Please wait a minute...
Acta Metall Sin  2026, Vol. 62 Issue (10): 1702-1712    DOI: 10.11900/0412.1961.2024.00445
Research paper Current Issue | Archive | Adv Search |
Effects of Powder Morphology on Microstructure Evolution and Mechanical Properties of Laser Powder Bed Fusion Degradable Zn-Mn-Mg Alloy
HUANG Chengcong1,2, LI Yageng1,2(), WANG Luning1,2()
1 Beijing Advanced Innovation Center for Materials Genome Engineering, School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083, China
2 Institute of Materials Intelligent Technology, Liaoning Academy of Materials, Shenyang 110004, China
Cite this article: 

HUANG Chengcong, LI Yageng, WANG Luning. Effects of Powder Morphology on Microstructure Evolution and Mechanical Properties of Laser Powder Bed Fusion Degradable Zn-Mn-Mg Alloy. Acta Metall Sin, 2026, 62(10): 1702-1712.

Download:  HTML  PDF(2444KB) 
Export:  BibTeX | EndNote (RIS)      
Abstract  

Zinc-based alloys are emerging as the next generation of degradable metals due to their favorable degradation rates. Additive manufacturing offers the capability to produce personalized structures, making it a promising method for generating biomedical metal components. However, during laser powder bed fusion (LPBF), zinc-based alloys can experience significant evaporation because of their low melting point, which often results in poor surface quality. Optimizing powder morphology and particle size present a potential strategy to enhance forming quality. In this study, two Zn-1Mn-0.4Mg (mass fraction, %) alloy powders with particle sizes of 15-53 μm and 30-75 μm were produced using electrode induction gas atomization (EIGA) and the plasma rotating electrode process (PREP), respectively. Bulk alloys were fabricated using LPBF, and the processing windows for both powders were compared to investigate the effects of powder morphology and particle size on the microstructural and mechanical properties. The results indicated that PREP powders, which exhibited better sphericity and larger particle size, had a broader and more stable LPBF processing window. This led to bulk samples with higher density and smaller grain sizes compared to those prepared with EIGA powders. Under the processing parameters of laser power P = 50 W and scanning rate V = 600 mm/s, both bulk sample types displayed similar tensile yield strength (~210 MPa) and ultimate tensile strength (~285 MPa). However, the compressive yield strength of the EIGA + LPBF samples ((288.2 ± 4.3) MPa) was slightly higher than that of the PREP + LPBF samples ((258.5 ± 3.5) MPa). By contrast, the PREP + LPBF samples demonstrated significantly greater tensile elongation (21.8% ± 2.3%) compared to the EIGA + LPBF samples (3.3% ± 0.7%). This enhanced ductility was primarily attributed to the more homogeneous thermal conductivity and strain distribution in PREP powders during the LPBF process.

Key words:  additive manufacturing      zinc alloy      powder characteristics      mechanical property     
Received:  28 December 2024     
ZTFLH:  TG 146.1  
Fund: National Key Research and Development Program of China(2023YFB3813000);National Na-tural Science Foundation of China(52471260);National Na-tural Science Foundation of China(52201294)
Corresponding Authors:  LI Yageng, associate professor, Tel: (010)62332609, E-mail: yagengli@ustb.edu.cn;
WANG Luning, professor, Tel: (010)62332609, E-mail: luning.wang@ustb.edu.cn

URL: 

https://www.ams.org.cn/EN/10.11900/0412.1961.2024.00445     OR     https://www.ams.org.cn/EN/Y2026/V62/I10/1702

MethodZnMnMgO
