Please wait a minute...
Acta Metall Sin  2026, Vol. 62 Issue (10): 1749-1761    DOI: 10.11900/0412.1961.2024.00348
Research paper Current Issue | Archive | Adv Search |
Effects of Preaging Treatment on the Hot Deformation Behavior and Microstructural Evolution of Al-Zn-Mg-Cu Alloys
WANG Zhenyu1,2, SHI Quanqiang1(), FAN Ran3, CUI Li4, WANG Wei1()
1 Shi -changxu Innovation Center for Advanced Materials, Institute of Metals Research, Chinese Academy of Sciences, Shenyang 110016, China
2 School of Materials Science and Engineering, University of Science and Technology of China, Shenyang 110016, China
3 Office of the First Military Representative of the Air Force in the Shenyang Area, Shenyang 110843, China
4 Shenyang Aircraft Corporation, Shenyang 110039, China
Cite this article: 

WANG Zhenyu, SHI Quanqiang, FAN Ran, CUI Li, WANG Wei. Effects of Preaging Treatment on the Hot Deformation Behavior and Microstructural Evolution of Al-Zn-Mg-Cu Alloys. Acta Metall Sin, 2026, 62(10): 1749-1761.

Download:  HTML  PDF(2677KB) 
Export:  BibTeX | EndNote (RIS)      
Abstract  

To investigate the service behavior of aerospace-grade Al-Zn-Mg-Cu alloys under thermomechanical coupling conditions, this study examines the effects of preaging treatment on their hot deformation behavior through thermal simulation experiments. The flow stress curves obtained from these simulations reveal the following: at a low strain rate of 0.01 s-1, the flow stress in the solid-solution state exceeds that in the aged state during hot deformation at 293 and 473 K. However, between 573 and 743 K, the aged state exhibits higher flow stress than the solid-solution state, with the difference diminishing as the temperature increases. At a high strain rate of 0.5 s-1, the flow stress difference between the solid-solution and aged states decreases with increasing temperature, while that increases abnormally at 743 K. To understand these phenomena, microstructural evolution in the aged and solid-solution Al-Zn-Mg-Cu alloys was studied using SEM, EBSD, and TEM. The results show that at low strain rates and 473-573 K, a high density of precipitates leads to entanglement of the dislocations, leading to low deformation storage energy and high thermal deformation activation energy in the aged alloys. This results in poor matrix recovery and enhanced deformation resistance. At 673 K, discontinuous coarsening of the precipitates and an increase in the deformation storage energy increase the dynamic recovery volume fraction of the aged alloy. At 743 K, the presence of small spherical particles that pin dislocations increases the deformation storage energy and promotes dynamic recrystallization (DRX) in the matrix, resulting in flow stress in the aged state comparable to that in the solid-solution state. At high strain rates, the occurrence of geometric DRX in the aged alloy further increases the DRX volume fraction, thereby reducing the flow stress.

Key words:  Al-Zn-Mg-Cu alloy      preaging      hot deformation behavior      precipitate      dynamic softening     
Received:  18 October 2024     
ZTFLH:  TG146.2  
Fund: National Key Research and Development Program of China(2022YFB3705200);National Na-tural Science Foundation of China(52271122)
Corresponding Authors:  WANG Wei, professor, Tel: (024)83978745, E-mail: wangw@imr.ac.cn;
SHI Quanqiang, associate professor, Tel: (024)83978745, E-mail: qqshi12b@imr.ac.cn

URL: 

https://www.ams.org.cn/EN/10.11900/0412.1961.2024.00348     OR     https://www.ams.org.cn/EN/Y2026/V62/I10/1749

