TiC Precipitation Behavior and Its Effect on Abrasion Resistance of High Titanium Wear-Resistant Steel

doi:10.11900/0412.1961.2019.00374

Acta Metall Sin

2020, Vol. 56

Issue (4): 661-672 DOI: 10.11900/0412.1961.2019.00374

Current Issue | Archive | Adv Search

TiC Precipitation Behavior and Its Effect on Abrasion Resistance of High Titanium Wear-Resistant Steel

SUN Xinjun(

),LIU Luojin,LIANG Xiaokai,XU Shuai,YONG Qilong

Department of Structrual Steels, Central Iron & Steel Research Institute, Beijing 100081, China

Cite this article:

SUN Xinjun,LIU Luojin,LIANG Xiaokai,XU Shuai,YONG Qilong. TiC Precipitation Behavior and Its Effect on Abrasion Resistance of High Titanium Wear-Resistant Steel. Acta Metall Sin, 2020, 56(4): 661-672.

Download:

HTML

PDF(23077KB)
Export: BibTeX | EndNote (RIS)

Abstract

In general, the wear resistance of traditional low alloy wear-resistant steels can be improved by increasing the hardness of steel matrix, but this significantly deteriorates the processing properties of steel, such as weldability, formability and machinability. Therefore, how to improve the wear resistance of steels without increasing the hardness has become an important issue for the study of wear-resistant steels in recent years. In this work, it is prosposed to introduce ultra-hard TiC particles into the matrix of steel by means of high-Ti microalloying and in situ reaction of TiC in billets (ingots), so as to achieve a significant increase in the wear resistance without increasing the hardness. Seven tested steels with different Ti and C contents were firstly fabricated by smelting, hot rolling and heat treatment, then the morphology, size distribution and fraction of precipitates were characterized by means of OM, SEM, EPMA, TEM, physical-chemical phase analysis, etc. Finally, the wear resistance and its mechanisms of the tested steels were investigated. The results show that TiC particles in the tested steels exhibit an unique trimodal distribution characteristic of "micron-submicron-nanometer". The micron-sized TiC particles were originated from the eutectic reaction of L→γ+TiC occuring at the end of solidification; the eutectic TiC was broken up into small fragments and homogenized gradually during the subsequent hot rolling. The submicron-sized particles were mainly precipitated from austenite at relatively high temperature after solidification, and the nano-sized particles were mainly precipitated from deformed austenite at relatively low temperature during hot rolling. The size of precipitates becomes finer at lower precipitation temperature. The relative precipitation-temperature-time (PTT) diagrams of both submicron-sized and nano-sized TiC were calculated, and it is shown that the most rapid precipitation temperature of the submicron-sized TiC is about 208 ℃ higher than that of the nano-sized TiC. The relative wear resistance of the tested steels is found to increase linearly with increasing TiC fraction, and the improvement of wear resistance is mainly due to the obstruction of micron-sized particles on wear furrow.

Key words: wear-resistant steel high-Ti microalloying TiC precipitation abrasion resistance

Received: 04 November 2019

ZTFLH:

TG142

Fund: National Key Research and Development Program of China(2017YFB0305100)

	Service

	E-mail this article
	Add to citation manager
	E-mail Alert
	RSS
	（）
	Articles by authors
	Xinjun SUN
	Luojin LIU
	Xiaokai LIANG
	Shuai XU
	Qilong YONG

URL:

https://www.ams.org.cn/EN/10.11900/0412.1961.2019.00374 OR https://www.ams.org.cn/EN/Y2020/V56/I4/661

Table 1 Chemical compositions of tested steels

Fig.1 Hot rolling and heat treatment process of tested steels

Fig.2 Schematic of MLS-225 wear test machine

Fig.3 SEM (a~c) and TEM images (d, e) of matrix microstructure of tested steels(a) Ti0 (b) Ti20 (c) Ti60(d) Ti0 (e) Ti20

Fig.4 XRD spectra of precipitate powder obtained by electrolytic extraction of tested steels