EIGA98.560.920.43< 0.1
PREP98.560.970.38< 0.1
Table 1  Chemical compositions of Zn-Mn-Mg alloy powders prepared by electrode induction gas atomization (EIGA) and plasma rotating electrode process (PREP) methods
Fig.1  SEM images (a, b) and particle size distributions (c, d) of Zn-Mn-Mg alloy powders prepared by EIGA (a, c) and PREP (b, d) methods (Dv(10), Dv(50), and Dv(90) indicate 10%, 50%, and 90% cumulative particle sizes, respectively)
Fig.2  Contour diagram of relative density (a) and OM images of laser powder bed fusion (LPBF) bulk samples prepared via EIGAed powders at P = 40 W, V = 900 mm/s (b), P = 70 W, V = 900 mm/s (c), P = 40 W, V = 800 mm/s (d), P = 80 W, V = 900 mm/s (e), P = 50 W, V = 600 mm/s (f), P = 80 W, V = 600 mm/s (g), P = 40 W, V = 500 mm/s (h), P = 50 W, V = 500 mm/s (i), P = 60 W, V = 600 mm/s (j), P = 70 W, V = 700 mm/s (k), and P = 80 W, V = 800 mm/s (l) (P—laser power, V—scanning rate)
Fig.3  Contour diagram of relative density (a) and OM images of LPBF bulk samples prepared via PREPed powders at P = 40 W, V = 900 mm/s (b), P = 70 W, V = 900 mm/s (c), P = 40 W, V = 800 mm/s (d), P = 80 W, V = 900 mm/s (e), P = 50 W, V = 600 mm/s (f), P = 80 W, V = 600 mm/s (g), P = 40 W, V = 500 mm/s (h), P = 50 W, V = 500 mm/s (i), P = 60 W, V = 600 mm/s (j), P = 70 W, V = 700 mm/s (k), and P = 80 W, V = 800 mm/s (l)
Fig.4  Low (a) and locally high (b) magnified XRD patterns of bulk samples prepared via EIGA + LPBF and PREP + LPBF at P = 50 W, V = 600 mm/s
Fig.5  OM images of bulk samples prepared via EIGA + LPBF (a) and PREP + LPBF (b) at P = 50 W, V = 600 mm/s; EPMA image (c) and corresponding element mappings of Mn (d), Mg (e), and O (f) of bulk sample prepared via PREP + LPBF of rectangle area in Fig.5c
Fig.6  Inverse pole figures (a, b), pole figures (c, d), and kernel average misorientation figures (e, f) of LPBF bulk samples prepared via EIGA + LPBF (a, c, e) and PREP + LPBF (b, d, f) at P = 50 W, V = 600 mm/s (BD—building direction)
Fig.7  Tensile (a) and compression (b) stress-strain curves of bulk samples prepared via EIGA + LPBF and PREP + LPBF at P = 50 W, V = 600 mm/s
Fig.8  Low (a, b) and high (c, d) magnified SEM images showing the tensile fracture surfaces of bulk samples prepared via EIGA + LPBF (a, c) and PREP + LPBF (b, d) at P = 50 W, V = 600 mm/s
Fig.9  Bright-field TEM images (a, b) and STEM image and corresponding EDS element mappings (c) of LPBF bulk samples prepared via PREPed powder (Inset in Fig.9a shows the SAED pattern of the rectangle area)
[1] Kabir H, Munir K, Wen C E, et al. Recent research and progress of biodegradable zinc alloys and composites for biomedical applications: Biomechanical and biocorrosion perspectives[J]. Bioact. Mater., 2021, 6: 836
doi: 10.1016/j.bioactmat.2020.09.013 pmid: 33024903
[2] Li Y G, Shi Y X, Lu Y C, et al. Additive manufacturing of vascular stents[J]. Acta Biomater., 2023, 167: 16
doi: 10.1016/j.actbio.2023.06.014 pmid: 37331614
[3] Mostaed E, Sikora-Jasinska M, Drelich J W, et al. Zinc-based alloys for degradable vascular stent applications[J]. Acta Biomater., 2018, 71: 1
doi: S1742-7061(18)30125-9 pmid: 29530821
[4] Qi X H, Liang X K, Wang J H, et al. Microstructure tailoring in laser powder bed fusion (L-PBF): Strategies, challenges, and future outlooks[J]. J. Alloys Compd., 2024, 970: 172564
doi: 10.1016/j.jallcom.2023.172564
[5] Clare A T, Mishra R S, Merklein M, et al. Alloy design and adaptation for additive manufacture[J]. J. Mater. Process. Technol., 2022, 299: 117358
doi: 10.1016/j.jmatprotec.2021.117358
