GH4720Li合金热变形过程动态软化机制

doi:10.11900/0412.1961.2018.00179

金属学报

2019, Vol. 55

Issue (2): 213-222 DOI: 10.11900/0412.1961.2018.00179

本期目录 | 过刊浏览

GH4720Li合金热变形过程动态软化机制

万志鹏^1,²(

), 王涛¹, 孙宇², 胡连喜², 李钊¹, 李佩桓¹, 张勇¹

1 中国航发北京航空材料研究院先进高温结构材料重点实验室北京 100095
2 哈尔滨工业大学金属精密热加工国家级重点实验室哈尔滨 150001

Dynamic Softening Mechanisms of GH4720Li AlloyDuring Hot Deformation

Zhipeng WAN^1,²(

), Tao WANG¹, Yu SUN², Lianxi HU², Zhao LI¹, Peihuan LI¹, Yong ZHANG¹

1 Science and Technology on Advanced High Temperature Structural Materials Laboratory, AEEC Beijing Institute of Aeronautical Materials, Beijing 100095, China
2 National Key Laboratory for Precision Hot Processing of Metals, Harbin Institute of Technology, Harbin 150001, China

引用本文:

万志鹏, 王涛, 孙宇, 胡连喜, 李钊, 李佩桓, 张勇. GH4720Li合金热变形过程动态软化机制[J]. 金属学报, 2019, 55(2): 213-222.
Zhipeng WAN, Tao WANG, Yu SUN, Lianxi HU, Zhao LI, Peihuan LI, Yong ZHANG. Dynamic Softening Mechanisms of GH4720Li AlloyDuring Hot Deformation[J]. Acta Metall Sin, 2019, 55(2): 213-222.

全文: PDF(16376 KB) HTML

摘要:

以锻态GH4720Li镍基沉淀强化型高温合金为研究对象,对合金进行了不同工艺参数下的热压缩实验。采用OM、SEM、EBSD和TEM研究了热压缩过程中再结晶晶粒的形成和晶粒内亚结构的演变规律,分析了合金在不同热变形工艺参数下的动态软化机制。研究表明,合金在所有热变形工艺参数下均发生了非连续动态再结晶行为。变形组织分析表明,高温低应变速率能够抑制非连续动态再结晶行为的发生,而提高应变速率能促进非连续动态再结晶行为,且能够获得等轴状尺寸均匀的晶粒组织。未完全溶解细小γ'强化相的钉扎作用能够使变形晶粒内形成高密度位错亚结构和亚晶界,亚晶界角度通过连续的吸收位错而不断地升高,进而以“强化相诱发连续动态再结晶”方式形成细小的再结晶晶粒组织。不同热变形工艺下孪晶界的演变规律分析表明,热变形温度与应变速率通过影响合金的动态再结晶行为来改变孪晶界的数量。

关键词 ： GH4720Li合金, 热压缩实验, 动态软化机制, 强化相诱发连续动态再结晶, 孪晶界

Abstract：

GH4720Li alloy is a precipitation strengthened Ni-based superalloy and widely applied in high performance applications such as disks and blades of either aircraft engines or land-based gas turbines attributing to its excellent properties including resistance to creep and fatigue, together with corrosion, fracture and microstructural stability for the intended applications. Hot working is an effective way for shaping metals and alloys as well as changing the microstructure and mechanical properties. Lots of typical metallurgical behaviors such as dynamic recovery (DRV), discontinuous dynamic recrystallization (DDRX) and continuous dynamic recrystallization (CDRX) occur, which are related to the hot working parameters, including deformation temperature, strain rate and strain. In order to investigate the effect of deformation parameters on dynamic softening behavior and evolution of twinning for GH4720Li alloy, the hot deformation behavior of as-forged GH4720Li alloy was studied by isothermal compression tests. OM, SEM, EBSD and TEM techniques were employed to investigate systematically the dynamic softening mechanisms, formation of DRX grains and evolution of substructure in grains under different deformation parameters. The results showed that DDRX can take place at all studied deformation conditions. The boundary bulging and nucleation of DDRX grains were restrained as a result of decrease of dislocation substructures and subgrain boundaries density consumed by continuous original boundary migration (COBM) in deformed grains at low strain rates and high temperatures, and then the occurrence of DDRX was suppressed. DDRX was promoted as the strain rate was increased and uniform microstructures composed of fine equiaxed grains can be readily obtained as well. The microstructural changes showed that the pinning effect of fine undissolved γ' precipitates was able to hinder the dislocation movement and promote the formation of high density of dislocation substructures and subgrain boundaries in deformed grains. The increase in sub-boundary misorientation brought about by continuous accumulation of the dislocations was introduced by the deformation, and fine DRX grains formed by particle-induced continuous dynamic recrystallization (PI-CDRX). According to the evolution of twinning under various deformation conditions, the effect of deformation temperature and strain rate on the evolution of twinning was characterized by the occurrence of DRX behavior.

