金属学报  2011, Vol. 47 Issue (2): 185-190    DOI: 10.3724/SP.J.1037.2010.00427

论文 本期目录 | 过刊浏览 |

低频电磁铸造Al-4.5%Cu合金微观偏析研究

陈丹丹, 张海涛, 王向杰, 崔建忠

东北大学材料电磁过程研究教育部重点实验室, 沈阳 110819

INVESTIGATION ON MICROSEGREGATION OF Al-4.5%Cu ALLOY PRODUCED BY LOW FREQUENCY ELECTROMAGNETIC CASTING

CHEN Dandan, ZHANG Haitao, WANG Xiangjie, CUI Jianzhong

Key Laboratory of Electromagnetic Processing of Materials (Ministry of Education), Northeastern University, Shenyang 110819

陈丹丹 张海涛 王向杰 崔建忠. 低频电磁铸造Al-4.5%Cu合金微观偏析研究[J]. 金属学报, 2011, 47(2): 185-190.
, , , . INVESTIGATION ON MICROSEGREGATION OF Al-4.5%Cu ALLOY PRODUCED BY LOW FREQUENCY ELECTROMAGNETIC CASTING[J]. Acta Metall Sin, 2011, 47(2): 185-190.

摘要 参考文献 相关文章 Metrics 全文: PDF(1034 KB)   摘要: 利用直接水冷半连续(常规DC)铸造工艺和低频电磁铸造(LFEC)工艺分别制备了Al-4.5%Cu(质量分数)合金铸锭. 测量了常规DC铸造和LFEC过程中的温度曲线, 研究了低频电磁场条件下的铸锭微观组织变化和Cu元素的微观偏析. 通过金相观察发现, 在低频电磁场作用下, α-Al和$\theta$相的共晶组织变得细小, 其面积分数明显减小. 利用电子探针测量结果绘制Cu元素成分曲线, 发现在凝固的最初过渡区, Cu元素的成分曲线在低频电磁场作用下升高, α-Al中Cu元素含量增加. 通过计算得到Cu元素的有效分配系数ke, 发现在最初过渡区ke线性增大到1. LFEC工艺使得Cu元素的ke变大, 并且随着电流强度的增强这一趋势愈发明显. 由于低频电磁场加速了凝固前沿的冷却速度, 使更多的Cu原子固溶在 α-Al中, Cu元素在铸锭中的微观偏析得到了改善. 关键词 ： Al-4.5%Cu合金,  低频电磁铸造(LFEC),  微观偏析,  有效分配系数     Abstract：Microsegregation caused by the redistribution of alloying elements means the inhomogeneity of the chemical composition on the scale of a single grain. To decrease the degree of microsegregation is beneficial to avoiding ingots hot crack and shortening the homogenizing treatment time. In this study, the microsegregation of Cu element in the Al-4.5%Cu (mass fraction) alloy was investigated. Al-4.5%Cu ingots with diameter of 200 mm were prepared by the processes of conventional direct chill (DC) casting and low frequency electromagnetic casting (LFEC), respectively. The temperatures were measured during solidification processes. The effects of low frequency electromagnetic field on the microstructures and microsegregation of Cu element were investigated from eutectic analysis and electro probe microanalysis (EPMA). By the OM observations, it was found that the area fraction and dimensions of eutectic decreased markedly. The concentration profiles of Cu element were obtained with EPMA results, which showed that the profiles increased (i.e. the content of Cu element in α-Al phase increased) in the initial transit region due to the effect of low frequency electromagnetic field. The effective distribution coefficient ke of Cu element was calculated. In the initial transit region, ke increased to unit linearly. At the same time, the low frequency electromagnetic field made ke a bigger value, and the value increased with the increasing of the current intensity. Because the cooling rate at the solidification front was promoted by the low frequency electromagnetic field, and there was more Cu element in α-Al, the microsegregation of Cu element in the ingot was alleviated by the LFEC process. Key words： Al-4.5%Cu alloy    