Please wait a minute...
Acta Metall Sin  2021, Vol. 57 Issue (6): 736-748    DOI: 10.11900/0412.1961.2020.00331
Research paper Current Issue | Archive | Adv Search |
Effect of High Temperature Ageing on Microstructure and Stress-Relief Cracking Susceptibility of Coarse Grain Heat Affected Zone in T23 steel
WANG Xue1,2(), LI Yong2,3, WANG Jiaqing3, HU Lei1
1.Key Laboratory of Green Fabrication and Surface Technology of Advanced Metal Materials, Ministry of Education, Anhui University of Technology, Ma'anshan 243032, China
2.School of Power and Mechanics, Wuhan University, Wuhan 430072, China
3.Da Tang Boiler Pressure Vessel Inspection Center Co. , Ltd. , Hefei 230088, China
Cite this article: 

WANG Xue, LI Yong, WANG Jiaqing, HU Lei. Effect of High Temperature Ageing on Microstructure and Stress-Relief Cracking Susceptibility of Coarse Grain Heat Affected Zone in T23 steel. Acta Metall Sin, 2021, 57(6): 736-748.

Download:  HTML  PDF(29869KB) 
Export:  BibTeX | EndNote (RIS)      
Abstract  

Owing to its high creep rupture strength, good weldability, and low costs, T23 steel is an ideal material for manufacturing the heating components of water walls, superheaters and reheaters in ultra-super critical plants. However, its coarse grain heat affected zone (CGHAZ) is prone to stress-relief cracking (SRC) during post-weld heat treatment or high-temperature service. The mechanism of SRC is controversial and an effective method for forecasting and preventing SRC in T23 components is currently lacking. Clarifying the mechanism of SRC in the CGHAZ of T23 steel, and developing a practical engineering technique for predicting and preventing SRC generation, are therefore essential. In this work, CGHAZ specimens of T23 steel were simulated in a thermo-mechanical simulator, and aged at 650oC for 0-48 h. After simulating the microstructure evolution of the as-welded CGHAZ during service, the SRC susceptibility of the CGHAZ was evaluated. The microstructural changes and carbide precipitation were observed by OM, SEM, TEM, and EDS. The as-welded CGHAZ of T23 steel was composed of mixed martensite and bainite with high hardness. After ageing at 650oC, the structure recovered and recrystallized with a lower dislocation density and larger sub-grains than the as-welded CGHAZ. Carbides such as M23C6, M7C3, and MX gradually precipitated inside the grains and grain boundaries, decreasing the hardness. The SRC susceptibility was high in the as-welded CGHAZ, but decreased with increasing ageing time. When the ageing time exceeded 24 h, the sample was SRC-resistant. The main cause of SRC in the CGHAZ was precipitation and growth of M23C6 on the grain boundaries, which induced the formation of softened zones in the matrix near the grain boundary, and promoted the formation of micro-voids. During ageing, the unstable microstructure in the as-welded CGHAZ transformed as carbides precipitated and the matrix recrystallized, thereby reducing the intragranular strength. Meanwhile, the depletion of alloy elements near the grain boundary was eliminated. The microstructural evolution decreased the difference between the intragranular and intergranular strengths in the CGHAZ. Finally, the CGHAZ showed significantly improved ductility and low SRC susceptibility. The hardness of the aged CGHAZ was positively related to the SRC susceptibility. At hardnesses above 250 HB, the CGHAZ was SRC-susceptible, but at hardnesses below 250 HB, the CGHAZ was SRC-resistant.

Key words:  T23 steel      coarse grain heat affected-zone      ageing      stress-relief cracking     
Received:  27 August 2020     
ZTFLH:  TG404  
Fund: National Natural Science Foundation of China(51574181);Sichuan Science and Technology Program(2018JY0668)
About author:  WANG Xue, professor, Tel: 13554693820, E-mail: wangxue2011@whu.edu.cn

URL: 

https://www.ams.org.cn/EN/10.11900/0412.1961.2020.00331     OR     https://www.ams.org.cn/EN/Y2021/V57/I6/736

