet train bodies due to its high specific strength, high specific stiffness, good magnetic-shielding ability, strong corrosion resistance, and good formability and weldability. The fatigue performance of materials and components used in bullet trains determines their security. It is unavoidable that there is pre-deformation during the assembly process of aluminum alloy components, which will influence the active service and fatigue performance of the aluminum alloy. It is important not only to clarify the relationship between pre-deformation and fatigue performance but also to reveal the mechanism of pre-deformation on the fatigue fracture of 7N01 aluminum alloy, to ensure the security of the bullet train. In this study, the effect of pre-tensile deformation on the fatigue property, fatigue fracture initiation, and fatigue crack propagation characteristics of a commercial 7N01 aluminum alloy plate at under-aged conditions was studied using tensile and fatigue tests combined with microstructure analysis. As the pre-tensile deformation increased to 20%, the results showed that the shape, size, number, distribution of second phase particles, as well as the size and morphology of thin strips grain of under-aged 7N01 aluminum alloy plate were almost the same. However, the under-aged 7N01 aluminum alloy plate has a significant strain-hardening effect after pre-tensile at room temperature, with the yield strength, tensile strength, and hardness increased from 181 MPa, 233 MPa, and 95 HV (without pre-tensile deformation) to 254 MPa, 271 MPa, and 117 HV (after 20% pre-tensile deformation), while the elongation decreased from 23.2% to 5.2%. Under the 175 MPa pulsating tensile load condition (stress ratio R = 0), the overall fatigue life of the under-aged 7N01 aluminum alloy plate first reduced, then prolonged, and then decreased as pre-tensile deformation increased. Without pre-tensile deformation, the fatigue life of under-aged 7N01 aluminum alloy plate is about 6.06 × 10⁵ cyc, and when prolonged by about 75%, it reaches about 1.06 × 10⁶ cyc after 5% pre-tensile deformation. However, the fatigue life of the under-aged 7N01 aluminum alloy plate is decreased to 4.21 × 10⁵ and 2.89 × 10⁵ cyc after 3% and 20% pre-tensile deformation, respectively. The evenly distributed high-density dislocations or dislocation cells resulted in 5%-16% pre-tensile deformation in the under-aged 7N01 aluminum alloy plate, which can prolong the fatigue life of the alloy plate by over 23%.

Key words： 7N01 aluminum alloy plate pre-tensile deformation under-aged dislocation fatigue

收稿日期: 2021-01-14

ZTFLH:

TG146.2

基金资助:国家自然科学基金项目(51871043);中央高校基本科研业务费项目(180212010);辽宁省自然科学基金项目(2019-MS-113)

作者简介: 田妮,女,1975年生,副教授,博士

	服务

	把本文推荐给朋友
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	田妮
	石旭
	刘威
	刘春城
	赵刚
	左良
44.8K

链接本文:

https://www.ams.org.cn/CN/10.11900/0412.1961.2021.00017 或 https://www.ams.org.cn/CN/Y2022/V58/I6/760

图1 拉伸及疲劳试样尺寸

图2 欠时效态7N01铝合金板材及其经不同程度预拉伸变形后显微组织的OM像(纵截面,未腐蚀)

图3 欠时效态7N01铝合金板材及其经不同程度预拉伸变形后的晶粒OM像(纵截面)