low frequency electromagnetic casting (LFEC)    microsegregation    effective distribution coefficient 收稿日期: 2010-08-30      ZTFLH:  TG14   基金资助: 国家重点基础研究发展计划资助项目2005CB623707 作者简介: 陈丹丹, 女, 1983年生, 博士生 服务 把本文推荐给朋友 加入引用管理器 E-mail Alert RSS 作者相关文章 陈丹丹 张海涛 王向杰 崔建忠 44.8K 链接本文: https://www.ams.org.cn/CN/10.3724/SP.J.1037.2010.00427      或      https://www.ams.org.cn/CN/Y2011/V47/I2/185 [1] Tong X, Beckermann C. J Cryst Growth, 1998; 187: 289 [2] Voller V R. Int J Heat Mass Transfer, 2000; 43: 2047 [3] Voller V R, Beckermann C. Metall Mater Trans, 1999; 30A: 2183 [4] Yan X Y, Xie F Y, Chu M, Chang Y A. Mater Sci Eng, 2001; A302: 268 [5] Yan X Y, Chen S, Xie F Y, Chang Y A. Acta Mater, 2002; 50: 2199 [6] Du Q, Eskin D G, Jacot A, Katgerma L. Acta Mater, 2007; 55: 1523 [7] Koch C C. Mater Sci Eng, 2000; A287: 213 [8] Yu J B, Ren Z M, Ren W L, Deng K, Zhong Y B. Acta Metall Sin (Engl Lett), 2009; 22: 191 [9] Dong J, Cui J Z, Yu F X, Ban C Y, Zhao Z H. Metall Mater Trans, 2004; 35A: 2487 [10] Zhang H T, Nagaumi H, Zuo Y B, Cui J Z. Mater Sci Eng, 2007; A448: 189 [11] Zuo Y B, Nagaumi H, Cui J Z. J Mater Process Technol, 2008; 197: 109 [12] ESKIN D G. Physical Metallurgy of Direct Chill Casting of Aluminum Alloys. London: CRC Press, 2008: 12 [13] Turchin A N, Eskin D G, Katgerman L. Metall Mater Trans, 2007; 38A: 1317 [14] Diepers H J, Beckermann C, Steinbach I. Acta Mater, 1999; 47: 3663 [15] Stefanescu D M. Science and Engineering of Casting Solidification. New York: Springer Science+Business Media, 2008: 39 [1] 刘杨,王磊,宋秀,梁涛沙. DD407/IN718高温合金异质焊接接头的组织及高温变形行为[J]. 金属学报, 2019, 55(9): 1221-1230. [2] 钟华,李传军,王江,任忠鸣,钟云波,玄伟东. 强磁场对定向凝固Al-4.5Cu合金微观偏析的影响*[J]. 金属学报, 2016, 52(5): 575-582. [3] 闫二虎,孙立贤,徐芬,徐达鸣. 基于Thermo-Calc和微观偏析统一模型对Al-6.32Cu-25.13Mg合金凝固路径的预测*[J]. 金属学报, 2016, 52(5): 632-640. [4] 钟华, 任忠鸣, 李传军, 钟云波, 玄伟东, 王秋良. 强磁场对Al-4.5Cu合金定向凝固过程中织构和晶界的影响[J]. 金属学报, 2015, 51(4): 473-482. [5] 窦坤, 卿家胜, 王雷, 张晓峰, 王宝, 刘青, 董洪标. 基于微观偏析模型的连铸方坯内裂纹敏感性研究[J]. 金属学报, 2014, 50(12): 1505-1512. [6] 赵光伟 李新中 徐达鸣 傅恒志 杜勇 贺跃辉. 三元合金单相凝固路径的统一解析模型[J]. 金属学报, 2011, 47(9): 1135-1140. [7] 王刚 郑卓 常立涛 徐磊 崔玉友 杨锐. TiAl预合金粉末的表征和后续致密化显微组织特点[J]. 金属学报, 2011, 47(10): 1263-1269. [8] 杨初斌 刘林 赵新宝 刘刚 张军 傅恒志. <001>和<011>取向DD407单晶高温合金枝晶间距和微观偏析[J]. 金属学报, 2011, 47(10): 1246-1250. [9] 甘春雷 刘雪峰 黄海友 谢建新. BFe10-1-1合金管材连续定向凝固制备工艺及组织力学性能[J]. 金属学报, 2010, 46(12): 1549-1556. [10] 蔡兆镇 朱苗勇 . 钢凝固两相区溶质元素的微观偏析及其对连铸坯表面纵裂纹的影响[J]. 金属学报, 2009, 45(8): 949-955. [11] 赵光伟 徐达鸣 宋梦华 傅恒志 杜勇 贺跃辉. 基于微观偏析统一模型及Thermo--Calc的三元合金凝固路径耦合计算[J]. 金属学报, 2009, 45(8): 956-963. [12] 黄太文 刘林 张卫国 张军 傅恒志. 抽拉速率跃迁对定向凝固单晶高温合金DD3一次枝晶间距和微观偏析的影响[J]. 金属学报, 2009, 45(10): 1225-1231. [13] 张会全; 郑少波; 郑庆; 刘自立; 蒋国昌 . 钢液凝固过程中微观偏析和钛氧夹杂生成的耦合模型[J]. 金属学报, 2006, 42(7): 745-750 . [14] 李喜; 任忠鸣; 孙延辉; 王俊; 余建波; 任维丽 . 纵向强磁场对定向凝固Al-4.5%Cu合金显微组织的影响[J]. 金属学报, 2006, 42(2): 147-152 . [15] 陈福义; 介万奇 . Al--Cu--Zn合金微观偏析的实验和Scheil模型研究[J]. 金属学报, 2004, 40(6): 664-. Viewed Full text Abstract Cited   Shared      Discussed