Please wait a minute...
金属学报    DOI: 10.11900/0412.1961.2026.00202
  本期目录 | 过刊浏览 |
Nb-V微合金化钢的抗高压氢脆机制

刘 璐1   齐亚猛2,3   张忠铧2,3   施 浩2,3   李 喜1

1 上海交通大学 材料科学与工程学院  上海 200240

2 宝山钢铁股份有限公司 中央研究院  上海 201900

3 宝山钢铁股份有限公司 油气钻采输送装备全国重点实验室  上海 201900

High-Pressure Hydrogen Embrittlement Resistance Mechanism of Nb and V Microalloyed Steel

LIU Lu 1, QI Yameng 2,3, ZHANG Zhonghua 2,3, SHI Hao 2,3, LI Xi 1

1 School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240, China

2 Baosteel Research Institute, Baoshan Iron and Steel Co. Ltd., Shanghai 201900, China

3 State Key Laboratory of Oil and Gas Equipment, Baoshan Iron and Steel Co. Ltd, Shanghai 201900, China

引用本文:

刘璐, 齐亚猛, 张忠铧, 施浩, 李喜. Nb-V微合金化钢的抗高压氢脆机制[J]. 金属学报, DOI: 10.11900/0412.1961.2026.00202.

全文: PDF(6775 KB)  
摘要: 
为改善高压储氢用低合金钢的抗氢脆性能,探索微合金化与回火工艺的组织调控途径,采用EBSD、TEM、TDS和SSRT等手段对比了强度相近的基准钢、Nb微合金化钢及Nb-V复合微合金化钢的组织、纳米析出、氢俘获及100 MPa氢气中的断裂行为。结果表明,Nb添加后原始奥氏体晶粒减小,板条边界M23C6转为断续长条状。复合添加后M23C6进一步离散化,并形成(Nb, V)C,MC的体积分数由0.85%增至2.75%。复合微合金化钢的高温脱附峰向高温侧偏移并展宽。100 MPa H2中,复合微合金化钢的延伸率损失率由基准钢的48.3%降至13.3%,韧窝和解理面积分数分别为55.6%和15.7%。上述结果表明,通过微合金化与回火工艺调控MC析出及M23C6分布,可改善低合金钢在高压氢气中的抗氢脆性能。
关键词 : 低合金钢,  Nb-V微合金化,  (Nb,V)C复合碳化物,  氢脆    
Abstract:

 Low-alloy steels are promising materials for high-pressure hydrogen storage because of their favorable combination of strength, toughness, and cost. However, hydrogen embrittlement can reduce ductility and promote premature fracture. Microalloying offers a route to modify carbide precipitation and hydrogen trapping, but the microstructural mechanisms underlying the benefits of combined Nb and V additions require further clarification. This study investigated microstructural control through microalloying and tempering to improve hydrogen embrittlement resistance. A base steel, an Nb-microalloyed steel, and an Nb-V co-microalloyed steel were subjected to identical austenitization and quenching, followed by tempering at different temperatures to obtain comparable tensile strengths near 850 MPa. Electron backscatter diffraction, transmission electron microscopy, thermal desorption spectroscopy (TDS), and slow strain rate tensile testing were used to characterize microstructures, precipitates, hydrogen desorption, and fracture behavior. TDS measurements used identical electrochemical charging conditions and heating rates, whereas tensile tests were conducted in 100 MPa gaseous hydrogen at room temperature. Both microalloyed steels exhibited smaller prior austenite grains than the base steel, accompanied by modest refinement of the quenched and tempered microstructure. In the Nb-microalloyed steel, M23C6 carbides were distributed discontinuously as elongated particles along lath boundaries. In the Nb-V co-microalloyed steel, M23C6 became more discrete, and nanoscale (Nb, V)C precipitates formed. Compared with the Nb-microalloyed steel, the estimated volume fraction of MC-type precipitates increased from 0.85% to 2.75%, while the average size increased slightly from 6.89 nm to 7.56 nm. The two microalloyed steels exhibited similar low-temperature desorption peaks, whereas the high-temperature peak shifted to higher temperatures and broadened in the Nb-V co-microalloyed steel. Combined with precipitate characterization, this behavior suggests that some hydrogen traps may have higher binding energies. In 100 MPa hydrogen, the relative loss in elongation decreased from 48.3% for the base steel to 28.1% for the Nb-microalloyed steel and 13.3% for the Nb-V co-microalloyed steel. The latter exhibited dimple and cleavage area fractions of 55.6% and 15.7%, respectively. Increased MC precipitation and a more discrete M23C6 distribution may improve hydrogen embrittlement resistance by enhancing hydrogen trapping and inhibiting microcrack propagation, with grain refinement potentially providing a secondary contribution.

