Please wait a minute...
金属学报  1989, Vol. 25 Issue (6): 55-59    
  论文 本期目录 | 过刊浏览 |
低周疲劳过程中热作模具钢的循环软化特征与机制
胡镇华;肖杰轩
华中理工大学;副教授;武汉(430074);华中理工大学
CYCLIC SOFTENING IN HOT-WORKING DIE STEELS DURING LOW CYCLE FATIGUE
HU Zhenhua;XIAO Jiexuan Huazhong University of Science and Technology; Wuhan HU Zhenhua; associate professor; Huazhong University of Science and Technology;Wuhan 430074
引用本文:

胡镇华;肖杰轩. 低周疲劳过程中热作模具钢的循环软化特征与机制[J]. 金属学报, 1989, 25(6): 55-59.
, . CYCLIC SOFTENING IN HOT-WORKING DIE STEELS DURING LOW CYCLE FATIGUE[J]. Acta Metall Sin, 1989, 25(6): 55-59.

全文: PDF(1414 KB)  
摘要: 在应变控制下,试验了5CrNiMo和5Cr2NiMoVSi两种热作模具钢的循环软化特性及其微观结构的变化。结果表明:在应变幅为Δεt/2=0.6—1.8×10~(-2)范围内,不同硬化状态的试验钢均表现为循环软化特性;软化效应主要集中在前几周,在随后的循环过程中应力幅变化较小,软化效应减弱;整个循环过程中,未观察到明显的应力饱和现象。TEM分析表明,循环软化与塑性变形的不均匀性有关。试验钢的软化是由于在循环变形中位错结构转变成低密度、低内应力的位错胞状组织,以及细小碳化物在位错往复切割下碎化而重新回溶引起的。
关键词 低周疲劳热作模具钢循环软化    
Abstract:The feature and microstructure change of cyclic softening in hot-working die steels 5CrNiMo and 5Cr2NiMoVSi were studied under strain controlledlow-cycle fatiguing. The results show that the cyclic softening is featured in bothvariedly hardened steels under strain controlled in the amplitude range of Δε_t,/2=0.6 - 1.8×10~(-2). The softening effect is mainly gathered in the prior some cycles.And the stress amplitude varies slightly in the sequential cycles, i. e. the softeningeffect is minified. No obvious saturation phenomenon of stress is observed duringthe whole cyclic deformation. The cyclic softening was analyzed under TEM thatit is related to heterogeneity of plastic deformation. The softening of the steelstested is caused by the formation or the dislocation cell structure with low densityand low internal stress, and by the redissolution of fine carbides into matrix.
Key wordslow-cycle fatigue    hot-working die steel    cyclic softening
收稿日期: 1989-06-18     
1 胡翔,林颜盛,黄正安,冯干江,许玉贤.金属学报,1987;23:A369
2 夏月波,王中光.第三届全国疲劳学术交流会论文集(第V册),桂林:中国机械工程学会,中国力学学会,中国航空学会,中国金属学会,1986:V4-2-1
3 Nahm H, Moteff J, Diercks D R. Acta Metall, 1977; 25: 107
4 Borchert B. In: Cautsouradis D, Pelix P. Fischmeister H, et al eds., High Temperature Alloys for Gas Turbines, London: Applied Science, 1978: 573
5 Landgraf R W. ASTM STP467, 1970: 3
6 Macherauch E,杨全译.材料科学与工程,1987;(4) :14
7 McGrath J T, Bratina W J. Czech J Phys, 1969; B19: 284
[1] 周红伟, 高建兵, 沈加明, 赵伟, 白凤梅, 何宜柱. 高温低周疲劳下C-HRA-5奥氏体耐热钢中孪晶界演变[J]. 金属学报, 2022, 58(8): 1013-1023.
[2] 周红伟, 白凤梅, 杨磊, 陈艳, 方俊飞, 张立强, 衣海龙, 何宜柱. 1100 MPa级高强钢的低周疲劳行为[J]. 金属学报, 2020, 56(7): 937-948.
[3] 张哲峰,邵琛玮,王斌,杨浩坤,董福元,刘睿,张振军,张鹏. 孪生诱发塑性钢拉伸与疲劳性能及变形机制[J]. 金属学报, 2020, 56(4): 476-486.
[4] 张哲峰, 刘睿, 张振军, 田艳中, 张鹏. 金属材料疲劳性能预测统一模型探索[J]. 金属学报, 2018, 54(11): 1693-1704.
[5] 安金岚,王磊,刘杨,胥国华,赵光普. 长期时效对GH4169合金组织演化及低周疲劳行为的影响*[J]. 金属学报, 2015, 51(7): 835-843.
[6] 车欣, 梁兴奎, 陈丽丽, 陈立佳, 李锋. Al-9.0%Si-4.0%Cu-0.4%Mg(-0.3%Sc)合金的显微组织及其低周疲劳行为*[J]. 金属学报, 2014, 50(9): 1046-1054.
[7] 张思倩, 吴伟, 陈丽丽, 车欣, 陈立佳. 热处理对挤压变形Mg-7%Zn-0.6%Zr-0.5%Y合金低周疲劳行为的影响*[J]. 金属学报, 2014, 50(6): 700-706.
[8] 郭鹏程, 钱立和, 孟江英, 张福成. 高锰奥氏体TWIP钢的单向拉伸与拉压循环变形行为*[J]. 金属学报, 2014, 50(4): 415-422.
[9] 王媛媛, 陈立佳, 王宝森. 温度对625镍基高温合金焊接接头低周疲劳行为的影响[J]. 金属学报, 2014, 50(12): 1485-1490.
[10] 于慧臣,董成利,焦泽辉,孔凡涛,陈玉勇,苏勇君. 一种TiAl合金的高温蠕变和疲劳行为及其寿命预测方法[J]. 金属学报, 2013, 49(11): 1311-1317.
[11] 张莹 张义文 张娜 刘明东 刘建涛. 粉末冶金高温合金FGH97的低周疲劳断裂特征[J]. 金属学报, 2010, 46(4): 444-450.
[12] 王航 徐燕灵 孙巧艳 肖林 孙军. 细晶Ti--2Al--2.5Zr合金室温/低温低周疲劳行为及微观结构[J]. 金属学报, 2009, 45(4): 434-441.
[13] 黄志伟; 袁福河; 王中光; 朱世杰; 王富岗 . 铸造镍基高温合金M963的高温低周疲劳行为[J]. 金属学报, 2007, 43(7): 678-682 .
[14] 黄志伟; 袁福河; 王中光; 朱世杰; 王富岗 . M38镍基高温合金高温低周疲劳性能及断裂机制[J]. 金属学报, 2007, 43(10): 1025-1030 .
[15] 陈凌; 蒋家羚; 范志超; 陈学东; 杨铁成 . 低周疲劳寿命预测的能量模型探讨[J]. 金属学报, 2006, 42(2): 195-200 .