Fig.1  Schematic illustration of the sample (unit: mm) for stress-relief cracking susceptibility evaluation (a) and thermal cycle curves (b) (tp/8—cooling time from peak temperature to 800oC, t8/5—cooling time from 800oC to 500oC, t5/3—cooling time from 500oC to 300oC)
Fig.2  OM images of coarse grain heat affected zone (CGHAZ) in T23 steel samples in as-welded condition (a), aged at 650oC for 6 h (b), 24 h (c), and 48 h (d)
Fig.3  SEM images of CGHAZ in T23 steel samples in as-welded condition (a), aged at 650oC for 6 h (b), 24 h (c), and 48 h (d) (M-A—martensite-austenite)
Fig.4  TEM images of CGHAZ in T23 steel samples as aged at 650oC for 6 h (a, b), 24 h (c, d), and 48 h (e, f) (Insets show the corresponding EDS results of the carbides in the circles)
Fig.5  Hardnesses of CGHAZ in T23 steel samples in as-welded condition and aged at 650oC for different time
Fig.6  Reduction of area vs test temperature of CGHAZ in T23 steel samples
Fig.7  Fracture surfaces at 750oC of CGHAZ in T23 steel samples in as-welded condition (a), aged at 650oC for 6 h (b), 24 h (c), and 48 h (d) (Insets in Figs.7a and d are corresponding high magnified images of fracture surface)
Fig.8  Longitudinal section views of CGHAZ in T23 steel samples fractured at 750oC (Insets in Figs.8b and d show the high magnified images of grain boundaries with void)
Fig.9  TEM images of CGHAZ in T23 steel samples fractured at 750oC
Fig.10  TEM image (a) and typical EDS line scans (b) done across prior austenite grain boundaries in fracture samples of as-welded CGHAZ of T23 steel sample tested at 750oC
Fig.11  TEM image (a) and typical EDS line scans (b) done across prior austenite grain boundaries in fracture samples of CGHAZ of T23 steel aged at 650oC for 48 h tested at 750oC
Fig.12  Illustration of fracture mechanism of as-welded (a) and aged (b) CGHAZ (PAGB—prior austenite grain boundary)
T / oC6 h24 h48 h
55061124444889
50096593863577269
Table 1  Equivalent heat exposure conditions of CGHAZs of T23 steels aged at 650oC for different time
1 Bendick W, Gabrel J, Hahn B, et al. New low alloy heat resistant ferritic steels T/P23 and T/P24 for power plant application [J]. Int. J. Pressure Vessels Pip., 2007, 84: 13
2 Arndt J, Haarmann K, Kottmann G, et al. The T23/T24 Book-New Grades for Waterwalls and Superheaters [M]. Vallourec & Mannesmann Tubes, 1998: 24
3 Igarashi M, Yoshizawa M, Matsuo H, et al. Long-term creep properties of low C-2.25Cr-1.6W-V-Nb steel (T23/P23) for fossil fired and heat recovery boilers [J]. Mater. Sci. Eng., 2009, A510-511: 104
4 Kucharova K, Sklenicka V, Kvapilova M, et al. Creep and microstructural processes in a low-alloy 2.25%Cr1.6%W steel (ASTM Grade 23) [J]. Mater. Charact., 2015, 109: 1
5 Vaillant J C, Vandenberghe B, Hahn B, et al. T/P23, 24, 911 and 92: New grades for advanced coal-fired power plants—Properties and experience [J]. Int. J. Pressure Vessels Pip., 2008, 85: 38
6 Yang F, Zhang Y L, Ren Y N, et al. Welding of New Type Heat-resistant Steels [M]. Beijing: China Electric Power Press, 2006: 79
杨 富, 章应霖, 任永宁等. 新型耐热钢焊接 [M]. 北京: 中国电力出版社, 2006: 79
7 Wang X, Xu D L, Chen Y C, et al. The reheat cracking susceptibility of T23 (7CrWVMoNb9-6) steel [J]. Mater. Sci. Technol., 2009, 17(): 172
王 学, 徐德录, 陈玉成等. T23钢再热裂纹敏感性 [J]. 材料科学与工艺, 2009, 17(): 172
8 Zhang B, Gao Z Y, Wang D T, et al. Tests studies on HCM2S steel's susceptibility to reheat cracking [J]. J. Power Eng., 2006, 26: 300
张 波, 高子瑜, 王德泰等. HCM2S钢再热裂纹敏感性的试验研究 [J]. 动力工程, 2006, 26: 300
