Pd替代对Ti-Zr-Ni准晶合金结构的影响

金属学报

2009, Vol. 45

Issue (10): 1272-1276

论文

本期目录 | 过刊浏览

Pd替代对Ti-Zr-Ni准晶合金结构的影响

黄火根; 贾建平; 李嵘

表面物理与化学国家重点实验室; 绵阳 621907

EFFECT OF Pd SUBSTITUTION ON THE STRUCTURES OF Ti-Zr-Ni QUASICRYSTALLINE ALLOYS

HUANG Huogen; JIA Jianping; LI Rong

National Key Laboratory for Surface Physics and Chemistry; Mianyang 621907

引用本文:

黄火根贾建平李嵘. Pd替代对Ti-Zr-Ni准晶合金结构的影响[J]. 金属学报, 2009, 45(10): 1272-1276.
, . EFFECT OF Pd SUBSTITUTION ON THE STRUCTURES OF Ti-Zr-Ni QUASICRYSTALLINE ALLOYS[J]. Acta Metall Sin, 2009, 45(10): 1272-1276.

全文: PDF(899 KB)

摘要:

针对Ti₄₅Zr₃₈Ni₁₇与Ti₄₀Zr₄₀Ni₂₀准晶合金用X射线衍射仪、透射电子显微镜与金相等手段研究了不同含量的Pd替代对其结构的影响. 在吸铸态下, 前一个合金形成了二十面体准晶相(IQC)与少量配位数为8的bcc β-(Ti, Zr)相,用2%Pd (原子分数, 下同)对合金的Ti或Zr组元替代, 抑制了β-(Ti, Zr)相析出并促使配位数为14的MgZn₂结构的简单六方C14 Laves相生成. 而后一个合金中IQC相则与少量简单六方α-(Ti, Zr)共存, 在2%Pd替代后α-(Ti, Zr)消失, 生成了单一的IQC相, 但当Pd替代量增加到6.7%或13.3%时, 配位数为12的IQC相急剧减少而C14相大量析出, 并在Ti₄₀Zr_26.7Ni₂₀Pd_13.3合金中生成了单一C14相. 结果表明, 添加中等尺寸的Pd原子有利于提高 Ti-Zr-Ni合金的原子密堆性, 使合金趋于生成高配位数的Laves 相, 这种相的Fermi面与Brillouin区的相互作用不显著, 偏离了电子相的稳定机制.

关键词 ：准晶, Ti-Zr-Ni合金, Pd添加, Laves 相

Abstract：

Quasicrystals are a kind of special crystals, combining aperiodicity with long–range translational order and displaying a strong potential of applications. However, the forming law of quasicrystals, especially icosahedral, which have drawn a lot of attention since the discovery of the first quasicrystal, are not clearly known. A general knowledge, derived from the past work, is that the quasicrystal belongs to Hume–Rothery phase with special electron concentration per atom (e/a), and furthermore needs meeting the topological packing of atoms. Based on this, certain criteria named by e/a–constant line, e/a–variant line and cluster line, et al., have been used to design novel quasicrystals, especially in ternary alloy systems. But, as indicated in the previous work, these rules would not work very well in pseudo–ternary or quaternary systems built on Ti–Zr–Ni quasicrystals with the addition of Co or Cu. In order to further specify the quasicrystal formation in multi–component systems, in the present study an investigation was conducted in an alloy system, based on Ti₄₅Zr₃₈Ni₁₇ and Ti₄₀Zr₄₀Ni₂₀ alloys with the addtion of Pd, because Pd is the neighbourship of Ni in the element table like Co and Cu and has the atom size and e/a between Ti (or Zr) and Ni. Using XRD, TEM and OM, it is found that in the suction cast alloys, the icosahedral quasicrystal (IQC) phase is formed in the coexistence of a little bcc β–(Ti,Zr) in Ti₄₅Zr₃₈Ni₁₇ alloy and of a bit hexagonal α–(Ti,Zr) in Ti₄₀Zr₄₀Ni₂₀ alloy. And after 2%Pd (atomic fraction) substitution for Ti and Zr, a MgZn₂–type Laves C14 hase with coordination nuber of 14 is precipitated along with the disappearance of β–(Ti,Zr) with coordination number of 8 in the former alloy, while only a complete IQC phase with coordination number of 12 is yielded in the latter alloy. However, as the subtitution is increased up to 6.7% or 13.3% in Ti₄₀Zr₄₀Ni₂₀ alloy, the formation of IQC is prevented and the C14 phase occurs instead till a single C14 phase formin Ti₄₀Zr_26.7Ni₂₀Pd_13.3 alloy. The results show that the Pd addition in Ti–Zr–Ni allos would promte closer atom packing, being beneficial to the formation of Laves phase because of the weak interaction between Fermi surface and Brillouin zone in Hume-Rthery phase like IQC.

