|
|
EFFECT OF TEMPERING TEMPERATURE ON LOW TEMPERATURE IMPACT TOUGHNESS OF A LOW CARBON Mn-SERIES BAINITIC STEEL |
GAO Guhui ZHANG Han BAI Bingzhe |
Key Laboratory of Advanced Materials of Ministry of Education, Department of Material Science and Engineering, Tsinghua University, Beijing 100084 |
|
Cite this article:
GAO Guhui ZHANG Han BAI Bingzhe. EFFECT OF TEMPERING TEMPERATURE ON LOW TEMPERATURE IMPACT TOUGHNESS OF A LOW CARBON Mn-SERIES BAINITIC STEEL. Acta Metall Sin, 2011, 47(5): 513-519.
|
Abstract In order to reduce the cost of alloying elements, low carbon Mn series bainitic steels have been developed. The effect of tempering temperature on the microstructure and low temperature impact toughness of a low carbon Mn-series steel has been investigated in the present study. The as rolled steel plate samples with 30 mm thickness were tempered from 280 ℃ to 600 ℃ for 2 h. Metallographic microstructure show that the< microstructure of the as-rolled steel is mostly bainite laths. Bainite laths start to merge and broaden after tempering at 460 ℃, and quasi--polygonal ferrite structures could be revealed after tempering at 600 ℃. Compared with the as-rolled steel, after tempering at 460 ℃, the yield strength of the steel changes slightly, remaining 725 MPa, while the Charpy absorbed energy at $-$40 ℃ increases from 38 J to 146 J, and the ductile-brittle transition temperature (DBTT) decreases from -18 ℃ to -48 ℃. The EBSD and TEM results indicate that the improvement of low temperature impact toughness after tempering at 460 ℃ is caused by the increase of fraction of high angle boundaries and the decrease of effective grain size during the recovery process of bainite laths.
|
Received: 15 October 2010
|
|
Fund: Supported by Science and Technology Project of Bejing (No.D08050303450804) |
[1] Thompson S W, Colvin D J, Krauss G. Metall Trans, 1990; 21A: 1493[2] Park K T, Kim Y S, Lee J G. Mater Sci Eng, 2000; A293: 165[3] Feng C. PhD Thesis, Tsinghua University, Beijing, 2010(冯春. 清华大学博士学位论文, 北京, 2010)[4] Feng C, Fang H S, Bai B Z, Zheng Y K. Acta Metall Sin, 2010; 46: 473(冯春, 方鸿生, 白秉哲, 郑燕康. 金属学报, 2010; 46: 473)[5] Yoo J Y, Choo W Y, ParkTW, KimYW. ISIJ Int, 1995; 35: 1034[6] Dhua S K, Ray A, Sarma D S. Mater Sci Eng, 2001; A318: 197[7] Andrzej K L. J Mater Sci Technol, 2000; 106: 212[8] Marder A R, Krauss G. Trans ASM, 1967; 60: 651[9] Zhu K Y, Bouaziza Olivier, Oberbilliga Carla, Huang M X. Mater Sci Eng, 2010; A527: 6614[10] Naylor J P, Blondeau R. Metall Trans, 1976; 7A: 891[11] Shin S Y, Hong S M, Bae J H, Kim K, Lee S. Metall Mater Trans, 2009; 40A: 2333[12] Takamura J, Mizoguchi S. Proc 6th Int Iron Steel Congr, Nagoya: ISIJ, 1990: 591[13] Han S Y, Shin S Y, Seo C H, Lee H, Bae J H, Kim K, Lee S, Kim N J. Metall Mater Trans, 2009; 40A: 1851[14] Wu H B, Shang C J, Yang S W, Hou H X, Ma Y P, Yu G L. Acta Metall Sin, 2004; 11: 1143(武会宾, 尚成嘉, 杨善武, 侯华兴, 马玉璞, 于功利. 金属学报, 2004; 11: 1143)[15] Dunn C G, Daniels F W. Trans AIME, 1951; 191: 147 |
No Suggested Reading articles found! |
|
|
Viewed |
|
|
|
Full text
|
|
|
|
|
Abstract
|
|
|
|
|
Cited |
|
|
|
|
|
Shared |
|
|
|
|
|
Discussed |
|
|
|
|