Please wait a minute...
金属学报  2026, Vol. 62 Issue (5): 770-784    DOI: 10.11900/0412.1961.2025.00381
  综述 本期目录 | 过刊浏览 |
难加工金属增材制造/热等静压融合成形研究现状与展望
史玉升1, 程焜1, 张程健1, 卢佳浩1, 李伟2, 张李超1, 魏青松1, 蔡超1()
1 华中科技大学 材料成形与模具技术全国重点实验室 武汉 430074
2 武汉科技大学 机械工程学院 武汉 430081
Research Status and Prospects of Additive Manufacturing/Hot Isostatic Pressing Integrated Forming for Difficult-to-Machine Metals
SHI Yusheng1, CHENG Kun1, ZHANG Chengjian1, LU Jiahao1, LI Wei2, ZHANG Lichao1, WEI Qingsong1, CAI Chao1()
1 State Key Laboratory of Materials Processing and Die & Mould Technology, Huazhong University of Science and Technology, Wuhan 430074, China
2 School of Mechanical Engineering, Wuhan University of Science and Technology, Wuhan 430081, China
引用本文:

史玉升, 程焜, 张程健, 卢佳浩, 李伟, 张李超, 魏青松, 蔡超. 难加工金属增材制造/热等静压融合成形研究现状与展望[J]. 金属学报, 2026, 62(5): 770-784.
Yusheng SHI, Kun CHENG, Chengjian ZHANG, Jiahao LU, Wei LI, Lichao ZHANG, Qingsong WEI, Chao CAI. Research Status and Prospects of Additive Manufacturing/Hot Isostatic Pressing Integrated Forming for Difficult-to-Machine Metals[J]. Acta Metall Sin, 2026, 62(5): 770-784.

全文: PDF(2068 KB)   HTML
摘要: 

难加工金属通常具有特殊的物理和力学性能,在高温稳定性、高比刚度和轻量化等方面表现突出,对航空航天、能源动力、海洋工程等高端装备领域具有战略意义。本文系统综述了难加工金属增材制造与热等静压融合成形技术的研究进展和发展趋势。聚焦于Be及铍合金、Ti2AlNb合金、高Ti/Al含量镍基高温合金以及金属基复合材料四类典型材料,深入剖析了其在传统加工过程中存在的成形难度大、材料利用率低和组织均匀性差等瓶颈问题。重点阐述了增材制造/热等静压融合技术在多尺度模拟仿真、包套结构补偿设计、高精高密薄壁包套增材制造、高刚易溶失陶瓷型芯制备等方面的关键突破,系统比较了该技术在难加工材料构件近净成形、组织均匀性调控和性能优化方面的显著优势。最后,展望了该技术在包套科学设计、增材制造智能工艺控制及陶瓷型芯性能协同优化等方向的未来发展趋势,以期为推动热等静压成形技术的创新和应用提供理论支撑和实践指导,拓展其在难加工金属复杂构件近终成形中的应用范围,为我国航空航天、国防装备等重点领域核心部件的自主制造提供技术助力。

关键词 : 难加工金属,  热等静压,  增材制造,  近净成形    
Abstract:

Difficult-to-machine metals typically possess unique physical and mechanical properties, such as high-temperature stability, high specific stiffness, and lightweight characteristics. These metals hold strategic significance for high-end equipment sectors such as aerospace, energy and power, and marine engineering. This study systematically reviews the research progress and development trends in the integrated additive manufacturing/hot isostatic pressing (AM/HIP) forming technology for difficult-to-machine metals. The study focuses on the following four typical materials: (i) Be and its alloys, (ii) Ti2AlNb alloys, (iii) nickel-based superalloys with high Ti/Al content, and (iv) metal matrix composites. This study provides an in-depth analysis of the bottlenecks encountered in conventional processing, such as high forming difficulty, low material utilization, and poor microstructural homogeneity. Furthermore, the study highlights key research breakthroughs in the integrated AM/HIP technology, including multiscale HIP simulation, compensation design methods for capsule structures, AM of high-precision and high-density thin-walled capsules, and AM of high-strength soluble ceramic cores. A comparative analysis is performed on the advantages of the technology in the near-net shaping, microstructural homogenization, and performance optimization of components made from difficult-to-machine materials. Finally, future developments for the technology are outlined, including scientific capsule design, intelligent process control for capsule AM, and synergistic optimization of ceramic core properties. This study provides theoretical support and practical pathways to promote the innovative development of HIP forming technology, expanding its application in the near-final forming of complex components made from difficult-to-machine metals, and offering technical assistance for the manufacturing of core components in key sectors in China, such as aerospace and defense equipment.