Fig.1  Schematic of the thermal simulation experiments of Al-Zn-Mg-Cu alloys (Inset shows the dimensions of the sample before and after thermal compression. unit: mm)
Fig.2  Original microstructure characterizations of solid-solution state (a1-a3, c1-c3) and aging state (b1-b3, d1-d3) Al-Zn-Mg-Cu alloys (HAGB—high-angle grain boundary, > 15o; LAGB—low-angle grain boundary, 2o-10o; MAGB—medium-angle grain boundary, 10o-15o. The significance of the color representation of inverse pole figure (IPF) and kernel average misorientation (KAM) plots in this paper is consistent with Figs.2a1 and a3, respectively)
(a1, b1) IPF maps (a2, b2) grain boundary orientation difference maps (a3, b3) KAM maps (The average KAM values are provided in the upper-right corner) (c1, d1) TEM images (c2, d2) EDS mappings (c3, d3) HRTEM images and corresponding fast Fourier transform (FFT) images of the box areas
Fig.3  Stress-strain curves of Al-Zn-Mg-Cu alloys under solid-solution and aging states (a-c) and differences in rheological stress of alloys between solid-solution state and aging state (d)
(a) ε˙ = 0.01 s-1, room temperature compression
(b) ε˙ = 0.01 s-1, 473-743 K compression
(c) ε˙ = 0.50 s-1, 473-743 K compression (Inset shows the enlargement of the dotted box)
Fig.4  TEM images of solid-solution state (a, b) and aging state (c, d) Al-Zn-Mg-Cu alloys at 473 K and ε˙ = 0.01 s-1
(a, c) morphologies of precipitates and dislocation entanglement (GP—Guinier-Preston) (b, d) morphologies of precipitation free zone
Fig.5  EBSD analyses of solid-solution state (a1-a4) and aging state (b1-b4) Al-Zn-Mg-Cu alloys at 573 K and ε˙ = 0.01 s-1 (a1, b1) IPF maps (Dynamic recrystallization (DRX) grains are shown in the boxes. CDRX—continuous dynamic recrystallization, DDRX—discontinuous dynamic recrystallization) (a2, b2) grain boundary maps (a3, b3) KAM maps (a4, b4) recrystallization maps (Blue for recrystallized grains, yellow for substructures, and red for deformed grains)
Fig.6  Morphologies of solid-solution state (a-c) and aging state (d-f) Al-Zn-Mg-Cu alloys at 573 K and ε˙ = 0.01 s-1
(a, d) SEM images of the precipitates (b, e) TEM images of the precipitates and dislocations (c, f) TEM images of the DRX grains (c) and the coarse precipitates (f)
Fig.7  EBSD analyses of solid-solution state (a1-a4) and aging state (b1-b4) Al-Zn-Mg-Cu alloys at 673 K and ε˙ = 0.01 s-1
(a1, b1) IPF maps (DRX grains are shown in the boxes) (a2, b2) grain boundary maps (a3, b3) KAM maps (a4, b4) recrystallization maps (Blue for recrystallized grains, yellow for substructures, and red for deformed grains)
Fig.8  TEM images of solid-solution state (a-c) and aging state (d-f) Al-Zn-Mg-Cu alloys at 673 K and ε˙ = 0.01 s-1
(a, d) morphologies of DRX grains (b, c) morphologies between precipitates (b) and double-wall microbands (c) (e) interaction between fine precipitates and dislocations (f) discontinuous coarsening of precipitates
Temperature / KState

Volume fraction of

deformed grains / %

Volume fraction of

substructures / %

Volume fraction of

recrystallized grains / %

573Solid-solution75.721.23.1
Aging98.00.91.1
673Solid-solution52.323.624.1
Aging62.025.812.2
Table 1  Statistics on the proportion of deformed grains, substructures, and recrystallized grains in solid-solution and aging state Al-Zn-Mg-Cu alloys at strain rate of 0.01 s-1 and temperatures of 573 and 673 K
Fig.9  EBSD analyses of solid-solution state (a1-a4, b1-b4) and aging state (c1-c4, d1-d4) Al-Zn-Mg-Cu alloys at 743 K with strain rates of 0.01 s-1 (a1-a4, c1-c4) and 0.50 s-1 (b1-b4, d1-d4) (GDRX—geometric dynamic recrystallization)
(a1-d1) IPF maps (DRX grains are shown in the boxes) (a2-d2) grain boundary maps (a3-d3) KAM maps (a4-d4) recrystallization maps (Blue for recrystallized grains, yellow for substructures, and red for deformed grains)
StateStrain rates / s-1

