激光立体成形零件竖直外侧壁向内倾斜的形成及模型<sup>*</sup>

doi:10.11900/0412.1961.2014.00631

金属学报

2015, Vol. 51

Issue (6): 753-761 DOI: 10.11900/0412.1961.2014.00631

论文

本期目录 | 过刊浏览

激光立体成形零件竖直外侧壁向内倾斜的形成及模型^*

宋梦华,林鑫,刘丰刚,杨海欧,黄卫东(

)

西北工业大学凝固技术国家重点实验室, 西安 710072

FORMATION AND MODELING OF VERTICAL OUTSIDE WALL OF COMPOENTS INCLINING INWARD IN LASER SOLID FORMING

Menghua SONG,Xin LIN,Fenggang LIU,Haiou YANG,Weidong HUANG(

)

State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi'an 710072

引用本文:

宋梦华, 林鑫, 刘丰刚, 杨海欧, 黄卫东. 激光立体成形零件竖直外侧壁向内倾斜的形成及模型^*[J]. 金属学报, 2015, 51(6): 753-761.
Menghua SONG, Xin LIN, Fenggang LIU, Haiou YANG, Weidong HUANG. FORMATION AND MODELING OF VERTICAL OUTSIDE WALL OF COMPOENTS INCLINING INWARD IN LASER SOLID FORMING[J]. Acta Metall Sin, 2015, 51(6): 753-761.

全文: PDF(5571 KB) HTML

摘要:

采用激光立体成形制备了层数逐渐增加的块状试样, 分析了零件竖直外侧壁向内倾斜的原因. 基于利用粉末累积高度重构单道熔覆层横截面轮廓的方法, 构建了描述竖直外侧壁轮廓逐层演化的分析模型. 利用该模型重构了不同单道熔覆层宽高比和激光束有效作用范围下的竖直外侧壁轮廓, 并分析了2者的影响. 结果表明, 逐层叠加过程中, 已沉积的熔覆层将影响之后熔覆层的形成; 由于单道熔覆层的横截面为弧形, 其与激光束相交形成的边界熔池将向零件内部收缩, 从而引起边界单道熔覆层向内收缩及竖直外侧壁向内侧倾斜; 随沉积高度增加, 倾斜程度减小并趋于消失. 初始单道熔覆层宽度一定时, 减小激光束有效作用范围有利于外侧壁趋于竖直但却增大其偏离量; 单道熔覆层宽高比对外侧壁的影响几乎可以忽略.

关键词 ：激光立体成形, 竖直外侧壁, 向内倾斜, 分析模型

Abstract：

The vertical outside wall is prone to incline inward in laser solid forming, which will deteriorate the dimension precision and processing stability. For solving this problem, samples with different amount of deposited layers were prepared and the variation of boundary single-track clad shape and formation of vertical outside wall inclining inward were investigated. Based on the method of constructing cross-section profile of the single-track clad by height of powders accumulated in molten pool, an analytical model was developed to describe the evolution of vertical outside wall during multilayer superimposition. A series of vertical outside walls under different width/height ratios and critical defocus distance were constructed with this model to investigate their influence. Results indicate that the deposited single-track clad will influence the formation of single-track clad under depositing. Due to the arc-like cross-section profile of single-track clad, the molten pool will shrink inward, which leads the outer edge of boundary single-track clad to shrink inward then the vertical outside wall to incline inward. However, this incline will decrease with the increase of deposited height. For the initial single-track clad with fixed width, decreasing critical defocus distance can decrease the inward incline but increase the offset from the preset dimension. The width/height ratio almost has no effect on outside wall.

Key words： laser solid forming vertical outside wall inward incline analytical model

基金资助:^*国家自然科学基金项目51323008, 国家重点基础研究发展计划项目2011CB610402, 国家高技术研究发展计划项目2013AA031103和凝固技术国家重点实验室自主研究课题项目91-QZ-2014资助

	服务

	把本文推荐给朋友
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	宋梦华
	林鑫
	刘丰刚
	杨海欧
	黄卫东
44.8K

链接本文:

https://www.ams.org.cn/CN/10.11900/0412.1961.2014.00631 或 https://www.ams.org.cn/CN/Y2015/V51/I6/753