Key words: difficult-to-machine metal    hot isostatic pressing    additive manufacturing    near-net shape
收稿日期: 2025-11-24     
ZTFLH:  TF125  
基金资助:国家自然科学基金项目(U22A20192);国家自然科学基金项目(52375335);中南大学粉末冶金全国重点实验室资助项目(Sklpm-KF-2025010)
通讯作者: 蔡 超,chaocai@hust.edu.cn,主要从事增材制造、热等静压成形理论与技术研究
Corresponding author: CAI Chao, associate professor, Tel: (027)87557155, E-mail: chaocai@hust.edu.cn
作者简介: 史玉升,男,1962年生,教授,博士
图1  难加工金属的典型应用
图2  增材制造/热等静压(AM/HIP)融合技术示意图
Material categoryGrade or compositionAdvantageous performanceDifficult to process characteristicsApplication

Be and Be alloy

S-200F[29]

(Be ≥ 98.5%),

AlBeMet 162[30]

(Be-38Al)

(1) Specific stiffness: 86-164 GPa·cm3·g-1

(2) Thermal conductivity:210-220 W·m-1·K-1

(3) Coefficient of thermal expansion: (11.5-13.9) × 10-6 K-1

(4) Infrared reflectance: 98%-99%

(1) Low ductility and prone to cracking during casting

(2) High intrinsic brittleness and prone to cracking during machining

(3) Highly toxic and constrained in supply; fully enclosed processing and strict protection are required, leading to high cost and limited capacity

(1) Aerospace field: inertial navigation platforms, gyro components, and lightweight load bearing structures with high stiffness

(2) Optics and semiconductor equipment field: metal mirrors for infrared and astronomical telescopes, EUV lithography mirror substrates

(3) Nuclear and extreme thermal environments: first wall or plasma facing materials for fusion devices and high heat flux thermal management components

Ti2AlNb alloy

Ti-22Al-25Nb[31],

Ti-45Al-5Nb-0.3 W[32],

Ti-22Al-25Nb[33],

Ti2AlNb[34]

(1) Ultimate tensile strength: 880-937 MPa at 650 oC

(2) Elongation: 137%-167% at 900 oC

(3) Fatigue limit: 400-470 MPa at 650-700 oC, 107 cyc

(4) Creep life: 201 h (550 oC, 600 MPa)

(1) Severe cracking is commonly observed during rapid solidification

(2) Process control is challenging, resulting in frequent internal defects in formed parts

(1) Aeroengine field: multiple key components such as aeroengine forgings and blade billets

(2) Medical field: orthopedic hard tissue repair devices such as artificial joints, spinal fusion cages, and bone plates

Ni based superalloy with high Ti and Al contents

CMSX-4[37,40],

IN738LC[35],

CM247LC[36],

Mar-M247[38,39]

(1) Ultimate tensile strength: 1050-1150 MPa at 750 oC

(2) Elongation: 45.5%-55.4% at 900 oC

(3) High temperature fatigue limit: 280-320 MPa at 750 oC, 107 cyc

(4) Creep life: 320 h at 800 oC, 250 MPa

(1) Wide solidification range; the interdendritic liquid film readily induces hot tearing

(2) High thermal gradients and rapid cooling generate significant residual stress and cause cracking