Key words： GH4720Li alloy hot compression test dynamic softening mechanism particle-induced CDRX twinning boundary

收稿日期: 2018-05-04

ZTFLH:

TG146.1

作者简介:

作者简介万志鹏,男,1991年生,博士生

	服务

	把本文推荐给朋友
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	万志鹏
	王涛
	孙宇
	胡连喜
	李钊
	李佩桓
	张勇
44.8K

链接本文:

https://www.ams.org.cn/CN/10.11900/0412.1961.2018.00179 或 https://www.ams.org.cn/CN/Y2019/V55/I2/213

图1 GH4720Li合金初始锻造态微观组织

图2 GH4720Li合金不同应变速率下软化应力与变形温度之间的关系曲线

图3 应变速率为10 s-1、应变量为0.8下GH4720Li合金的SEM像

图4 应变速率为1 s-1、应变量为0.8下GH4720Li合金的OM像

图5 变形温度为1100 ℃、应变量为0.8下GH4720Li合金的OM像

图6 不同热变形参数条件下GH4720Li合金的TEM像

图7 热变形温度为1060 ℃、应变速率为1 s-1下GH4720Li合金的EBSD图

图8 取向角沿图7a中直线段分布图

图9 热变形温度为1100 ℃、应变为0.8下GH4720Li合金的EBSD图

图10 应变速率为0.1 s-1、应变为0.8下GH4720Li合金的EBSD图

图11 不同热变形工艺参数下合金软化机制变化示意图

图12 应变速率与温度对GH4720Li合金孪晶界形成的影响

[1]	Furrer D U, Fecht H J.γ′ formation in superalloy U720Li[J]. Scr. Mater., 1999, 40: 1215
[2]	Radis R, Schaffer M, Albu M, et al.Multimodal size distributions of γ′ precipitates during continuous cooling of Udimet 720 Li[J]. Acta Mater., 2009, 57: 5739
[3]	Chen J Y, Dong J X, Zhang M C, et al.Deformation mechanisms in a fine-grained Udimet 720Li nickel-base superalloy with high volume fractions of γ′ phases[J]. Mater. Sci. Eng., 2016, A673: 122
[4]	Liu F F, Chen J Y, Dong J X, et al.The hot deformation behaviors of coarse, fine and mixed grain for Udimet 720Li superalloy[J]. Mater. Sci. Eng., 2016, A651: 102
[5]	Sakai T, Belyakov A, Kaibyshev R, et al.Dynamic and post-dynamic recrystallization under hot, cold and severe plastic deformation conditions[J]. Prog. Mater. Sci., 2014, 60: 130
[6]	Zhou G W, Li Z H, Li D Y, et al.A polycrystal plasticity based discontinuous dynamic recrystallization simulation method and its application to copper[J]. Int. J. Plast., 2017, 91: 48
[7]	He G A, Tan L M, Liu F, et al.Unraveling the formation mechanism of abnormally large grains in an advanced polycrystalline nickel base superalloy[J]. J. Alloys Compd., 2017, 718: 405
[8]	Zhang L, Wang Q D, Liu G P, et al.Effect of SiC particles and the particulate size on the hot deformation and processing map of AZ91 magnesium matrix composites[J]. Mater. Sci. Eng., 2017, A707: 315
[9]	Huang K, Marthinsen K, Zhao Q L, et al.The double-edge effect of second-phase particles on the recrystallization behaviour and associated mechanical properties of metallic materials[J]. Prog. Mater. Sci., 2018, 92: 284
[10]	Li F L, Fu R, Yin F J, et al.Impact of γ′(Ni3(Al, Ti)) phase on dynamic recrystallization of a Ni-based disk superalloy during isothermal compression[J]. J. Alloys Compd., 2017, 693: 1076
[11]	Yu Q Y, Yao Z H, Dong J X.Deformation and recrystallization behavior of a coarse-grain, nickel-base superalloy Udimet 720Li ingot material[J]. Mater. Charact., 2015, 107: 398
[12]	Wan Z P, Sun Y, Hu L X, et al.Experimental study and numerical simulation of dynamic recrystallization behavior of TiAl-based alloy[J]. Mater. Des., 2017, 122: 11
[13]	Yuan X Y, Chen L Q.Hot deformation at elevated temperature and recrystallization behavior of a high manganese austenitic TWIP steel[J]. Acta Metall. Sin., 2015, 51: 651(袁晓云, 陈礼清. 一种高锰奥氏体TWIP钢的高温热变形与再结晶行为[J]. 金属学报, 2015, 51: 651)
[14]	Li Q, Guo H Z, Wang Y W, et al.Hot deformation behaviors and microstructure evolution of GH4049 alloy[J]. J. Mater. Eng., 2014, (12): 55(李卿, 郭鸿镇, 王彦伟等. GH4049合金的热变形行为及组织演变[J]. 材料工程, 2014, (12): 55)