收稿日期: 2026-07-24     
[1] 杜德灏, 管明, 曹祚恒, 王铭, 何斌斌, 黄明欣. 热成形汽车钢的弯曲韧性与氢脆行为研究进展[J]. 金属学报, 2026, 62(5): 959-974.
[2] 宝尔根, 王建韬, 徐文静, 马会, 陈星秋. 合金元素对 α-Fe中H原子溶解及扩散影响的第一性原理研究[J]. 金属学报, 2026, 62(3): 489-496.
[3] 杨波, 陈小亮, 史晓斌, 任伟, 高恒, 宋广生. 稀土Y掺杂V-Cr合金增塑机理及透氢性能[J]. 金属学报, 2025, 61(6): 887-899.
[4] 闫茂鑫, 李杰, 王哲超, 姚旭, 胡秉晨, 葛峰, 崔中雨, 王昕, 崔洪芝. 南极大气环境下Q460和Q690 低合金钢的腐蚀行为[J]. 金属学报, 2025, 61(2): 297-308.
[5] 苏帅, 韩鹏, 杨善武, 王华, 金耀辉, 尚成嘉. Ni含量对高强度低合金钢淬透性影响的晶体学认识[J]. 金属学报, 2024, 60(6): 789-801.
[6] 肖娜, 惠卫军, 张永健, 赵晓丽. 真空渗碳处理齿轮钢的氢脆敏感性[J]. 金属学报, 2021, 57(8): 977-988.
[7] 兰亮云, 孔祥伟, 邱春林, 杜林秀. 基于多尺度力学实验的氢脆现象的最新研究进展[J]. 金属学报, 2021, 57(7): 845-859.
[8] 刘振宝,梁剑雄,苏杰,王晓辉,孙永庆,王长军,杨志勇. 高强度不锈钢的研究及发展现状[J]. 金属学报, 2020, 56(4): 549-557.
[9] 李金许,王伟,周耀,刘神光,付豪,王正,阚博. 汽车用先进高强钢的氢脆研究进展[J]. 金属学报, 2020, 56(4): 444-458.
[10] 马宏驰, 杜翠薇, 刘智勇, 李永, 李晓刚. E690高强低合金钢焊接热影响区典型组织在含SO2海洋环境中的应力腐蚀行为对比研究[J]. 金属学报, 2019, 55(4): 469-479.
[11] 赵晓丽, 张永健, 邵成伟, 惠卫军, 董瀚. 两相区退火处理冷轧0.1C-5Mn中锰钢的氢脆敏感性[J]. 金属学报, 2018, 54(7): 1031-1041.
[12] 邹佳男, 庞晓露, 高克玮. 低合金钢X70和3Cr在超临界CO2环境中的缝隙腐蚀[J]. 金属学报, 2018, 54(4): 537-546.
[13] 孙军, 李苏植, 丁向东, 李巨. 氢化空位的基本性质及其对金属力学行为的影响[J]. 金属学报, 2018, 54(11): 1683-1692.
[14] 余军, 张德平, 潘若生, 董泽华. 井下含硫环空液中P110油管钢应力腐蚀开裂的电化学噪声特征[J]. 金属学报, 2018, 54(10): 1399-1407.
[15] 刘峰, 王慷. 低合金钢TMCP中相变热力学/动力学相关性探讨*[J]. 金属学报, 2016, 52(10): 1326-1332.