Key words： quasicrystal Ti-Zr-Ni alloy Pd addition Laves phase

收稿日期: 2009-03-18

ZTFLH:

TG139.7

基金资助:

中国工程物理研究院科学技术发展基金资助项目No.2007A07002

作者简介: 黄火根, 男, 1980年生, 工程师, 研究生

	服务

	把本文推荐给朋友
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	黄火根
	李嵘
44.8K

链接本文:

https://www.ams.org.cn/CN/ 或 https://www.ams.org.cn/CN/Y2009/V45/I10/1272

[1] Shechtman D, Blech I, Gratias D. Phys Rev Lett, 1984; 53: 1951
[2] Dubois J M. Mater Sci Eng, 2000; A294–296: 4
[3] Zhou G D, Guo K X. Diffraction of Crystal and Quasicrystal. Beijing: Peking University Press, 1999: 211
(周公度, 郭可信. 晶体和准晶体的衍射. 北京: 北京大学出版社, 1999: 211)
[4] Friedel J, Denoyer F. C R Acad Sci, 1987; 305B: 171
[5] Friedel J. Helv Phys Acta, 1988; 61: 538
[6] Dong C, Perrot A, Dubois J M, Belin–Ferre E. Mater Sci Forum, 1994; 150–151: 403
[7] Dong C. Quasicrystalline Materials. Beijing: National Defence Industry Press, 1998: 45
(董闯. 准晶材料. 北京: 国防工业出版社, 1998: 45)
[8] Qiang J B, Wang Y M, Wang D H, Kramer M, Thiel P, Dong C. J Non–Cryst Solids, 2004; 334: 223
[9] Huang H G. Master Degree Dissertation, Dalian University of Technology, 2005
(黄火根. 大连理工大学硕士学位论文, 2005)
[10] Dong C, Chen W R, Wang Y G, Qiang J B, Wang Q, Lei Y, Calvo–Dahlborg M, Dubois J M. J Non–Cryst Solids, 2007; 353: 3405
[11] Dong C, Wang Q, Qiang J B, Wang Y M, Jiang N, Han G, Li Y H, Wu J, Xia J H. J Phys, 2007; 40D: R273
[12] Wang L L, Huang W Q, Deng H Q, Li X F, Tang L M, Zhao L H. Rare Met Mater Eng2003; 32: 889
(王玲玲, 黄维清, 邓辉球, 李小凡, 唐黎明, 赵立华. 稀有金属材料与工程, 2003; 32: 889)
[13] Gui X C, Liao S Z, Xie H W, Zhang B W. Rare Met Mater Eng, 2006; 35: 1080
(桂许春, 廖树帜, 谢浩文, 张邦维. 稀有金属材料与工程, 2006; 35: 1080)
[14] Huang H G, Qiang J B, Jiang N, Dong C, Li T. Trans Mater Heat Treat, 2005; 26: 6
(黄火根, 羌建兵, 姜楠, 董闯, 李铁. 材料热处理学报, 2005; 26: 6)
[15] Huang H G, Qiang J B, Bai B, Dong P, Zhang P C. J Non–Cryst Solids, 2007; 353: 1670
[16] Qiang J B, Wang Q, Wang Y M, Huang H, Wu J, Dong C. Mater Sci Eng, 2007; A449: 565
[17] Qiang J B, Huang H G, Wang Q, Xia J H, Dong C. Acta Metall Sin, 2006; 42: 561
(羌建兵, 黄火根, 王清, 夏俊海, 董闯. 金属学报, 2006; 42: 561)
[18] Mayou D, Cro–Lackmann F, Laissaradiere G T, Klein T. J Non–Cryst Solids, 1993; 153–154: 412
[19] Wang Y M, Qiang J B, Wong C H, Shek C H, Dong C. J Mater Res, 2003; 18: 642
[20] Chn W, Shechtman D, Gratias D. J Mater Res, 1986; 1: 13
[21] Charles K ed., Trans. by Xiang J Z, Wu X H. Introduction to Solid State Physics. Beijing: Chemical Industry Press, 2006: 55
(Charles K著, 项金钟, 吴兴惠译. 固体物理导论. 北京: 化学工业出版社, 2006: 55)
[22] Hou Z S, Lu G X. Principles of Metallography. Shanghai: Shanghai Science and Technology Press, 1990: 59
(侯增寿, 卢光熙. 金属学原理. 上海: 上海科学技术出版社, 1990: 59)