9 Dhooge A, Vekeman J. New generation 21/4Cr steels T/P 23 and T/P 24 weldability and high temperature properties [J]. Weld. World, 2005, 49: 75
10 Nawrocki J G, Dupont J N, Robino C V, et al. The stress-relief cracking susceptibility of a new ferritic steel—Part 1: Single-pass heat-affected zone simulations [J]. Weld. J., 2000, 79: 355s
11 Long H G, Long Y, Chen H D. Mechanism of T23/12Cr1MoV dissimilar steel welding failure in high temperature reheater [J]. Electr. Power, 2011, 44(5): 70
龙会国, 龙 毅, 陈红冬. 高温再热器T23/12Cr1MoV异种钢焊缝失效机理 [J]. 中国电力, 2011, 44(5): 70
12 Hippsley C A, Knott J F, Edwards B C. A study of stress relief cracking in 214Cr 1 Mo steel—I. The effects of P segregation [J]. Acta Metall., 1980, 28: 869
13 Shin J, McMahon C J. Mechanisms of stress relief cracking in a ferritic steel[J]. Acta Metall., 1984, 32: 1535
14 Kanazawa S, Yamato K, Takeda T, et al. Study of reheat cracking in weldment (report 2): Relation between cracking susceptibility and some properties of HAZ at high temperature [J]. Trans. Jpn. Weld. Soc., 1977, 8: 119
15 Magula V, Grman D, Patscheider J. Segregation of impurities on grain boundaries in tests of resistance to “reheat and underclad” cracking [J]. Scr. Mater., 1997, 37: 1811
16 Tamaki K, Suzuki J, Tajiri M. Effect of Vanadium and Titanium on reheat cracking sensitivity: Study of reheat cracking of Cr-Mo steels (report 4) [J]. Trans. Jpn. Weld. Soc., 1984, 15: 17
17 Ito Y, Nakanishi M. Study on stress relief cracking in welded low alloy steels (report 1): The investigation of the condition under which stress relief cracking may occur [J]. J. Jpn. Weld. Soc., 1971, 40: 1261
18 Balaguer J P, Wang Z, Nippes E F. Stress-relief cracking of a copper-containing HSLA steel [J]. Weld. J., 1989, 68: 121s
19 Ito Y, Nakanishi M. Study on stress relief cracking in welded low alloy steels (report 2): The investigation of stress relief cracking susceptibility on low alloy steels [J]. J Jpn. Weld. Soc., 1972, 41: 59
20 Nawrocki J G, Dupont J N, Robino C V, et al. The mechanism of stress-relief cracking in a ferritic alloy steel [J]. Weld. J., 2003, 82(2): 25s
21 Li Y, Wang X, Wang J Q, et al. Stress-relief cracking mechanism in simulated coarse-grained heat-affected zone of T23 steel [J]. J. Mater. Process. Technol., 2019, 266: 73
22 Pilling J, Ridley N. Tempering of 2.25 Pct Cr-1 Pct Mo low carbon steels [J]. Metall. Trans., 1982, 13A: 557
23 Yu Z S, Nie M, Hou S F, et al. The carbide contained in HCM2S (T23) steel and evolution regularity thereof [J]. Therm. Power Gener., 2012, 41(9): 1
于在松, 聂 铭, 侯淑芳等. HCM2S(T23)钢中的碳化物及其演化规律 [J]. 热力发电, 2012, 41(9): 1
24 Zieliński A, Golański G, Sroka M, et al. Microstructure and mechanical properties of the T23 steel after long-term ageing at elevated temperature [J]. Mater. High Temp., 2016, 33: 154
25 Miyata K, Igarashi M, Sawaragi Y. Effect of trace elements on creep properties of 0.06C-2.25Cr-1.6W-0.1Mo-0.25V-0.05Nb steel [J]. ISIJ Int., 1999, 39: 947
26 Morito S, Yoshida H, Maki T, et al. Effect of block size on the strength of lath martensite in low carbon steels [J]. Mater. Sci. Eng., 2006, A438-440: 237
27 Anderson T L. Fracture Mechanics: Fundamentals and Applications [M]. 4th Ed., New York: CRC Press, 2017: 233
28 Cane B J, Middleton C J. Intergranular creep-cavity formation in low-alloy bainitic steels [J]. Met. Sci., 1981, 15: 295
29 Qian Z P. Deformation and Fracture of Materials [M]. Shanghai: Tongji University Press, 1989: 139
钱志屏. 材料的变形与断裂 [M]. 上海: 同济大学出版社, 1989: 139
30 Yin Y F, Faulkner R G. Model predictions of grain boundary chromium depletion in Inconel 690 [J]. Corros. Sci., 2007, 49: 2177