[15]	Yang Z Q, Liu Z D, He X K, et al.Hot deformation behavior of SA508Gr.4N steel for reactor pressure vessels[J]. J. Mater. Eng., 2017, 45(8): 88(杨志强, 刘正东, 何西扣等. 反应堆压力容器用SA508Gr.4N钢的热变形行为[J]. 材料工程, 2017, 45(8): 88)
[16]	Monajati H, Jahazi M, Bahrami R, et al.The influence of heat treatment conditions on γ′ characteristics in Udimet? 720[J]. Mater. Sci. Eng., 2004, A373: 286
[17]	Hallberg H, Svendsen B, Kayser T, et al.Microstructure evolution during dynamic discontinuous recrystallization in particle-containing Cu[J]. Comput. Mater. Sci., 2014, 84: 327
[18]	Han Y, Yan S, Yin B G, et al.Effects of temperature and strain rate on the dynamic recrystallization of a medium-high-carbon high-silicon bainitic steel during hot deformation[J]. Vacuum, 2018, 148: 78
[19]	Ahmed K, Tonks M, Zhang Y F, et al.Particle-grain boundary interactions: A phase field study[J]. Comput. Mater. Sci., 2017, 134: 25
[20]	Langelier B, Persaud S Y, Korinek A, et al.Effects of boundary migration and pinning particles on intergranular oxidation revealed by 2D and 3D analytical electron microscopy[J]. Acta Mater., 2017, 131: 280
[21]	Mousavizade S M, Pouranvari M, Ghaini F M, et al.Dynamic recrystallization phenomena during laser-assisted friction stir processing of a precipitation hardened nickel base superalloy[J]. J. Alloys Compd., 2016, 685: 806
[22]	Doherty R D, Hughes D A, Humphreys F J, et al.Current issues in recrystallization: A review[J]. Mater. Sci. Eng., 1997, A238: 219
[23]	Zhilyaev A P, Langdon T G.Using high-pressure torsion for metal processing: Fundamentals and applications[J]. Prog. Mater. Sci., 2008, 53: 893
[24]	Rout M, Ranjan R, Pal S K, et al.EBSD study of microstructure evolution during axisymmetric hot compression of 304LN stainless steel[J]. Mater. Sci. Eng., 2018, A711: 378
[25]	Son K T, Kim M H, Kim S W, et al.Evaluation of hot deformation characteristics in modified AA5052 using processing map and activation energy map under deformation heating[J]. J. Alloys Compd., 2018, 740: 96
[26]	Yin X Q, Park C H, Li Y F, et al.Mechanism of continuous dynamic recrystallization in a 50Ti-47Ni-3Fe shape memory alloy during hot compressive deformation[J]. J. Alloys Compd., 2017, 693: 426
[27]	Kapoor R, Reddy G B, Sarkar A.Discontinuous dynamic recrystallization in α-Zr[J]. Mater. Sci. Eng., 2018, A718: 104
[28]	Hadadzadeh A, Mokdad F, Wells M A, et al.A new grain orientation spread approach to analyze the dynamic recrystallization behavior of a cast-homogenized Mg-Zn-Zr alloy using electron backscattered diffraction[J]. Mater. Sci. Eng., 2018, A709: 285
[29]	Pradhan S K, Mandal S, Athreya C N, et al.Influence of processing parameters on dynamic recrystallization and the associated annealing twin boundary evolution in a nickel base superalloy[J]. Mater. Sci. Eng., 2017, A700: 49
[30]	Azarbarmas M, Aghaie-Khafri M, Cabrera J M, et al.Dynamic recrystallization mechanisms and twining evolution during hot deformation of Inconel 718[J]. Mater. Sci. Eng., 2016, A678: 137
[31]	Li Z G, Zhang L T, Sun N R, et al.Effects of prior deformation and annealing process on microstructure and annealing twin density in a nickel based alloy[J]. Mater. Charact., 2014, 95: 299
[32]	Zhang H B, Zhang K F, Zhou H P, et al.Effect of strain rate on microstructure evolution of a nickel-based superalloy during hot deformation[J]. Mater. Des., 2015, 80: 51
[33]	Aghaie-Khafri M, Mahmudi R.Optimizing homogenization parameters for better stretch formability in an Al-Mn-Mg alloy sheet[J]. Mater. Sci. Eng., 2005, A399: 173