Volume fraction of

deformed grains / %

Volume fraction of

substructures / %

Volume fraction of

recrystallized grains / %

Solid-solution0.0135.734.130.2
0.583.72.114.2
Aging0.0133.330.536.2
0.572.87.619.6
Table 2  Statistics on the proportion of deformed grains, substructures, and recrystallized grains in solid-solution and aging state Al-Zn-Mg-Cu alloys at 743 K under different strain rates
Fig.10  TEM images of solid-solution state (a-d) and aging state (e-h) Al-Zn-Mg-Cu alloys at 743 K with different strain rates
(a, b, e, f) 0.01 s-1 (c, d, g, h) 0.50 s-1
Fig.11  Schematics of microstructure evolution of Al-Zn-Mg-Cu alloy during heat deformation process
(a) solid-solution state (b) aging state
[1] Dursun T, Soutis C. Recent developments in advanced aircraft aluminium alloys[J]. Mater. Des. (1980-2015), 2014, 56: 862
doi: 10.1016/j.matdes.2013.12.002
[2] Lin Y C, Chen X M. A critical review of experimental results and constitutive descriptions for metals and alloys in hot working[J]. Mater. Des., 2011, 32: 1733
doi: 10.1016/j.matdes.2010.11.048
[3] Deng Y L, Zhang Y Y, Wan L, et al. Effects of thermomechanical processing on production of Al-Zn-Mg-Cu alloy plate[J]. Mater. Sci. Eng., 2012, A554: 33
[4] Dwivedi P, Siddiquee A N, Maheshwari S. Issues and requirements for aluminum alloys used in aircraft components: State of the art[J]. Russ. J. Non-Ferr. Met., 2021, 62: 212
[5] Gholizadeh R, Yoshida S, Bai Y, et al. Global understanding of deformation behavior in CoCrFeMnNi high entropy alloy under high-strain torsion deformation at a wide range of elevated temperatures[J]. Acta Mater., 2023, 243: 118514
doi: 10.1016/j.actamat.2022.118514
[6] Su M N, Young B. Material properties of normal and high strength aluminium alloys at elevated temperatures[J]. Thin-Wall. Struct., 2019, 137: 463
doi: 10.1016/j.tws.2019.01.012
[7] Bo G W, Jiang F L, Dong Z Y, et al. Revealing the influence of pre-precipitation microstructure on hot workability in an Al-Cu-Mg-Zr alloy[J]. Mater. Sci. Eng., 2019, A755: 147
[8] Long M J, Jiang F, Wu F F, et al. Hot deformation behavior and microstructure evolution of a novel high-Zn containing Al-Zn-Mg-Cu-Zr alloy[J]. J. Mater. Eng. Perform., 2025, 34: 4502
doi: 10.1007/s11665-024-09506-3
[9] Mao Y Z, Li J G, Feng L. Effect of coarse β(Al3Mg2) phase on microstructure evolution in 573 K annealed Al-10Mg alloy by uniaxial compression[J]. Acta Metall. Sin., 2018, 54: 1451
毛轶哲, 李建国, 封 蕾. 573K高温时效处理的Al-10Mg合金中粗大β(Al3Mg2)相对热压缩组织演化的影响及机理[J]. 金属学报, 2018, 54: 1451
doi: 10.11900/0412.1961.2018.00072
[10] Li T R, Xu Y Q, Wu W P, et al. Effects of V and B on the microstructure evolution and deformation mechanisms of Ti-44Al-5Nb-1Mo alloys[J]. Acta Metall. Sin., 2024, 60: 650
李天瑞, 许瑜倩, 吴文平 等. V和B元素对Ti-44Al-5Nb-1Mo合金显微组织及热变形机制的影响[J]. 金属学报, 2024, 60: 650
doi: 10.11900/0412.1961.2022.00557
[11] Chen S H, Wang Q Y, Jiang H C, et al. Effect of δ-ferrite on hot deformation and recrystallization of 316KD austenitic stainless steel for sodium-cooled fast reactor application[J]. Acta Metall. Sin., 2024, 60: 367
陈胜虎, 王琪玉, 姜海昌 等. δ-铁素体对钠冷快堆用316KD奥氏体不锈钢热变形行为和动态再结晶的影响[J]. 金属学报, 2024, 60: 367