[6] Bose S, Ke D X, Sahasrabudhe H, et al. Additive manufacturing of biomaterials[J]. Prog. Mater. Sci., 2018, 93: 45
doi: 10.1016/j.pmatsci.2017.08.003 pmid: 31406390
[7] Zheng Y F, Xia D D, Shen Y N, et al. Additively manufactured biodegradable metal implants[J]. Acta Metall. Sin., 2021, 57: 1499
郑玉峰, 夏丹丹, 谌雨农 等. 增材制造可降解金属医用植入物[J]. 金属学报, 2021, 57: 1499
doi: 10.11900/0412.1961.2021.00294
[8] Li Y G, Jahr H, Zhou J, et al. Additively manufactured biodegradable porous metals[J]. Acta Biomater., 2020, 115: 29
doi: S1742-7061(20)30478-5 pmid: 32853809
[9] Kassym K, Perveen A. Atomization processes of metal powders for 3D printing[J]. Mater. Today: Proc., 2020, 26: 1727
[10] Zhao X M, Chen J, Lin X, et al. Study on microstructure and mechanical properties of laser rapid forming Inconel 718[J]. Mater. Sci. Eng., 2008, A478: 119
[11] Tammas-Williams S, Withers P J, Todd I, et al. Porosity regrowth during heat treatment of hot isostatically pressed additively manufactured titanium components[J]. Scr. Mater., 2016, 122: 72
doi: 10.1016/j.scriptamat.2016.05.002
[12] Spierings A B, Herres N, Levy G. Influence of the particle size distribution on surface quality and mechanical properties in AM steel parts[J]. Rapid Prototyping J., 2011, 17: 195
doi: 10.1108/13552541111124770
[13] Abd-Elghany K, Bourell D L. Property evaluation of 304L stainless steel fabricated by selective laser melting[J]. Rapid Prototyping J., 2012, 18: 420
doi: 10.1108/13552541211250418
[14] Baitimerov R, Lykov P, Zherebtsov D, et al. Influence of powder characteristics on processability of AlSi12 alloy fabricated by selective laser melting[J]. Materials, 2018, 11: 742
doi: 10.3390/ma11050742
[15] Bi Z N, Zhang P, Zhang H P. Effect of metal powder characteristics on metallurgical quality of laser powder bed fusion additive manufacturing[J]. Powder Metall. Ind., 2024, 34(6): 1
毕中南, 张 鹏, 张浩鹏. 金属粉末特征对激光粉末床熔融成形质量的影响[J]. 粉末冶金工业, 2024, 34(6): 1
[16] Qin F, Shi Q, Zhou G, et al. Influence of powder particle size distribution on microstructure and mechanical properties of 17-4 PH stainless steel fabricated by selective laser melting[J]. J. Mater. Res. Technol., 2023, 25: 231
doi: 10.1016/j.jmrt.2023.05.241
[17] Shi Z Z, Yu J, Liu X F. Microalloyed Zn-Mn alloys: From extremely brittle to extraordinarily ductile at room temperature[J]. Mater. Des., 2018, 144: 343
doi: 10.1016/j.matdes.2018.02.049
[18] Zhu X L, Ren T T, Guo P S, et al. Strengthening mechanism and biocompatibility of degradable Zn-Mn alloy with different Mn content[J]. Mater. Today Commun., 2022, 31: 103639
[19] Zheng Y Z, Huang C C, Li Y G, et al. Mimicking the mechanical properties of cortical bone with an additively manufactured biodegradable Zn-3Mg alloy[J]. Acta Biomater., 2024, 182: 139
doi: 10.1016/j.actbio.2024.05.023
[20] Li Z L, Zhang X L, Tian D K. Effect of multi-pass compression deformation on microstructure evolution of AZ80 magnesium alloy[J]. Acta Metall. Sin., 2024, 60: 311
doi: 10.11900/0412.1961.2022.00010
李振亮, 张欣磊, 田董扩. 多道次压缩变形对AZ80镁合金微观组织演化的影响[J]. 金属学报, 2024, 60: 311
doi: 10.11900/0412.1961.2022.00010
[21] Sangid M D, Ezaz T, Sehitoglu H. Energetics of residual dislocations associated with slip-twin and slip-GBs interactions[J]. Mater. Sci. Eng., 2012, A542: 21
[22] Chu F Z, Shen H P, Liu J W, et al. Improved ductility by reducing powder size in laser powder bed fusion of AlSi10Mg[J]. Addit. Manuf. Front., 2024, 3: 200122
[23] Zhang S S, Lane B, Whiting J, et al. On thermal properties of metallic powder in laser powder bed fusion additive manufacturing[J]. J. Manuf. Process., 2019, 47: 382