图1 激光立体成形制备试样的预设形状及竖直外侧壁示意图

图2 不同层数激光立体成形2Cr13不锈钢的外侧壁轮廓

图3 不同层数2Cr13不锈钢顶部边界单道熔覆层横截面轮廓

图4 逐层叠加过程中已沉积边界单道熔覆层对之后熔覆层形状影响的示意图

图5 坐标系及激光束形状示意图

表1 外侧壁轮廓重构参数

图6 外侧壁轮廓重构结果

图7 层间夹角a及尺寸偏离量Δf定义示意图

图8 层间夹角随层数和沉积高度的变化

图9 外侧壁偏离预设位置随层数和沉积高度的变化

[1]	Huang W D,Lin X,Chen J,Liu Z X,Li Y M. Laser Solid Forming—the Rapid and Free Fabricating of High Performance Metal Components. Xi'an: Northwestern Polytechnical University Press, 2007: 1 (黄卫东,林鑫,陈静,刘振侠,李延民. 激光立体成形—高性能致密金属零件的快速自由成形. 西安: 西北工业大学出版社, 2007: 1)
[2]	Liu F, Lin X, Yang G, Song M, Chen J, Huang W. Opt Laser Technol, 2011; 43: 208
[3]	Yang G, Lin X, Liu F, Hu Q, Ma L, Li J, Huang W. Intermetallics, 2012; 22: 110
[4]	Cao J, Liu F, Lin X, Huang C, Chen J, Huang W. Opt Laser Technol, 2013; 45: 228
[5]	Lin X, Cao Y, Wu X, Yang H, Chen J, Huang W. Mater Sci Eng, 2012; A553: 80
[6]	Vrancken B, Thijs L, Kruth J P, Van Humbeeck J. Acta Mater, 2014; 68: 150
[7]	Yang H O, Song M H, Yang D H, Lin X, Chen J, Huang W D. Appl Laser, 2011; 31: 384 (杨海欧, 宋梦华, 杨东辉, 林鑫, 陈静, 黄卫东. 应用激光, 2011; 31: 384)
[8]	Xu Q D, Lin X, Song M H, Yang H O, Huang W D. Acta Metall Sin, 2013; 49: 605 (徐庆东, 林鑫, 宋梦华, 杨海欧, 黄卫东. 金属学报, 2013; 49: 605)
[9]	Huang W D, Lin X. Mater China, 2010; (6): 12 (黄卫东, 林鑫. 中国材料进展, 2010; (6): 12)
[10]	Gu D D, Meiners W, Wissenbach K, Poprawe R. Int Mater Rev, 2012; 57: 133
[11]	Li Y, Yang H, Lin X, Huang W, Li J, Zhou Y. Mater Sci Eng, 2003; A360: 18
[12]	De Oliveira U, Ocelik V, De Hosson J T M. Surf Coat Technol, 2005; 197: 127
[13]	Fallah V, Alimardani M, Corbin S F, Khajepour A. Comp Mater Sci, 2011; 50: 2124
[14]	Zhu G X, Zhang A F, Li D C. Chin J Laser, 2010; (1): 296 (朱刚贤, 张安峰, 李涤尘. 中国激光, 2010; (1): 296)
[15]	Kaplan A, Groboth G. J Manuf Sci Eng, 2001; 123: 609
[16]	Aiyiti W, Zhao W, Lu B, Tang Y. Rapid Prototyping J, 2006; 12: 165
[17]	Li Y, Ma J. Surf Coat Technol, 1997; 90: 1
[18]	Song M, Lin X, Yang G, Cui X, Yang H, Huang W. J Mater Process Technol, 2014; 214: 701
[19]	Bi G, Gasser A, Wissenbach K, Drenker A, Poprawe R. Surf Coat Technol, 2006; 201: 2676
[20]	Tan H, Chen J, Zhang F, Lin X, Huang W. Int J Mach Tools Manuf, 2010; 50: 1
[21]	Zhu G, Li D, Zhang A, Pi G, Tang Y. Opt Laser Technol, 2012; 44: 349
[22]	Liu J, Li L. Opt Laser Technol, 2005; 37: 478
[23]	Liu J. Opt Laser Technol, 2007; 39: 1532
[24]	Tan H, Chen J, Zhang F, Lin X, Huang W. Opt Laser Technol, 2010; 42: 47
[25]	Picasso M, Marsden C F, Wagniere J D, Frenk A, Rappaz M. Metall Mater Trans, 1994; 25B: 281
[26]	Lin J, Hwang B C. Opt Laser Technol, 1999; 31: 571
[27]	Tan H, Zhang F, Wen R, Chen J, Huang W. Opt Laser Eng, 2012; 50: 391

[1]	张媛媛,林鑫,魏雷,任永明. 激光立体成形退火态Zr₅₅Cu₃₀Al₁₀Ni₅粉末的晶化行为[J]. 金属学报, 2017, 53(7): 824-832.
[2]	宋衎,喻凯,林鑫,陈静,杨海欧,黄卫东. 热处理态激光立体成形Inconel 718高温合金的组织及力学性能^*[J]. 金属学报, 2015, 51(8): 935-942.
[3]	刘奋成, 林鑫, 余小斌, 黄春平, 黄卫东. 激光立体成形GH4169合金再结晶过程中的界面和晶体取向演化^*[J]. 金属学报, 2014, 50(4): 463-470.
[4]	刘奋成林鑫杨高林黄春平陈静黄卫东. 不同气氛激光立体成形镍基高温合金Inconel 718的显微组织和力学性能[J]. 金属学报, 2010, 46(9): 1047-1054.
[5]	许小静林鑫黄卫东王亮. 激光立体成形Ti-80%Ni合金显微组织及力学性能[J]. 金属学报, 2010, 46(9): 1081-1085.
[6]	杨模聪林鑫许小静陈静黄卫东. 激光立体成形Ti60--Ti₂AlNb梯度材料的组织与相演变[J]. 金属学报, 2009, 45(6): 729-736.
[7]	刘建涛; 林鑫; 吕晓卫; 陈静; 黄卫东 . Ti-Ti2AlNb功能梯度材料的激光立体成形研究[J]. 金属学报, 2008, 44(8): 1006-1012 .
[8]	许小静; 林鑫; 杨模聪; 陈静; 黄卫东 . 激光立体成形Ti-20%Ni合金枝晶的组织演化[J]. 金属学报, 2008, 44(8): 1013-1018 .
[9]	郑淑国; 朱苗勇 . 多流连铸中间包内钢液流动特性的分析模型[J]. 金属学报, 2005, 41(10): 1073-1076 .

Viewed

Full text

Abstract

Cited

Shared

Discussed