(3) Process control is difficult, making it hard to obtain the desired microstructure directly

(1) Aeroengine field: standard material for high pressure turbine of 4th and 5th generation high thrust turbofan engines, also used for combustors, guide vanes, and related parts

(2) Domestic aero power field: “Taihang” series military turbofan engines

(3) Energy field: suitable for supercritical power plant boiler superheaters

Metal matrix composites

55%*SiC/Al[41],

60%*diamond/Cu[42],

65%*SiC/Cu[43],

30%*B4C/Al[44]

(1) Coefficient of thermal expansion: (6-15.8) × 10-6 K-1

(2) Thermal conductivity: 400-900 W·m-1·K-1

(3) Elastic modulus: 180-472 GPa at RT

(1) Large thermal expansion mismatch between ceramic reinforcement and metal matrix; solidification easily produces thermal stress and induces cracking or porosity

(2) High ceramic fraction leads to brittleness and poor plasticity; severe tool wear during machining and frequent tool chipping

(1) Aerospace field: load bearing and frequently disassembled parts such as aircraft ventral fin skins, fuel inlet covers, internal guide rails, and angle stiffeners

(2) Precision instruments field: load bearing components such as gimbals, brackets, and instrument bay sections for strategic missile systems, as well as laser gyro cavities and optical support structures

(3) Thermal management field: housings and bases for radar T/R modules, baseplates for IGBT power modules, and thin wall packages for optoelectronic and optical communication devices