doi: 10.1016/j.jmapro.2019.09.012
[24] Gusarov A V, Yadroitsev I, Bertrand P, et al. Model of radiation and heat transfer in laser-powder interaction zone at selective laser melting[J]. J. Heat Transfer., 2009, 131: 072101
[25] Körner C, Attar E, Heinl P. Mesoscopic simulation of selective beam melting processes[J]. J. Mater. Process. Technol., 2011, 211: 978
doi: 10.1016/j.jmatprotec.2010.12.016
[26] Hosseini E, Popovich V A. A review of mechanical properties of additively manufactured Inconel 718[J]. Addit. Manuf., 2019, 30: 100877
[27] Farzadfar S A, Murtagh M J, Venugopal N. Impact of IN718 bimodal powder size distribution on the performance and productivity of laser powder bed fusion additive manufacturing process[J]. Powder Technol., 2020, 375: 60
doi: 10.1016/j.powtec.2020.07.092
[28] Coe H G, Pasebani S. Use of bimodal particle size distribution in selective laser melting of 316L stainless steel[J]. J. Manuf. Mater. Process., 2020, 4: 8
doi: 10.3390/jmmp4010008
[29] Qin Y, Liu J G, Chen Y Z, et al. Influence of laser energy input and shielding gas flow on evaporation fume during laser powder bed fusion of Zn metal[J]. Materials, 2021, 14: 2677
doi: 10.3390/ma14102677
[30] Ruan G, Liu C, Qu H Q, et al. A comparative study on laser powder bed fusion of IN718 powders produced by gas atomization and plasma rotating electrode process[J]. Mater. Sci. Eng., 2022, A850: 143589
[31] Brika S E, Letenneur M, Dion C A, et al. Influence of particle morphology and size distribution on the powder flowability and laser powder bed fusion manufacturability of Ti-6Al-4V alloy[J]. Addit. Manuf., 2020, 31: 100929
[32] Venezuela J, Dargusch M S. The influence of alloying and fabrication techniques on the mechanical properties, biodegradability and biocompatibility of zinc: A comprehensive review[J]. Acta Biomater., 2019, 87: 1
doi: S1742-7061(19)30055-8 pmid: 30660777
[33] Wu Y, Fu Q Y, Guo B S, et al. Revealing the mechanical and degradation properties of the Zn-Cu-Ti alloy with ununiform heterostructure[J]. Mater. Sci. Eng., 2022, A853: 143775
[34] Shi Z Z, Li X M, Yao S L, et al. 300 MPa grade biodegradable high-strength ductile low-alloy (BHSDLA) Zn-Mn-Mg alloys: An in vitro study[J]. J. Mater. Sci. Technol., 2023, 138: 233
doi: 10.1016/j.jmst.2022.08.015
[35] Yin D D, Boehlert C J, Long L J, et al. Tension-compression asymmetry and the underlying slip/twinning activity in extruded Mg-Y sheets[J]. Int. J. Plast., 2021, 136: 102878
doi: 10.1016/j.ijplas.2020.102878
[36] Long F, Kacher J, Yao Z W, et al. A tomographic TEM study of tension-compression asymmetry response of pyramidal dislocations in a deformed Zr-2.5Nb alloy[J]. Scr. Mater., 2018, 153: 94
doi: 10.1016/j.scriptamat.2018.04.043
[37] Chen C, Huang H, Niu J L, et al. Origin of high tension-compression yield asymmetry in as-extruded pure zinc[J]. Scr. Mater., 2021, 200: 113922
doi: 10.1016/j.scriptamat.2021.113922
[38] Chandra S, Wang C C, Tor S B, et al. Powder-size driven facile microstructure control in powder-fusion metal additive manufacturing processes[J]. Nat. Commun., 2024, 15: 3094
doi: 10.1038/s41467-024-47257-w
[1] LI Shuaiyu, LIU Zedong, YANG Jieren, JIN Wei, PENG Bo, DU Xin, ZHOU Siman. Microstructural Inheritance Behavior and Mechanical Property Control of TA18 Alloy From Ingot to Tube Blank[J]. 金属学报, 2026, 62(9): 1487-1502.
[2] LIU Zetian, LU Weizhao, XU Xinyu, LIU Xu, ZHANG Shaoyou, WANG Huiyuan. Effect of Homogenization Temperature on the Microstructure and Mechanical Properties of 3003 Aluminum Alloys[J]. 金属学报, 2026, 62(9): 1503-1516.