Table 2 Phsical-chemical phase analysis results of tested steels

Fig.5 OM images of micron-sized TiC precipitates in Ti60 steel(a) without etching (The dark particles are TiC)(b) etched by Lepera' etchant (The bright particles are TiC)

Fig.6 SEM image of micron-sized TiC precipitates in Ti60 steel

Fig.7 EPMA element maps of micron-sized TiC precipitates in Ti60 steelColor online

Fig.8 EPMA (a) and TEM (b) images of submicron-sized TiC particles in Ti60 steel

Fig.9 TEM image of nano-sized TiC particles in Ti60 steel

Fig.10 TiC particle diameter distributions of Ti60 steel measured by quantitative metallography (a), measured by SAXS (b) and full-scale distribution of particle diameter showing trimodal distribution of "micron-submicron-nanometer" (c)

Fig.11 OM images of as-cast Ti60 steel(a) as-cast secondary dendritic structure (b) TiC precipitated between secondary dendrites

Fig.12 Thermo-Calc thermodynamic calculation of solidification process of Ti60 steel(a) phase tansformations during solidification(b) local magnification of Fig.12a from 1420 ℃ to 1470 ℃

Fig.13 SEM (a~c) and TEM (d~f) images of TiC particles of Ti60 steel quenched at 900 ℃ (a, d) and subsequently subjected to solution treatment at 1200 ℃ (b, e) and 1350 ℃ (c, f)

Fig.14 TiC particle size distribution (0~300 nm) of Ti60 steel subjected to solution treatments at different temperatures

Fig.15 Relative precipitaton-time-temperature (PTT) diagram of TiC precipitates (t_0.05da is the start time of precipitation which corresponds to the fraction precipitated 5%, and t_0da is an almost temperature independent parameter)

Fig.16 Relationships of hardness (a), wear weight loss (b) and relative wear resistance (c) with mass fraction of TiC particles

Fig.17 Obstruction of micron-sized TiC particles marked by circles on wear furrow passage through stopping the furrow (a), deflecting the furrow (b) and stopping the furrow with particle falling off (c)^[5,7] (Insets show the EDS analysis results on the TiC particles marked by circles)