表1  典型难加工材料的性能优势、加工难点以及应用场景[29~44]
图3  不同工艺成形难加工材料的多维度对比雷达图
图4  AM/HIP融合成形技术的研究突破点
图5  HIP变形模拟和补偿设计全流程示意图
[1] Du Y S, Lu M M, Lin J Q, et al. Investigation on machinability of SiCp/Al composites under the synergistic effect of pulsed laser assisted and ultrasonic elliptical vibration cutting [J]. J. Mater. Process. Technol., 2024, 332: 118561
doi: 10.1016/j.jmatprotec.2024.118561
[2] Pandey K, Datta S. Hot machining of difficult-to-cut materials: A review [J]. Mater. Today: Proc., 2021, 44: 2710
[3] Madhavulu G, Ahmed B. Hot machining process for improved metal removal rates in turning operations [J]. J. Mater. Process. Technol., 1994, 44: 199
doi: 10.1016/0924-0136(94)90432-4
[4] Cheng K, Cao Y D, Liu G Z, et al. Achieving high density and strength enhancement of 55 vol% SiCp/6061Al composites using semi-solid hot isostatic pressing: Liquid fraction optimization and strengthening mechanism [J]. J. Mater. Process. Technol., 2025, 346: 119113
doi: 10.1016/j.jmatprotec.2025.119113
[5] Sanchez L, Ouedraogo E, Dellis C, et al. Influence of container on numerical simulation of hot isostatic pressing: Final shape profile comparison [J]. Powder Metall., 2004, 47: 253
doi: 10.1179/003258904225015608
[6] Xu D M, Qin G W, Li F, et al. Advances in beryllium and beryllium-containing materials [J]. Chin. J. Nonferrous Met., 2014, 24: 1212
[6] 许德美, 秦高梧, 李 峰 等. 国内外铍及含铍材料的研究进展 [J]. 中国有色金属学报, 2014, 24: 1212
[7] Roskill Information Services Ltd. The Economics of Beryllium [M]. London: Roskill Information Services Ltd. Press, 2001: 127
[8] Fenn Jr R W, Glass R A, Needham R A, et al. Beryllium-aluminum alloys [J]. J. Spacecr. Rockets, 1965, 2: 87
doi: 10.2514/3.28126
[9] Zuev S Y, Lopatin A Y, Luchin V I, et al. Comparative study of the thermal stability of Be-based extreme ultraviolet pellicles [J]. Tech. Phys., 2023, 68(Suppl. 3): S630
doi: 10.1134/S106378422390098X
[10] Wikman B, Svoboda A, Häggblad H Å. A combined material model for numerical simulation of hot isostatic pressing [J]. Comput. Methods Appl. Mech. Eng., 2000, 189: 901
doi: 10.1016/S0045-7825(99)00406-5
[11] Lv M Q, Fu Y Q, Yang Z Y, et al. A two-stage constitutive model for Ti2AlNb alloy based on asymptote approach and temperature-corrected stress [J]. J. Mater. Eng. Perform., 2021, 30: 1957
doi: 10.1007/s11665-021-05465-1
[12] Wu B, Chen L, Fu J B, et al. Prediction of phase structure and phase transition of Ti2AlNb-based alloy [J]. Trans. Mater. Heat Treat., 2009, 30(4): 189
[12] 吴 波, 陈 露, 付金彪 等. Ti2AlNb基合金热处理中的相结构与相变预测 [J]. 材料热处理学报, 2009, 30(4): 189
[13] Dong W P, Gao H B, Guo C H, et al. Effect of additive manufacturing process and heat treatment on microstructure and properties of Ti-6Al-4V alloy [J]. J. Aeronaut. Mater., 2022, 42(6): 22
[13] 董万鹏, 高华兵, 果春焕 等. 增材制造工艺及热处理对Ti-6Al-4V合金组织和性能的影响 [J]. 航空材料学报, 2022, 42(6): 22
doi: 10.11868/j.issn.1005-5053.2022.000064
[14] Chen W, Li J W, Xu L, et al. Development of Ti2AlNb alloys: Opportunities and challenges [J]. AM&P Technol. Artic., 2014, 172: 23
