微量Zr对Al-Zn-Mg合金沉淀过程和显微组织参数的影响

金属学报

1985, Vol. 21

Issue (6): 7-108

论文

本期目录 | 过刊浏览

微量Zr对Al-Zn-Mg合金沉淀过程和显微组织参数的影响

林肇琦;赵钢;孙贵经;杨胜坤

东北工学院;东北工学院;东北工学院;东北工学院

EFFECT OF Zr ON PRECIPITATION AND STRUCTURE PARAMETERS OF Al-Zn-Mg ALLOY

by LIN Zhaoqi;ZHAO Gang;SUN Guijing;YANG Shengkun Northeast Institute of Technology; Shenyang

引用本文:

林肇琦;赵钢;孙贵经;杨胜坤. 微量Zr对Al-Zn-Mg合金沉淀过程和显微组织参数的影响[J]. 金属学报, 1985, 21(6): 7-108.
, , , . EFFECT OF Zr ON PRECIPITATION AND STRUCTURE PARAMETERS OF Al-Zn-Mg ALLOY[J]. Acta Metall Sin, 1985, 21(6): 7-108.

全文: PDF(1980 KB)

摘要:

利用硬度计(HV)、光学显微镜和透射电镜系统地研究了微量Zr(0.22％)对Al—5.0Zn-1.75Mg合金的沉淀过程、临界形核温度T′_c和显微组织参数的影响,并与Mn,Cr,Cu的影响进行了比较。结果表明,Zr能明显提高再结晶温度和细化晶粒,但无提高T′_c的能力。低温时效(T_a≤160℃),Zr有抑制GBP、促进MPt长大和提高HV的作用;但高温时效(T_a≥180℃)又有促进这两种参数急剧长大和强烈降低HV的作用。在选定的时效条件下(120—200℃),含Zr合金的PFZ均比无Zr合金窄。文中还讨论了Zr对Al-Zn-Mg合金的作用机理问题。

Abstract：

The effect of 0.22% Zr, and in comparison with Mn, Cr or Cu in theauthors' previous works, on the precipitation, the critical nucleation temperature,T′_c, and the microstructure parameters of a commercial purity Al-5.0Zn-1.75Mgalloy has been studied by means of hardness test, optical microscopy and TEM.The results obtained showed that Zr is the element by which the recrystallizationtemperature of the alloy is substantially raised and the grain size is refined, butthe T′_c is not yet increased. When aged at temperature≤160℃, an additive ofZr in the alloy may inhibit GBP, promote MPt and increase HV. However, whenaged at temperature≥180℃, it may sharply increase these parameters and vio-lently decrease HV. The width of PFZ in the Zr-bearing alloy is always narrowerthan that in the Zr-free alloy under a selected aging condition at 120--200℃. Ithas also been tried to make approach to behaviour of Zr added in the alloy andto contrast among the additives Zr, Mn, Cr and Cu.

收稿日期: 1985-06-18

	服务

	把本文推荐给朋友
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	林肇琦
	赵钢
	孙贵经
	杨胜坤
44.8K

链接本文:

https://www.ams.org.cn/CN/ 或 https://www.ams.org.cn/CN/Y1985/V21/I6/7

1 Kent, K. G,. Weld. Met. Fabr., 35(1967) . 280． 2 1975． p. 135． 3 Truscott. J. M.; Carter. V. E.; Campbell. H. S., J. Inst. Met., 99(2971) , 57． 4 村上阳太郎,轻金属,21(1971) ,702． 5 林肇琦;孙贵经;陈长治;许慧恣,东北工学院学报,(1978) ,№3,22． 6 Schoer, H.; Gruhl,W., Metall,20(1966) ,221． 7 杉山祯彦;福井利安,溶接学会志,35(1966) ,11,70． 8 Develay, R.; Faure. A.; Lehongre. S.; Mugnier, D.; Schroeter, D., Adv. Cryog. Eng., 12 (1967) , 484． 9 Hernaez. J.; Madronero, A., Weld. J., (Weld. Res. Supl.), 51 (1972) , 6, 281． 10 林肇琦;孙贵经,许海峰,东北工学院学报,(1981) ,№2,23． 11 林肇琦;孙贵经,东北工学院学报,(1982) ,№2,93． 12 马场义雄,日本金属学会志,31(1967) ,910． 13 Conserva. M.; Di Russo. E.; Caloni, O., Metall. Trans., 2(1971) , 1227． 14 Westengen. H.; Reiso. O.; Auran, L., Aluminium. 56(1980) , 768． 15 Ohashi. T.; Tchikawa. R., Metall. Trans., 12A(1981) , 546． 16 马场义雄,日本金属学会志,31(1967) ,507． 17 马场义雄,日本金属学会志,31(1967) ,513． 18 马场义雄,轻金属,24(1974) ,547． 19 林肇琦;孙贵经;胡维平;杨胜坤,金属学报,21(1985) ,A119． 20 林肇琦;封冰;孙贵经;杨胜坤,金属学报,19(1983) ,A197． 21 林肇琦;朱继良;孙贵经;杨胜坤,金属学报,20(1984) ,A54． 22 Embury, J. D.; Nicholson, R. B., Acta Metall., 13(1965) , 403． 23 Ozawa, E.; Kimura. H., Acta Metall., 18(1970) , 995． 24 杨胜坤;孙贵经;林肇琦,东北工学院学报,(1985) ,№3,83. 25 1959,p 5.

No related articles found!

Viewed

Full text

Abstract

Cited

Shared

Discussed