[1]	陈永君, 白妍, 董闯, 解志文, 燕峰, 吴迪. 基于有限元分析的准晶磨料强化不锈钢表面钝化行为[J]. 金属学报, 2020, 56(6): 909-918.
[2]	秦高梧, 谢红波, 潘虎成, 任玉平. 一类介于晶体与准晶体之间的有序结构[J]. 金属学报, 2018, 54(11): 1490-1502.
[3]	樊志斌, 林小娉, 董允, 叶杰, 李婵, 李博. Mg_96.17Zn_3.15Y_0.5Zr_0.18合金高压下固溶处理时效硬化研究^*[J]. 金属学报, 2016, 52(12): 1491-1496.
[4]	陈永君, 胡小刚, 羌建兵, 董闯. 准晶磨料的“碾抹”特性对软金属表面的平整性、硬度及耐蚀性的影响^*[J]. 金属学报, 2016, 52(10): 1353-1362.
[5]	童剑黄华袁广银丁文江. 准晶增强的Mg-Zn-Al-(Y)合金热压缩变形行为[J]. 金属学报, 2011, 47(12): 1520-1526.
[6]	黄火根陈亮李嵘罗德礼. Ti₃₆Zr₄₀Ni₂₀Pd₄准晶的热稳定性与室温储氘性能[J]. 金属学报, 2010, 46(5): 629-633.
[7]	姜楠; 王清; 董闯 . Al-Cu-Ni-Fe四元体系中的准晶探讨[J]. 金属学报, 2007, 43(4): 374-378 .
[8]	羌建兵; 黄火根; 王英敏; 姜楠; 董闯 . Ti--Zr--Ni系三元准晶的成分特征研究[J]. 金属学报, 2004, 40(7): 677-682 .
[9]	邓彬彬; 郭可信 . Ag42In42Ca16二十面体准晶与２／１立方近似相Ag42In45Ca13的稳定性研究[J]. 金属学报, 2004, 40(2): 120-124 .
[10]	羌建兵; 王英敏; 袁力江 . 铸态Ti--Zr--Ni准晶基合金的室温力学性能[J]. 金属学报, 2004, 40(1): 62-66 .
[11]	雷奕; 黑祖昆; Mohique; Calvo-Dahlborg; Jean-Marie; Dubois; DONG; Chuang . Zr-二十面体准晶-十次准晶伪三元系中非晶的形成[J]. 金属学报, 2003, 39(6): 573-578 .
[12]	张瑞康; 刘静; 王建波; 汪大海; 陈方玉; 陈小梅; 桂嘉年; 王仁卉 . Al65Cu20Fe15合金的凝固组织及二十面体准晶的生成[J]. 金属学报, 1999, 35(5): 463-468 .
[13]	齐育红;张占平;黑祖昆;全明秀;董闯. Al_(65)Cu_(20)Cr_(15)准晶颗粒/铝基复合材料中二十面体准晶的扩散相变[J]. 金属学报, 1998, 34(1): 19-23.
[14]	陈立凡;陈熙琛. Al-Cu-Co-Ge十边形准晶单晶的定向生长[J]. 金属学报, 1995, 31(1): 1-6.
[15]	关绍康;汤亚力;沈宁福;胡汉起. 快速凝固Al─Fe基合金条带中准晶相的形成及稳定性[J]. 金属学报, 1994, 30(4): 150-154.

Viewed

Full text

Abstract

Cited

Shared

Discussed