[15] Cheng J W, Rao Q L, Li J F, et al. Research progress of microstructure transformation and kinetics in Ti2AlNb-based alloy [J]. J. Aeronaut. Mater., 2022, 42(6): 1
[15] 程剑文, 饶群力, 李金富 等. Ti2AlNb基合金中的组织转变及其动力学研究进展 [J]. 航空材料学报, 2022, 42(6): 1
doi: 10.11868/j.issn.1005-5053.2022.000080
[16] Si Y F, Meng L H, Chen Y Y. Research development of Ti2AlNb-based alloy [J]. Aerosp. Mater. Technol., 2006, 36(3): 10
[16] 司玉锋, 孟丽华, 陈玉勇. Ti2AlNb基合金的研究进展 [J]. 宇航材料工艺, 2006, 36(3): 10
[17] Zhu L, Li J S, Tang B, et al. Flow characteristics and deformation mechanisms for TiAl/Ti2AlNb diffusion bonded joint [J]. Mater. Chem. Phys., 2018, 220: 216
doi: 10.1016/j.matchemphys.2018.08.066
[18] Selvaraj S K, Sundaramali G, Jithin Dev S, et al. Recent advancements in the field of Ni-based superalloys [J]. Adv. Mater. Sci. Eng., 2021, 2021: 9723450
doi: 10.1155/amse.v2021.1
[19] Liang Z Y, Du Y L, Liu Y F, et al. Effect of primary aging treatment temperature on microstructure of two Ni-based single crystal superalloys [J]. Gas Turb. Exp. Res., 2025, 38: 75
[19] 梁昭杨, 杜云玲, 刘砚飞 等. 一级时效热处理温度对两种镍基单晶高温合金组织的影响 [J]. 燃气涡轮试验与研究, 2025, 38: 75
[20] Guo S J, Li J Y, Yuan S Y, et al. High-temperature oxidation behaviors and γʹ phase stability of a new fourth-generation single crystal superalloy with rare earth [J]. Acta Metall. Sin., 2026, 62: 351
[20] 郭世佳, 李健乐, 袁圣云 等. 一种含稀土新型第四代镍基单晶高温合金的高温氧化行为和γʹ相稳定性 [J]. 金属学报, 2026, 62: 351
doi: 10.11900/0412.1961.2024.00243
[21] Xie B, Yu T Y, Luo Z B, et al. A macro-mesoscopic life prediction method of the fatigue short crack in turbine disks based on CP‐XFEM [J]. Fatigue Fract. Eng. Mater. Struct., 2025, 48: 4979
[22] Hou K L, Ou M Q, Xing W W, et al. The formation of η-Ni3Ti phase microstructure in a cast nickel-based superalloy with high Ti/Al ratio [J]. J. Mater. Res. Technol., 2024, 29: 764
doi: 10.1016/j.jmrt.2024.01.156
[23] Yang K, An T, Qu J, et al. Effects of solution cooling rate on the grain boundary and mechanical properties of GH4710 alloy [J]. Mater. Sci. Eng., 2022, A832: 142459
[24] Cheng S Y, Cao Q, Bao J X, et al. Research and development of medium/high volume fraction SiCp/Al composites [J]. Chin. Opt., 2019, 12: 1064
doi: 10.3788/co.
[24] 程思扬, 曹 琪, 包建勋 等. 中高体积分数SiCp/Al复合材料研究进展 [J]. 中国光学, 2019, 12: 1064
[25] Maruyama B. Discontinuously reinforced aluminum: Current status and future direction [J]. JOM, 1999, 51(11): 59
doi: 10.1007/s11837-999-0225-1
[26] Mohn W R, Vukobratovich D. Engineered metal matrix composites for precision optical systems [A]. Proceedings of SPIE 0817, Optomechanical Systems Engineering [C]. San Diego: SPIE, 1987: 181
[27] Mohn W R, Vukobratovich D. Recent applications of metal matrix composites in precision instruments and optical systems [J]. Opt. Eng., 1988, 27: 270290
[28] Cui Y, Li L F, Li J L, et al. High volume fraction SiC/Al composites for space-based optomechanical structures [J]. Opt. Precis. Eng., 2007, 15: 1175
[28] 崔 岩, 李丽富, 李景林 等. 制备空间光机结构件的高体份SiC/Al复合材料 [J]. 光学 精密工程, 2007, 15: 1175
[29] Moons F, Chaouadi R, Puzzolante J L. Fracture behaviour of neutron irradiated beryllium [J]. Fusion Eng. Des., 1998, 41: 187