doi: 10.11900/0412.1961.2022.00039
[12] Li F L, Fu R, Bai Y R, et al. Effects of initial grain size and strengthening phase on thermal deformation and recrystallization behavior of GH4096 superalloy[J]. Acta Metall. Sin., 2023, 59: 855
doi: 10.11900/0412.1961.2021.00532
李福林, 付 锐, 白云瑞 等. 初始晶粒尺寸和强化相对GH4096高温合金热变形行为和再结晶的影响[J]. 金属学报, 2023, 59: 855
doi: 10.11900/0412.1961.2021.00532
[13] Khan M A, Wang Y W, Hamza M, et al. Precipitation behaviour in an Al-Zn-Mg-Cu alloy subjected to high strain rate compression tests[J]. Mater. Charact., 2021, 180: 111398
doi: 10.1016/j.matchar.2021.111398
[14] Wang Y X, Zhao H, Chen X R, et al. The effect of shearable clusters and precipitates on dynamic recovery of Al alloys[J]. Acta Mater., 2024, 265: 119643
doi: 10.1016/j.actamat.2023.119643
[15] Wang H, Qin G L, Li C A, et al. Effect of deformation parameters and Al2Cu evolution on dynamic recrystallization of 2219-O Al alloy during hot compression[J]. J. Mater. Res. Technol., 2023, 26: 4093
doi: 10.1016/j.jmrt.2023.08.167
[16] Chen J S, Rong L, Huang H, et al. The effects of η phases and Al3(Er, Zr) particles pre-precipitation on the hot workability and recrystallization of Al-Zn-Mg-Er-Zr alloy[J]. J. Mater. Res. Technol., 2024, 29: 2414
doi: 10.1016/j.jmrt.2024.01.223
[17] Han B S, Wei L J, Xu Y J, et al. Effect of pre-deformation on microstructure and mechanical properties of ultra-high strength Al-Zn-Mg-Cu alloy after ageing treatment[J]. Acta Metall. Sin., 2020, 56: 1007
doi: 10.11900/0412.1961.2019.00402
韩宝帅, 魏立军, 徐严谨 等. 预变形对超高强Al-Zn-Mg-Cu合金时效组织与力学性能的影响[J]. 金属学报, 2020, 56: 1007
doi: 10.11900/0412.1961.2019.00402
[18] Yao Y C, Euesden R, Curd M E, et al. Effect of cooling rate on the composition and chemical heterogeneity of quench-induced grain boundary η-phase precipitates in 7xxx aluminium alloys[J]. Acta Mater., 2024, 262: 119443
doi: 10.1016/j.actamat.2023.119443
[19] Xu Y T, Toda H, Shimizu K, et al. Suppressed hydrogen embrittlement of high-strength Al alloys by Mn-rich intermetallic compound particles[J]. Acta Mater., 2022, 236: 118110
doi: 10.1016/j.actamat.2022.118110
[20] Zhang X Z, Zhou D S, Li Y, et al. Concurrent dynamic strain aging and dynamic precipitation evades strength-ductility trade-off in a high Mg-content aluminum crossover alloy[J]. Mater. Sci. Eng., 2022, A854: 143800
[21] Shin J H, Rim G Y, Kim S D, et al. Effects of aging heat-treatment on dynamic strain aging behavior in high-Mn lightweight steel[J]. Mater. Charact., 2020, 164: 110316
doi: 10.1016/j.matchar.2020.110316
[22] Zou Y, Cao L F, Wu X D, et al. Unusual secondary precipitation within the primary precipitation free zone substantially enhances the ductility of Al-Zn-Mg-Cu alloy[J]. Mater. Sci. Eng., 2023, A881: 145384
[23] Ban Y J, Zhang Y, Jia Y L, et al. Effects of Cr addition on the constitutive equation and precipitated phases of copper alloy during hot deformation[J]. Mater. Des., 2020, 191: 108613
doi: 10.1016/j.matdes.2020.108613
[24] Tang J, Wang J H, Teng J, et al. Effect of Zn content on the dynamic softening of Al-Zn-Mg-Cu alloys during hot compression deformation[J]. Vacuum, 2021, 184: 109941
doi: 10.1016/j.vacuum.2020.109941