[1]	刘超, 姚志浩, 江河, 董建新. GH4720Li合金毫米级粗大晶粒热变形获得均匀等轴晶粒的可行性及工艺控制[J]. 金属学报, 2021, 57(10): 1309-1319.
[2]	王涛,万志鹏,李钊,李佩桓,李鑫旭,韦康,张勇. 热处理工艺对GH4720Li合金细晶铸锭组织与热加工性能的影响[J]. 金属学报, 2020, 56(2): 182-192.
[3]	钟茜婷, 王磊, 刘峰. Incoloy 028合金不连续动态再结晶中链状组织形成机理研究[J]. 金属学报, 2018, 54(7): 969-980.
[4]	刘廷光, 夏爽, 白琴, 周邦新, 陆永浩. 孪晶界在316L不锈钢三维晶界网络中的分布特征[J]. 金属学报, 2018, 54(10): 1377-1386.
[5]	王涛, 万志鹏, 孙宇, 李钊, 张勇, 胡连喜. 镍基变形高温合金动态软化行为与组织演变规律研究[J]. 金属学报, 2018, 54(1): 83-92.
[6]	梁后权, 郭鸿镇, 宁永权, 姚泽坤, 赵张龙. 基于软化机制的TC18钛合金本构关系研究^*[J]. 金属学报, 2014, 50(7): 871-878.
[7]	魏宇杰. 纳米金属材料的界面力学行为研究^*[J]. 金属学报, 2014, 50(2): 183-190.
[8]	周昊飞, 曲绍兴. 利用分子动力学研究梯度纳米孪晶Cu的微观变形机理^*[J]. 金属学报, 2014, 50(2): 226-230.
[9]	王媛媛, 陈立佳, 王宝森. 温度对625镍基高温合金焊接接头低周疲劳行为的影响[J]. 金属学报, 2014, 50(12): 1485-1490.
[10]	赵帅李秀艳戎利建. 一种奥氏体FeNi基合金中的锯齿流变现象[J]. 金属学报, 2011, 47(8): 1017-1021.
[11]	贾斌彭艳. 铌微合金钢高温变形的本构关系[J]. 金属学报, 2011, 47(4): 507-512.
[12]	张哲峰张鹏田艳中张青科屈伸邹鹤飞段启强李守新王中光. 金属材料疲劳损伤的界面效应[J]. 金属学报, 2009, 45(7): 788-800.
[13]	唐恋卢磊. 孪晶片层厚度对纳米孪晶Cu疲劳性能的影响[J]. 金属学报, 2009, 45(7): 808-814.
[14]	张伟红; 张士宏 . NiTi合金热压缩实验数据的修正及其本构方程[J]. 金属学报, 2006, 42(10): 1036-1040 .
[15]	刘明; 张修睦 . Cu-Zn-Al双程记忆合金中Ⅱ类孪晶的界面观察[J]. 金属学报, 1999, 35(4): 371-374 .

Viewed

Full text

Abstract

Cited

Shared

Discussed