doi: 10.1016/S0920-3796(98)00137-9
[30] Liu X, Zhang P, Xu Q, et al. Aging behavior of Be/6061Al composite fabricated by hot isostatic pressing technique [J]. J. Alloys Compd., 2018, 764: 460
doi: 10.1016/j.jallcom.2018.06.124
[31] Boehlert C J. Microstructure, creep, and tensile behavior of a Ti-12Al-38Nb (at.%) beta + orthorhombic alloy [J]. Mater. Sci. Eng., 1999, A267: 82
[32] Zhao H Z, Lu B, Tong M, et al. Tensile behavior of Ti-22Al-24Nb-0.5Mo in the range 25-650 oC [J]. Mater. Sci. Eng., 2017, A679: 455
[33] Cowen C J, Boehlert C J. Comparison of the microstructure, tensile, and creep behavior for Ti-22Al-26Nb (At. Pct) and Ti-22Al-26Nb-5B (At. Pct) [J]. Metall. Mater. Trans., 2007, 38A: 26
[34] Tang F, Nakazawa S, Hagiwara M. The effect of quaternary additions on the microstructures and mechanical properties of orthorhombic Ti2AlNb-based alloys [J]. Mater. Sci. Eng., 2002, A329-331: 492
[35] Li Y, Kan W B, Zhang Y M, et al. Microstructure, mechanical properties and strengthening mechanisms of IN738LC alloy produced by electron beam selective melting [J]. Addit. Manuf., 2021, 47: 102371
[36] Gao S L, Xu X W, Zhang H, et al. Effect of high temperature homogenization on microstructure and properties of GH4710 nickel base alloy [J]. Spec. Steel, 2024, 45(1): 87
doi: 10.20057/j.1003-8620.2022-00206
[36] 高首磊, 徐晓卫, 张 宏 等. 高温均匀化对GH4710镍基合金组织及性能的影响 [J]. 特殊钢, 2024, 45(1): 87
[37] Liu W B, Chen W, Wang T J, et al. Research progress of hot isostatic pressing technology of titanium ahoy powder [J]. Powder Metall. Ind., 2018, 28(2): 1
[37] 刘文彬, 陈 伟, 王铁军 等. 粉末钛合金的热等静压技术研究进展 [J]. 粉末冶金工业, 2018, 28(2): 1
[38] Zhao H Z, Ma X, Shi X Q, et al. Effect of rolling process on microstructure and properties of powder metallurgy Ti2AlNb alloy sheet [J]. Powder Metall. Ind., 2025, 35(5): 121
[38] 赵洪泽, 马 雄, 史晓强 等. 轧制工艺对粉末冶金Ti2AlNb合金板材组织与性能的影响 [J]. 粉末冶金工业, 2025, 35(5): 121
[39] Goyal K, Sardana N. Phase stability and microstructural evolution of Ti2AlNb alloys—A review [J]. Mater. Today: Proc., 2021, 41: 951
[40] Zhang L J, Zhang X J, Ning J. Research progress on the high-temperature creep properties of molybdenum alloy welded joints [J]. Acta Metall. Sin., 2026, 62: 47
doi: 10.11900/0412.1961.2025.00228
[40] 张林杰, 张栩菁, 宁 杰. 钼合金焊接接头高温蠕变性能研究进展 [J]. 金属学报, 2026, 62: 47
doi: 10.11900/0412.1961.2025.00228
[41] Niu J, Luo X, Tian H, et al. Vacuum brazing of aluminium metal matrix composite (55 vol.% SiCp/A356) using aluminium-based filler alloy [J]. Mater. Sci. Eng., 2012, B177: 1707
[42] Abyzov A M, Shakhov F M, Averkin A I, et al. Mechanical properties of a diamond-copper composite with high thermal conductivity [J]. Mater. Des., 2015, 87: 527
doi: 10.1016/j.matdes.2015.08.048
[43] Zhang L, Qu X H, He X B, et al. Thermo-physical and mechanical properties of high volume fraction SiCp/Cu composites prepared by pressureless infiltration [J]. Mater. Sci. Eng., 2008, A489: 285