[25] Wu C H, Feng D, Zang Q H, et al. Microstructure evolution and recrystallization behavior during hot deformation of spray formed AlSiCuMg alloy[J]. Acta Metall. Sin., 2022, 58: 932
doi: 10.11900/0412.1961.2021.00329
吴彩虹, 冯 迪, 臧千昊 等. 喷射成形AlSiCuMg合金的热变形组织演变及再结晶行为[J]. 金属学报, 2022, 58: 932
doi: 10.11900/0412.1961.2021.00329
[26] Liu L L, Zhao G Q, Wang G C, et al. Hot deformation behavior and microstructure evolution model of 7055 aluminum alloy[J]. J. Mater. Res. Technol., 2023, 27: 3191
doi: 10.1016/j.jmrt.2023.10.165
[27] Zhao J H, Deng Y L, Tang J G. Grain refining with DDRX by isothermal MDF of Al-Zn-Mg-Cu alloy[J]. J. Mater. Res. Technol., 2020, 9: 8001
doi: 10.1016/j.jmrt.2020.05.033
[28] Li Y B, Gu B, Jiang S, et al. A CDRX-based material model for hot deformation of aluminium alloys[J]. Int. J. Plast., 2020, 134: 102844
doi: 10.1016/j.ijplas.2020.102844
[29] Wan Z P, Wang T, Sun Y, et al. Dynamic softening mechanisms of GH4720Li alloy during hot deformation[J]. Acta Metall. Sin., 2019, 55: 213
万志鹏, 王 涛, 孙 宇 等. GH4720Li合金热变形过程动态软化机制[J]. 金属学报, 2019, 55: 213
doi: 10.11900/0412.1961.2018.00179
[30] Wang K Z, Zhang C S, Cheng Z N, et al. Dynamic evolution of the T1 phase and its effect on continuous dynamic recrystallization in Al-Cu-Li alloys[J]. Int. J. Plast., 2024, 175: 103948
doi: 10.1016/j.ijplas.2024.103948
[31] Yan S L, Yang H, Li H W, et al. Variation of strain rate sensitivity of an aluminum alloy in a wide strain rate range: Mechanism analysis and modeling[J]. J. Alloys Compd., 2016, 688: 776
doi: 10.1016/j.jallcom.2016.07.077
[32] Huang K, Logé R E. A review of dynamic recrystallization phenomena in metallic materials[J]. Mater. Des., 2016, 111: 548
doi: 10.1016/j.matdes.2016.09.012
[33] Zhang C C, Wang C, Zha M, et al. Microstructure and tensile properties of rolled Mg-4Al-2Sn-1Zn alloy with pre-rolling deformation[J]. Mater. Sci. Eng., 2018, A719: 132
[34] Zhang X, Luo Z A, Xie G M, et al. Interface microstructure and bonding mechanisms of 7050 aluminum alloy thick plates produced by vacuum roll cladding[J]. Mater. Sci. Eng., 2022, A850: 143582
[35] He D G, Xie H, Lin Y C, et al. Microstructure evolution mechanisms and a physically-based constitutive model for an Al-Zn-Mg-Cu-Zr aluminum alloy during hot deformation[J]. J. Mater. Res. Technol., 2023, 26: 4739
doi: 10.1016/j.jmrt.2023.08.203
[36] Wu J F, He D G, Lin Y C, et al. A unified constitutive model and microstructure evolution of a solution treated 7075 aluminum alloys under warm forming condition[J]. J. Mater. Res. Technol., 2024, 30: 4159
doi: 10.1016/j.jmrt.2024.04.101
[37] Xu S, Zhang H M, Xiao N M, et al. Mechanisms of macrozone elimination and grain refinement of near α Ti alloy via the spheroidization of the Widmannstätten structure[J]. Acta Mater., 2023, 260: 119339
doi: 10.1016/j.actamat.2023.119339
[38] Pu J, Zhang C H, Zhu W G, et al. Mechanisms for dynamic recrystallization in a β-quenched Zr-1Nb-1Sn-0.1Fe alloy during hot compression[J]. Mater. Charact., 2024, 212: 113932
doi: 10.1016/j.matchar.2024.113932
[1] YIN Jiannian, MA Yingjie, YANG Rui, LEI Jiafeng, QI Min, ZHOU Li. Hot Deformation Behavior and Hot Processing Map Construction of the Ti551 Alloy[J]. 金属学报, 2026, 62(8): 1427-1442.