图4 欠时效态7N01铝合金板材经不同程度预拉伸变形后组织的TEM像

图5 欠时效态7N01铝合金板材经不同程度预拉伸变形量后的力学性能

图6 欠时效态7N01铝合金板材经不同程度预拉伸变形后的疲劳寿命

图7 欠时效态7N01铝合金板材经不同程度预拉伸变形后的疲劳断口表面裂纹源处SEM像

图8 欠时效态7N01铝合金板材经不同程度预拉伸变形后的疲劳断口表面裂纹扩展区形貌的SEM像

表1 不同程度预拉伸变形后,欠时效态7N01铝合金板材中疲劳裂纹萌生阻力贡献值(λi)、疲劳裂纹扩展阻力贡献值(λp)及疲劳寿命贡献值(λ)的分析结果

图9 欠时效态7N01铝合金板材经不同程度预拉伸变形后的疲劳裂纹扩展示意图

1	Deschamps A, Texier G, Ringeval S, et al. Influence of cooling rate on the precipitation microstructure in a medium strength Al-Zn-Mg alloy [J]. Mater. Sci. Eng., 2009, A501: 133
2	Heinz A, Haszler A, Keidel C, et al. Recent development in aluminium alloys for aerospace applications [J]. Mater. Sci. Eng., 2000, A280: 102
3	Liu W H, Liu W B, Bao A L. Microstructure and properties of ceramic coatings on 7N01 aluminum alloy by micro-arc oxidation [J]. Procedia Eng., 2012, 27: 828 doi: 10.1016/j.proeng.2011.12.527
4	Branco R, Costa J D, Borrego L P, et al. Effect of tensile pre-strain on low-cycle fatigue behaviour of 7050-T6 aluminium alloy [J]. Eng. Fail. Anal., 2020, 114: 104592 doi: 10.1016/j.engfailanal.2020.104592
5	Branco R, Borrego L P, Costa J D, et al. Effect of pre-strain on cyclic plastic behaviour of 7050-T6 aluminium alloy [J]. Procedia Struct. Integr., 2019, 17: 177 doi: 10.1016/j.prostr.2019.08.024
6	Niendorf T, Lotze C, Canadinc D, et al. The role of monotonic pre-deformation on the fatigue performance of a high-manganese austenitic TWIP steel [J]. Mater. Sci. Eng., 2009, A499: 518
7	Gustavsson A, Melander A. Fatigue of a highly prestrained dual-phase sheet steel [J]. Fatigue Fract. Eng. Mater. Struct., 1995, 18(2): 201 doi: 10.1111/j.1460-2695.1995.tb00155.x
8	Uemura T. A fatigue life estimation of specimens excessively prestrained in tension [J]. Fatigue Fract. Eng. Mater. Struct., 1998, 21: 151 doi: 10.1046/j.1460-2695.1998.00223.x
9	Al-Rubaie K S, Del Grande M A, Travessa D N, et al. Effect of pre-strain on the fatigue life of 7050-T7451 aluminium alloy [J]. Mater. Sci. Eng., 2007, A464: 141
10	Schijve J. The effect of pre-strain on fatigue crack growth and crack closure [J]. Eng. Fract. Mech., 1976, 8: 575 doi: 10.1016/0013-7944(76)90031-X
11	Froustey C, Lataillade J L. Influence of large pre-straining of aluminium alloys on their residual fatigue resistance [J]. Int. J. Fatigue, 2008, 30(5): 908 doi: 10.1016/j.ijfatigue.2007.06.011
12	Arora P R, Raghavan M R. Effect of tensile prestrain on fatigue strength of aluminum alloy in high cycle fatigue [J]. J. Eng. Mater. Technol., 1973, 95: 76 doi: 10.1115/1.3443135
13	Hodgson P, Parker B A. The composition of insoluble intermetallic phases in aluminium alloy 6010 [J]. J. Mater. Sci., 1981, 16: 1343 doi: 10.1007/BF01033850
14	Adrien J, Maire E, Estevez R, et al. Influence of the thermomechanical treatment on the microplastic behaviour of a wrought Al-Zn-Mg-Cu alloy [J]. Acta Mater., 2004, 52: 1653 doi: 10.1016/j.actamat.2003.12.009
15	Benoit S G, Chalivendra V B, Rice M A, et al. Characterization of the microstructure, fracture, and mechanical properties of aluminum alloys 7085-O and 7175-T7452 hollow cylinder extrusions [J]. Metall. Mater. Trans., 2016, 47A: 4476
16	Hou L G, Xiao W L, Su H, et al. Room-temperature low-cycle fatigue and fracture behaviour of asymmetrically rolled high-strength 7050 aluminium alloy plates [J]. Int. J. Fatigue, 2021, 142: 105919 doi: 10.1016/j.ijfatigue.2020.105919
17	Wen K, Fan Y Q, Wang G J, et al. Aging behavior and fatigue crack propagation of high Zn-containing Al-Zn-Mg-Cu alloys with zinc variation [J]. Prog. Nat. Sci., 2017, 27: 217 doi: 10.1016/j.pnsc.2017.02.002
18	Tian N, Zhao G, Zuo L, et al. Study on the strain hardening behavior of Al-Mg-Si-Cu alloy sheet for automotive body [J]. Acta. Metall. Sin., 2010, 46: 613 doi: 10.3724/SP.J.1037.2009.00799
18	田妮, 赵刚, 左良等. 汽车车身用Al-Mg-Si-Cu合金薄板应变强化行为的研究 [J]. 金属学报, 2010, 46: 613
19	Wang Z X, Li H, Wei X Y, et al. Effects of prior strain on static tensile properties and fatigue lives of 2E12 aluminum alloy [J]. Rare Met. Mater. Eng., 2010, 39(): 138
19	王芝秀, 李海, 魏修宇等. 预变形对2E12铝合金拉伸性能和疲劳寿命的影响 [J]. 稀有金属材料与工程, 2010, 39(): 138
20	Schijve J, translated by Wu X R, et al. Fatigue of Structures and Materials [M]. 2nd Ed., Beijing: Aviation Industry Press, 2014: 30
20	Schijve J著, 吴学仁等译 . 结构与材料的疲劳 [M]. 第2版, 北京: 航空工业出版社, 2014: 30
21	Wang X S, Liang F, Zeng Y P, et al. SEM in situ observations to the effects of inclusion on initiation and propagation of the low cyclic fatigue crack in super strength steel [J]. Acta. Metall. Sin, 2005, 41: 1272
21	王习术, 梁锋, 曾燕屏, 等. 夹杂物对超高强度钢低周疲劳裂纹萌生及扩展影响的原位观测 [J]. 金属学报, 2005, 41(12): 1272
22	Bai S, Liu Z Y, Gu Y X, et al. Microstructures and fatigue fracture behavior of an Al-Cu-Mg-Ag alloy with a low Cu/Mg ratio [J]. Mater. Sci. Eng., 2011, A530: 473
23	Xu L P, Wang Q Y, Zhou M. Micro-crack initiation and propagation in a high strength aluminum alloy during very high cycle fatigue [J]. Mater. Sci. Eng., 2018, A715: 404
24	Yao W X, Guo S J. Gigacycle fatigue life distribution of aluminum alloy LC4CS [J]. Acta. Metall. Sin., 2007, 43: 399
24	姚卫星, 郭盛杰. LC4CS铝合金的超高周疲劳寿命分布 [J]. 金属学报, 2007, 43: 399
25	Zang X C, Xie L Y, Hu J X, et al. Effect of service on fracture mechanical properties of 7N01 aluminum alloy [J]. J. Northeast. Univ. (Nat. Sci.), 2017, 38: 1442
25	张啸尘, 谢里阳, 胡杰鑫, 等. 服役经历对7N01铝合金断裂力学性能的影响 [J]. 东北大学学报(自然科学版), 2017, 38: 1442
26	Jian H G, Jiang F, Wei L L, et al. Crystallographic mechanism for crack propagation in the T7451 Al-Zn-Mg-Cu alloy [J]. Mater. Sci. Eng., 2010, A527: 5879
27	Nandana M S, Udaya Bhat K, Manjunatha C M. Influence of retrogression and re-ageing heat treatment on the fatigue crack growth behavior of 7010 aluminum alloy [J]. Procedia Struct. Integr., 2019, 14: 314 doi: 10.1016/j.prostr.2019.05.039

