金属学报  1964, Vol. 7 Issue (2): 145-156

论文 本期目录 | 过刊浏览 |

真空感应炉氧化镁坩埚熔炼纯铁的研究

吴超万;李伟立;邵象华

冶金工业部钢铁研究院;冶金工业部钢铁研究院;冶金工业部钢铁研究院

INVESTIGATION IN THE VACUUM MELTING OF HIGH-PURITY IRON IN MAGNESIA CRUCIBLES

WU CHAO-WAN; LI WEI-LI; SHAO HSIANG-HUA (Iron & Steel Research Institute; The Ministry of Metallurgical Industry)

吴超万;李伟立;邵象华. 真空感应炉氧化镁坩埚熔炼纯铁的研究[J]. 金属学报, 1964, 7(2): 145-156.
, , . INVESTIGATION IN THE VACUUM MELTING OF HIGH-PURITY IRON IN MAGNESIA CRUCIBLES[J]. Acta Metall Sin, 1964, 7(2): 145-156.

摘要 参考文献 相关文章 Metrics 全文: PDF(1007 KB)   摘要: 用容量为10公斤的真空感应炉研究了在电熔氧化鎂坩堝中熔炼純鉄时熔池中碳和氧的反应,以及坩堝在这个反应中所起的作用。証实在熔炼过程中坩堝不断向熔池供氧,因此熔池的含氧量在降低到最低值后重新回升。 在10~(-4)(及10~(-1))毫米汞柱的炉压下,发現熔池中的[％C]·[％O]乘积都达到6×10~(-6)至3.5×10~(-5)之間的数值。当配料含碳0.03—0.05％而含氧为其一半时,可以得到含碳0.006％以下、含氧0.003％以下的高純度铁。 坩堝对熔池的影响随着使用次数的增长而減弱。 熔池的氧浓度对最終含氮量有显著影响。含氧量越高,脫氮就越慢。 Abstract：Reaction between carbon and oxygen in melts of iron was studied, using crucibles made of electrically prefused magnesia, in a medium-frequency induction furnace of 10kg. capacity. It was found that the melts continually absorbed oxygen from the crucible, so that during the heat its oxygen content dropped to a minimum and then rose again. Under a furnace pressure of 10-4 (and in a few cases 10~(-1) mm Hg, the [％C].[0％] product fell between 6×10~(-6) and 3.5×10~(-5). By limiting the carbon content of the charged iron to 0.03—0.05％, with a C:O ratio of 2, a high-purity product containing less than 0.003％ oxygen and less than 0.006％ carbon was satisfactorily obtained. The melt-crucible reaction became less pronounced with each heat after a new crucible had been put into use. The oxygen content of the melt had a marked effect on its final nitrogen content. A high oxygen concentration retarded de-nitrogenation. 收稿日期: 1964-02-18      服务 把本文推荐给朋友 加入引用管理器 E-mail Alert RSS 作者相关文章 吴超万 李伟立 邵象华 44.8K 链接本文: https://www.ams.org.cn/CN/      或      https://www.ams.org.cn/CN/Y1964/V7/I2/145 [1] Elliott, J. F., Gleiser, M.: Thermochemistry for Steelmaking, (Addison-Wesley 1960) , vol. 1, p. 183． [2] Chipman, J.: Basic Open Hearth Steelmaking, 2nd ed., (AIME, 1951) , p. 649． [3] Wever, F., Fischer, W. A.: Engelbrecht, H.: Stahl Eisen, 1954, 1515． [4] Moore, J. H.: Metal Progr., 1953, 64, (10) , 103． [5] Fast, J. D.: Stahl Eisen, 1953, 1484． [6] Kothemann, K. H., Treppschuh, H., Fischer, W. A.: Arch. Eisenhuttenw., 1956, 563． [7] Fischer, W. A., Treppschuh, H., Kothemann, K. H.: Arch. Eisenhuttenw., 1956, 567． [8] Brotzmann, K.: Arch. Eisenhuttenw., 1960, 67． [9] Bogdandy, L. V., Schmolke, R., Winzer, G.: Arch. Eisenhuttenw., 1958, 231． [10] 邹元爔:金属学报,1958,3,238． [11]#12 [12] Shiro Ban-ya, Sachio Matoba: Physical Chemistry of Process Metallurgy, ed. G. R. St. Pieerre, (Pt. 1) , (Interscience, 1961) , p, 373． [13] Fuwa, T., Chipman, J.: Trans. AIME, 1960, 218, 888． [14] Thomas, J., Moreau, L.: Rev. Met., 1946, 43, 204． [15] #12 [16]#12 [17] 渡辺哲弥:鉄鋼,1961,47,1670． [18] Machlin, E. S.: Trans. AIME, 1960, 218, 314． [19] Fischer, W. A., Hoffmann, A.: Arch. Eisenhuttenw., 1960, 411． [20] Naeser, G., Scholz, W.: Stahl Eisen, 1959, 137． [21] Naeser, G.: Stahl Eisen, 1948, 375．W No related articles found! Viewed Full text Abstract Cited   Shared      Discussed