[2] ZHOU Jiaxuan, SI Hongli, ZHANG Guilin, ZHANG Shaohua, ZHANG Jian, TIAN Yanzhong, PANG Xueyong. Effect of Heat Treatment on Flame Retardant Property of GH4169 Alloy Fabricated by Selective Laser Melting[J]. 金属学报, 2026, 62(8): 1385-1394.
[3] JIANG Lei, ZHOU Taiwentao, ZHANG Xinbiao, XIAO Xingyu, ZHANG Zhihao, XIE Jianxin. Effect of Natural Aging on the Artificial Aging Behavior of a New Al-Zn-Mg-Cu Alloy[J]. 金属学报, 2026, 62(2): 383-396.
[4] ZHANG Zhefeng, HOU Jiapeng, LIU Rui, LI Xiaotao, ZHANG Zhenjun, ZHANG Peng. Quantitative Relationships Between the Strength-Plasticity and Strength-Electrical Conductivity of Metallic Materials[J]. 金属学报, 2026, 62(2): 253-262.
[5] LONG Fei, LIU Qu, ZHU Yixing, ZHOU Mengran, CHEN Gaoqiang, SHI Qingyu. Microstructure and Corrosion Resistance of Modified Mg-5Zn Alloy via Friction Stir Processing[J]. 金属学报, 2025, 61(7): 1071-1081.
[6] JIANG Muchi, GONG Jishuang, YANG Xingyuan, REN Dechun, CAI Yusheng, LI Bingyang, JI Haibin, LEI Jiafeng. Hot Deformation Behavior of Ti30Ni50Hf20 High-Temperature Shape Memory Alloy[J]. 金属学报, 2025, 61(6): 857-865.
[7] BAO Chengli, LI Hao, HU Li, ZHOU Tao, TANG Ming, HE Qubo, LIU Xiangguo. Construction of Hot Processing Map of Solutionized Mg-10Gd-6Y-1.5Zn-0.5Zr Alloy and Microstructure Evolution[J]. 金属学报, 2025, 61(4): 632-642.
[8] LI Dan, GONG Delun, HAO Yulin. Effect of O Content on the Aging Precipitation Behavior and Mechanical Properties of Ti2448 Alloy[J]. 金属学报, 2025, 61(12): 1790-1802.
[9] LIU Guanghui, WANG Weiguo, Rohrer Gregory S, CHEN Song, LIN Yan, TONG Fang, FENG Xiaozheng, ZHOU Bangxin. {111}/{111} Near Singular Boundaries in a Dynamically Recrystallized Al-Zn-Mg-Cu Alloy Compressed at Elevated Temperature[J]. 金属学报, 2024, 60(9): 1165-1178.
[10] KE Yubin, LI Bin, DUAN Huiping. Morphology and Chemical Composition of Nanoprecipitate in AerMet100 Steel by Separation of the Nuclear and Magnetic Small-Angle Neutron Scattering Data[J]. 金属学报, 2024, 60(8): 1109-1118.
[11] XU Renjie, TU Xin, HU Bin, LUO Haiwen. Microstructure and Mechanical Properties of Cu-V Dual Alloyed 3Mn Steel[J]. 金属学报, 2024, 60(6): 817-825.
[12] LI Longjian, LI Rengeng, ZHANG Jiajun, CAO Xinghao, KANG Huijun, WANG Tongmin. Effects of Cryorolling on Properties and Precipitation Behavior of a High-Strength and High-Conductivity Cu-1Cr-0.2Zr-0.25Nb Alloy[J]. 金属学报, 2024, 60(3): 405-416.
[13] ZHENG Xiong, LAI Yuxiang, XIANG Xuemei, CHEN Jianghua. Impacts of Rare Earth Element La on Properties and Microstructure of AlMgSi Alloys[J]. 金属学报, 2024, 60(1): 107-116.
[14] WANG Zongpu, WANG Weiguo, Rohrer Gregory S, CHEN Song, HONG Lihua, LIN Yan, FENG Xiaozheng, REN Shuai, ZHOU Bangxin. {111}/{111} Near Singular Boundaries in an Al-Zn-Mg-Cu Alloy Recrystallized After Rolling at Different Temperatures[J]. 金属学报, 2023, 59(7): 947-960.
[15] LU Yuhua, WANG Haizhou, LI Dongling, FU Rui, LI Fulin, SHI Hui. A Quantitative and Statistical Method of γ' Precipitates in Superalloy Based on the High-Throughput Field Emission Scanning Eelectron Microscope[J]. 金属学报, 2023, 59(7): 841-854.
No Suggested Reading articles found!