[1]	赵鹏, 谢光, 段慧超, 张健, 杜奎. 两种高代次镍基单晶高温合金热机械疲劳中的再结晶行为[J]. 金属学报, 2023, 59(9): 1221-1229.
[2]	王磊, 刘梦雅, 刘杨, 宋秀, 孟凡强. 镍基高温合金表面冲击强化机制及应用研究进展[J]. 金属学报, 2023, 59(9): 1173-1189.
[3]	李嘉荣, 董建民, 韩梅, 刘世忠. 吹砂对DD6单晶高温合金表面完整性和高周疲劳强度的影响[J]. 金属学报, 2023, 59(9): 1201-1208.
[4]	江河, 佴启亮, 徐超, 赵晓, 姚志浩, 董建新. 镍基高温合金疲劳裂纹急速扩展敏感温度及成因[J]. 金属学报, 2023, 59(9): 1190-1200.
[5]	张禄, 余志伟, 张磊成, 江荣, 宋迎东. GH4169高温合金热机械疲劳循环损伤机理及数值模拟[J]. 金属学报, 2023, 59(7): 871-883.
[6]	张滨, 田达, 宋竹满, 张广平. 深潜器耐压壳用钛合金保载疲劳服役可靠性研究进展[J]. 金属学报, 2023, 59(6): 713-726.
[7]	张哲峰, 李克强, 蔡拓, 李鹏, 张振军, 刘睿, 杨金波, 张鹏. 层错能对面心立方金属形变机制与力学性能的影响[J]. 金属学报, 2023, 59(4): 467-477.
[8]	韩卫忠, 卢岩, 张雨衡. 体心立方金属韧脆转变机制研究进展[J]. 金属学报, 2023, 59(3): 335-348.
[9]	戚钊, 王斌, 张鹏, 刘睿, 张振军, 张哲峰. 应力比对含缺陷选区激光熔化TC4合金稳态疲劳裂纹扩展速率的影响[J]. 金属学报, 2023, 59(10): 1411-1418.
[10]	韩冬, 张炎杰, 李小武. 短程有序对高层错能Cu-Mn合金拉-拉疲劳变形行为及损伤机制的影响[J]. 金属学报, 2022, 58(9): 1208-1220.
[11]	宋文硕, 宋竹满, 罗雪梅, 张广平, 张滨. 粗糙表面高强铝合金导线疲劳寿命预测[J]. 金属学报, 2022, 58(8): 1035-1043.
[12]	周红伟, 高建兵, 沈加明, 赵伟, 白凤梅, 何宜柱. 高温低周疲劳下C-HRA-5奥氏体耐热钢中孪晶界演变[J]. 金属学报, 2022, 58(8): 1013-1023.
[13]	郑士建, 闫哲, 孔祥飞, 张瑞丰. 纳米金属层状材料强塑性的界面调控[J]. 金属学报, 2022, 58(6): 709-725.
[14]	高川, 邓运来, 王冯权, 郭晓斌. 蠕变时效对欠时效7075铝合金力学性能的影响[J]. 金属学报, 2022, 58(6): 746-759.
[15]	杨秦政, 杨晓光, 黄渭清, 石多奇. 粉末高温合金FGH4096的疲劳小裂纹扩展行为[J]. 金属学报, 2022, 58(5): 683-694.

Viewed

Full text

Abstract

Cited

Shared

Discussed