[3] GUO Chuanping, SHI Chenchen, LIU Peng, GAO Dongfang, ZHAO Yangyang, QIAO Yang. Prediction of Mechanical Properties of Biodegradable Zinc Alloys Based on Machine Learning[J]. 金属学报, 2026, 62(9): 1615-1626.
[4] ZHANG Xue, LIANG Jingjing, ZHAO Yusong, ZHANG Huan, MU Yahang, ZHOU Yizhou, SUN Xiaofeng, LI Jinguo. Design of Additively Manufactured Ni-Based Superalloys Based on Solid Solution Elements[J]. 金属学报, 2026, 62(8): 1395-1404.
[5] YANG He, HOU Ziyong, HU Xingyi, CHENG Jinjun, WANG Yaru, FAN Guohua, HUANG Xiaoxu. Research Progress and Trends in Characterization Techniques for Ultra-High-Strength and Ultra-Fine Stainless Steel Wires: A Perspective Review[J]. 金属学报, 2026, 62(7): 1189-1206.
[6] XU Dingfeng, HAN Feiyang, JIANG Qicheng, WANG Huan, SHANG Liyuan, LU Yiping. Composition Design and Optimization of Microstructure and Properties for an AlCrFeCoNi Low-Expansion Alloy[J]. 金属学报, 2026, 62(6): 1021-1031.
[7] WANG Bin, ZHAO Peng, LIU Jiawei, ZHANG Chunbo, QIN Zhiwei, DONG Honggang, LI Peng. Effect of Heat Treatment on Microstructural Evolution and Mechanical Properties of Inertial Friction Welded Joints for FGH96 Superalloy[J]. 金属学报, 2026, 62(6): 1043-1058.
[8] ZHENG Yufeng, SHEN Yunong. Research Status and Future Directions of Pure Mo and Mo-Based Biodegradable Metals[J]. 金属学报, 2026, 62(5): 905-922.
[9] SHI Yusheng, CHENG Kun, ZHANG Chengjian, LU Jiahao, LI Wei, ZHANG Lichao, WEI Qingsong, CAI Chao. Research Status and Prospects of Additive Manufacturing/Hot Isostatic Pressing Integrated Forming for Difficult-to-Machine Metals[J]. 金属学报, 2026, 62(5): 770-784.
[10] LU Zhaoping, SHEN Yaozu, WANG Xianzhen, CHEN Qiang, TANG Jianguo, ZHANG Xiaobin, YU Yong, JIANG Suihe, LIU Xiongjun, WANG Hui, WU Yuan. High-Entropy Alloys in Extreme Environments: A Perspective on Advantages, Challenges, and Breakthroughs[J]. 金属学报, 2026, 62(5): 743-755.
[11] CHEN Guang, CHEN Fengrui, ZHU Demin, LI Guizhong, LI Luo, SONG Weidong, WANG Zite, XIANG Henggao, CHEN Yang, QI Zhixiang. Polysynthetic Twinned High-Performance TiAl Alloy with Ordered Structures of Functional Units[J]. 金属学报, 2026, 62(4): 541-549.
[12] WANG Jianfeng, XU Zhenmu, LIU Zhan, GAO Zhuanni, ZHAN Xiaohong. Effect of Ultrasonic Vibration on the Microstructure and Strengthening Mechanism of Narrow Gap Laser Welding of TC4 Titanium Alloy[J]. 金属学报, 2026, 62(3): 406-420.
[13] JIANG Zhida, XU Yangyang, YU Jiaxin, LIU Wencai, ZHU Haowen, WU Guohua, SHANG Zhengping. Mechanical and Conductive Properties of Cu/1060Al/Cu Three-Layer Composite Prepared by High-Temperature Oxygen-Free Rolling[J]. 金属学报, 2026, 62(3): 431-444.
[14] JIANG Guolong, ZHOU Xia. Molecular Dynamics Simulation on the Interfacial Behavior of Mg/Mg-Zn-Al Brazing with Ultrasonic Assistance[J]. 金属学报, 2026, 62(2): 372-382.
[15] LI Shaojie, JIN Jianfeng, TIAN Yanzhong, PAN Hucheng, WANG Mingtao, QIN Gaowu. Micromechanics Modeling of the Hetero-Deformation Induced Strengthening and Strain Hardening Effect in Bimodal Structure Copper[J]. 金属学报, 2026, 62(10): 1687-1701.
No Suggested Reading articles found!