[44] Pang X X, Xian Y J, Luo H, et al. Liquid phase flow behavior and densification mechanism of Al/B4C composites fabricated via semisolid hot isostatic pressing [J]. Rare Met. Mater. Eng., 2019, 48: 3102
[44] 庞晓轩, 鲜亚疆, 罗 昊 等. 半固态热等静压Al/B4C复合材料液相流动行为与致密化机理 [J]. 稀有金属材料与工程, 2019, 48: 3102
[45] Vidal E E, Yurko J A, Smith K. Modern beryllium extraction: A state-of-the-art Kroll reduction plant [A]. Rare Metal Technology 2015 [M]. Cham: Springer, 2015: 27
[46] Yang C, Hu R, Wang X M, et al. Effect of pre-tensile treatments on the mechanical properties and deformation mechanism of a novel Ni-based superalloy [J]. Mater. Sci. Eng., 2023, A874: 145063
[47] Zhang Y R, Liu Y C, Yu L M, et al. Microstructures and tensile properties of Ti2AlNb and Mo-modified Ti2AlNb alloys fabricated by hot isostatic pressing [J]. Mater. Sci. Eng., 2020, A776: 139043
[48] You D D, Wang Y H, Yang C, et al. Comparative analysis of the hot-isostatic-pressing densification behavior of atomized and milled Ti6Al4V powders [J]. J. Mater. Res. Technol., 2020, 9: 3091
doi: 10.1016/j.jmrt.2020.01.055
[49] Abdelhafeez A M, Essa K E A. Influences of powder compaction constitutive models on the finite element simulation of hot isostatic pressing [J]. Procedia CIRP, 2016, 55: 188
doi: 10.1016/j.procir.2016.07.025
[50] Tian W Q, Yang R Y, Cai C, et al. Discrete element analysis of rotational centrifugal method for enhanced powder packing densification in a pre-HIP capsule [J]. Particuology, 2025, 106: 99.
doi: 10.1016/j.partic.2025.09.002
[51] Abena A, Aristizabal M, Essa K. Comprehensive numerical modelling of the hot isostatic pressing of Ti-6Al-4V powder: From filling to consolidation [J]. Adv. Powder Technol., 2019, 30: 2451
doi: 10.1016/j.apt.2019.07.011
[52] Deng Y B, Kaletsch A, Broeckmann C. Simulation-based manufacturing of near-net-shape components and prediction of the microstructural evolution during hot isostatic pressing [J]. Mater. Res. Proc., 2023, 38: 120
[53] Ni R F, Zhang P J, Che L D, et al. Research on improving the simulation accuracy of HIP near-net-shape forming by coupling DEM and FEM [J]. J. Mater. Res. Technol., 2025, 36: 949
doi: 10.1016/j.jmrt.2025.03.130
[54] Tian W Q, Zhang C J, Cheng K, et al. 3D DEM-FEM coupling simulation for enhanced deformation prediction in hot isostatic pressing of a complex-shaped component [J]. J. Mater. Res. Technol., 2025, 39: 4318
doi: 10.1016/j.jmrt.2025.10.121
[55] Riehm S, Friederici V, Wieland S, et al. Tailor-made functional composite components using additive manufacturing and hot isostatic pressing [J]. Powder Metall., 2021, 64: 295
doi: 10.1080/00325899.2021.1901398
[56] Sobhani S, Albert M, Gandy D, et al. Design optimization of hot isostatic pressing capsules [J]. J. Manuf. Mater. Process., 2023, 7: 30
[57] Cai C, Zhang C J, Cai J L, et al. Sleeve step-by-step compensation design method based on hot isostatic pressing powder densification process [P]. Chin Pat, 202511626869.1, 2025
[57] 蔡 超, 张程健, 蔡基利 等. 一种基于热等静压粉末致密化进程的包套分步补偿设计方法 [P]. 中国专利, 202511626869.1, 2025)