31 Chen B, Hao X C, Ma Y C, et al. Effects of nitrogen addition on microstructure and grain boundary microchemistry of Inconel alloy 690 [J]. Acta Metall. Sin., 2017, 53: 983
陈 波, 郝宪朝, 马颖澈等. 添加N对Inconel 690合金显微组织和晶界微区成分的影响 [J]. 金属学报, 2017, 53: 983
32 Wang X, Li X Q, Yang C, et al. Aging properties of T23 weld joint in water wall of USC boilers [J]. J. Chin. Soc. Power Eng., 2015, 35: 325
王 学, 李夕强, 杨 超等. 超超临界锅炉水冷壁T23接头时效性能 [J]. 动力工程学报, 2015, 35: 325
33 Mohyla P, Foldyna V. Improvement of reliability and creep resistance in advanced low-alloy steels [J]. Mater. Sci. Eng., 2009, A510-511: 234
[1] YE Junjie, HE Zhirong, ZHANG Kungang, DU Yuqing. Effect of Ageing on Microsturcture, Tensile Properties, and Shape Memory Behaviors of Ti-50.8Ni-0.1Zr Shape Memory Alloy[J]. 金属学报, 2021, 57(6): 717-724.
[2] LIU Chao, YAO Zhihao, GUO Jing, PENG Zichao, JIANG He, DONG Jianxin. Microstructure Evolution Behavior of Powder Superalloy FGH4720Li at Near Service Temperature[J]. 金属学报, 2021, 57(12): 1549-1558.
[3] GUO Qianying, LI Yanmo, CHEN Bin, DING Ran, YU Liming, LIU Yongchang. Effect of High-Temperature Ageing on Microstructure and Creep Properties of S31042 Heat-Resistant Steel[J]. 金属学报, 2021, 57(1): 82-94.
[4] LI Jichen, FENG Di, XIA Weisheng, LIN Gaoyong, ZHANG Xinming, REN Minwen. Effect of Non-Isothermal Ageing on Microstructure and Properties of 7B50 Aluminum Alloy[J]. 金属学报, 2020, 56(9): 1255-1264.
[5] PENG Yanyan, YU Liming, LIU Yongchang, MA Zongqing, LIU Chenxi, LI Chong, LI Huijun. Effect of Ageing Treatment at 650 ℃ on Microstructure and Properties of 9Cr-ODS Steel[J]. 金属学报, 2020, 56(8): 1075-1083.
[6] ZHU Liang, GUO Mingxing, YUAN Bo, ZHUANG Linzhong, ZHANG Jishan. Effect of Ageing Routes on Precipitation Behaviors of Al-0.7Mg-0.5Si-0.2Cu-0.5Zn Alloy[J]. 金属学报, 2020, 56(7): 997-1006.
[7] GENG Yaoxiang, FAN Shimin, JIAN Jianglin, XU Shu, ZHANG Zhijie, JU Hongbo, YU Lihua, XU Junhua. Mechanical Properties of AlSiMg Alloy Specifically Designed for Selective Laser Melting[J]. 金属学报, 2020, 56(6): 821-830.
[8] LIANG Mengchao, CHEN Liang, ZHAO Guoqun. Effects of Artificial Ageing on Mechanical Properties and Precipitation of 2A12 Al Sheet[J]. 金属学报, 2020, 56(5): 736-744.
[9] LI Jichen, FENG Di, XIA Weisheng, GUO Weimin, WANG Guoying. The Non-Isothermal Double Ageing Behaviour of 7055 Aluminum Alloy[J]. 金属学报, 2020, 56(11): 1495-1506.
[10] Hailong QIN,Ruiyao ZHANG,Zhongnan BI,Lee Tung Lik,Hongbiao DONG,Jinhui DU,Ji ZHANG. Study on the Evolution of Residual Stress During Ageing Treatment in a GH4169 Alloy Disk[J]. 金属学报, 2019, 55(8): 997-1007.
[11] Chao CAI,Yang LI,Jinfeng LI,Zhao ZHANG,Jianqing ZHANG. Correlation Between Ageing Precipitation, Potential and Intergranular Corrosion of 2A97 Al-Li Alloy Sheet[J]. 金属学报, 2019, 55(8): 958-966.
[12] Xiaodong LIN,Qunjia PENG,En-Hou HAN,Wei KE. Effect of Annealing on Microstructure of Thermally Aged 308L Stainless Steel Weld Metal[J]. 金属学报, 2019, 55(5): 555-565.
[13] ZHU Shang,LI Zhihui,YAN Lizhen,LI Xiwu,ZHANG Yongan,XIONG Baiqing. Effects of Zn Addition on the Natural Ageing Behavior and Bake Hardening Response of a Pre-Aged Al-Mg-Si-Cu Alloy[J]. 金属学报, 2019, 55(11): 1395-1406.
[14] Xuemei XIANG, Yuxiang LAI, Chunhui LIU, Jianghua CHEN. Sn-Induced Modification of the Precipitation Pathways upon High-Temperature Ageing in an Al-Mg-Si Alloy[J]. 金属学报, 2018, 54(9): 1273-1280.
[15] Yuanyuan SONG, Mingjiu ZHAO, Lijian RONG. Study on the Precipitation of γ' in a Fe-Ni Base Alloy During Ageing by APT[J]. 金属学报, 2018, 54(9): 1236-1244.
No Suggested Reading articles found!