[58] Chen H, Wei Q S, Zhang Y J, et al. Powder-spreading mechanisms in powder-bed-based additive manufacturing: Experiments and computational modeling [J]. Acta Mater., 2019, 179: 158
doi: 10.1016/j.actamat.2019.08.030
[59] Chen H, Cheng T, Li Z W, et al. Is high-speed powder spreading really unfavourable for the part quality of laser powder bed fusion additive manufacturing? [J]. Acta Mater., 2022, 231: 117901
doi: 10.1016/j.actamat.2022.117901
[60] Liu Y B, Li J K, Xu K, et al. An optimized scanning strategy to mitigate excessive heat accumulation caused by short scanning lines in laser powder bed fusion process [J]. Addit. Manuf., 2022, 60: 103256
[61] Liu Y B, Li J K, Cheng T, et al. Parameter automatic optimization strategy for laser powder bed fusion using neural network infrared radiation intensity prediction model [J]. Addit. Manuf., 2024, 92: 104373
[62] Wang S L, Zhang L C, Cai C, et al. Field-driven data processing paradigm for multi-information additive manufacturing [J]. Addit. Manuf., 2023, 61: 103352
[63] He J C, Zhang L C, Wang S L, et al. Region performance matching forming method for selective laser melting based on feature recognition of skeleton line [J]. J. Mech. Eng., 2024, 60(15): 272
[63] 何骏驰, 张李超, 王森林 等. 基于骨架线特征识别的激光选区熔化区域性能匹配成形方法 [J]. 机械工程学报, 2024, 60(15): 272
[64] Dong F, Qi J M, Xin R F. Study on high temperature mechanical properties of 304 stainless steel [J]. Hot Work Technol., 2014, 43: 96
[64] 董 方, 郄俊懋, 辛瑞峰. 304不锈钢高温力学性能研究 [J]. 热加工工艺, 2014, 43: 96
[65] Lu J H, Cao Y D, Cai J L, et al. Comparison of shape control accuracy and interfacial diffusion behavior between 304 stainless steel core and ZrO2 core in hot isostatic pressing [J]. Metall. Mater. Trans., 2025, 56A: 778
[1] 李文亚, 杨景文, 雒晓涛, 殷硕, 徐雅欣. 影响冷喷涂粒子沉积的关键因素:粉末表面氧化综述[J]. 金属学报, 2026, 62(1): 17-28.
[2] 马成勇, 侯旭儒, 赵琳, 阚成玲, 曹洋, 彭云, 田志凌. 电弧增材制造高强度Al-Mg-Sc系合金研究进展:冶金缺陷、微观组织和力学性能[J]. 金属学报, 2026, 62(1): 29-46.
[3] 刘海滨, 张迎星, 谢瑞山, 陈树君. 固相摩擦增材制造技术研究进展及其应用现状[J]. 金属学报, 2026, 62(1): 100-116.
[4] 谭若涵, 宋永锋, 陈超, 李丹, 成庶, 李雄兵. 增材制造钛合金等效弹性张量的细观力学建模与实验研究[J]. 金属学报, 2025, 61(9): 1438-1448.
[5] 杨帆, 裴世超, 罗新蕊, 陈宇翔, 李宁宇, 常永勤. 6061铝合金搅拌摩擦增材制造显微组织演变及力学性能[J]. 金属学报, 2025, 61(8): 1129-1140.
[6] 黄科, 李新志, 方学伟, 卢秉恒. 镁合金电弧熔丝增材制造技术研究现状与展望[J]. 金属学报, 2025, 61(3): 397-419.
[7] 韩启飞, 狄兴隆, 郭跃岭, 叶水俊, 郑元翾, 刘长猛. 电弧熔丝增材制造Mg/Mg双金属的组织与力学性能[J]. 金属学报, 2025, 61(2): 211-225.
[8] 尚学文, 崔潇潇, 徐磊, 卢正冠. 粉末粒度对钛合金闭式叶轮成形的影响[J]. 金属学报, 2025, 61(2): 253-264.
[9] 叶献文, 姚志浩, 王洪瑛, 王子成, 张砻耀, 董建新. 增材制造难变形高温合金GH4975的裂纹形成及其愈合机制[J]. 金属学报, 2025, 61(12): 1845-1857.
[10] 刘瑞良, 刘泉利, 李富霖. 冷喷涂后处理技术及其研究进展[J]. 金属学报, 2025, 61(10): 1449-1468.
[11] 吴文伟, 向超, 张涛, 邹志航, 孙勇飞, 刘金鹏, 张涛, 韩恩厚. 热处理工艺对选区激光熔化成型18Ni300马氏体时效钢微观组织及力学性能的影响[J]. 金属学报, 2025, 61(10): 1515-1530.
[12] 于云鹤, 谢勇, 陈鹏, 董浩凯, 侯纪新, 夏志新. 316L不锈钢表面激光熔化沉积CoCrNiCu中熵合金的界面相容性[J]. 金属学报, 2024, 60(9): 1213-1228.
[13] 张星星, LUTZ Andreas, 甘为民, MAAWAD Emad, KRIELE Armin. 退火热处理对增材制造AlSi10Mg合金宏观和微观变形行为的影响[J]. 金属学报, 2024, 60(8): 1091-1099.
[14] 刘壮壮, 丁明路, 谢建新. 金属3D打印数字化制造研究进展[J]. 金属学报, 2024, 60(5): 569-584.
[15] 黎康杰, 孙泽羽, 何蓓, 田象军. 基于熔池原位冶金的电弧增材制造Al-Cu-Li合金显微组织与硬度[J]. 金属学报, 2024, 60(5): 661-669.