[1]	Pagounis E, Lindroos V K. Development and performance of new hard and wear-resistant engineering materials [J]. J. Mater. Eng. Perform., 1997, 6: 749
[2]	Xie Y B, Zhang S W. The Application Status and Development Strategy Research of Tribology Science and Engineering [M]. Beijing: Higher Education Press, 2009: 1135
[2]	谢友柏, 张嗣伟. 摩擦学科学及工程应用现状与发展战略研究 [M]. 北京: 高等教育出版社, 2009: 1135
[3]	General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, China National Standardization Administration. GB/T 24186-2009 High strength abrasion resistant steel plates for construction machine [S]. Beijing: China Standards Press, 2010
[3]	(中华人民共和国国家质量监督检验检疫总局, 中国国家标准化管理委员会. GB/T 24186-2009 工程机械用高强度耐磨钢板 [S]. 北京: 中国标准出版社, 2010
[4]	Liang X K, Sun X J, Yong Q L, et al. Study on performance of TiC particle reinforced martensite wear-resistant steel [J]. Iron Steel Vanad. Titan., 2017, 38(1): 48
[4]	梁小凯, 孙新军, 雍岐龙等. TiC颗粒强化型马氏体耐磨钢的性能研究 [J]. 钢铁钒钛, 2017, 38(1): 48
[5]	Liu L J. TiC precipitation behavior and its effect on properties in high titanium and high wear-resistant steels [D]. Beijing: Central Iron and Steel Research Institute, 2019
[5]	刘罗锦. 高钛高耐磨钢中TiC析出行为及对性能的影响 [D]. 北京: 钢铁研究总院, 2019
[6]	Liang X K, Sun X J, Yong Q L, et al. Precipitation of TiC in high Ti steel [J]. J. Iron Steel Res., 2016, 28(9): 71
[6]	梁小凯, 孙新军, 雍岐龙等. 高钛钢中TiC析出机制 [J]. 钢铁研究学报, 2016, 28(9): 71
[7]	Liu L J, Liang X K, Liu J, et al. Precipitation process of TiC in low alloy martensitic steel and its effect on wear resistance [J]. ISIJ Int., 2020, 60: 168
[8]	Do?an ? N, Hawk J A, Tylczak J H. Wear of cast chromium steels with TiC reinforcement [J]. Wear, 2001, 250: 462
[9]	Srivastava A K, Das K. Microstructure and abrasive wear study of (Ti, W)C-reinforced high-manganese austenitic steel matrix composite [J]. Mater. Lett., 2008, 62: 3947
[10]	Pagounis E, Lindroos V K, Talvitie M. Influence of reinforcement volume fraction and size on the microstructure and abrasion wear resistance of hot isostatic pressed white iron matrix composites [J] Metall. Mater. Trans., 1996, 27A: 4171
[11]	Ni Z F, Sun Y S, Xue F, et al. Evaluation of electroslag remelting in TiC particle reinforced 304 stainless steel [J]. Mater. Sci. Eng., 2011, A528: 5664
[12]	Tong X, Li F H, Kuang M, et al. Effects of WC particle size on the wear resistance of laser surface alloyed medium carbon steel [J]. Appl. Surf. Sci., 2012, 258: 3214
[13]	Kang N, Ma W Y, Li F H, et al. Microstructure and wear properties of selective laser melted WC reinforced 18Ni-300 steel matrix composite [J]. Vacuum, 2018, 154: 69
[14]	Wei S Z, Zhu J H, Xu L J. Effects of vanadium and carbon on microstructures and abrasive wear resistance of high speed steel [J]. Tribol. Int., 2006, 39: 641
[15]	Wei S Z, Zhu J H, Xu L J. Research on wear resistance of high speed steel with high vanadium content [J]. Mater. Sci. Eng., 2005, A404: 138
[16]	Xu L J, Xing J D, Wei S Z, et al. Study on relative wear resistance and wear stability of high-speed steel with high vanadium content [J]. Wear, 2007, 262: 253
[17]	Xu L J, Wei S Z, Xiao F N, et al. Effects of carbides on abrasive wear properties and failure behaviours of high speed steels with different alloy element content [J]. Wear, 2017, 376-377: 968
[18]	Kan W H, Proust G, Bhatia V, et al. Slurry erosion, sliding wear and corrosion behavior of martensitic stainless steel composites reinforced in-situ with NbC particles [J]. Wear, 2019, 420-421: 149
[19]	Zhang D W, Lei T C, Li F J. Laser cladding of stainless steel with Ni-Cr3C2 for improved wear performance [J]. Wear, 2001, 250: 1372
[20]	Lu Q, He G Q, Yang Y, et al. The friction and wear properties of silicon carbide particle reinforced aluminum matrix composite [J]. Met. Funct. Mater., 2015, 22(2): 41
[20]	卢棋, 何国球, 杨洋等. SiC颗粒增强铝基复合材料的摩擦磨损性能研究 [J]. 金属功能材料, 2015, 22(2): 41
[21]	Ma Y P, Li X L, Wang C H, et al. Microstructure and impact wear resistance of TiN reinforced high manganese steel matrix [J]. J. Iron Steel Res. Int., 2012, 19: 60
[22]	Rong W, Tu J P, Guo S Y. Sliding wear behavior of TiB2 nanoparticle reinforced copper matrix in-situ composites under electric current [J]. Mater. Sci. Forum, 2003, 426-432: 2065
[23]	Shanmugaselvam P, Sivaraj S, Subash P. Investigating the wear and hardness of aluminium LM25 alloy reinforced with nano Al2O3 and nano TiB2 [J]. Mater. Today, 2019, 16: 1130
[24]	Vardavoulias M, Jeandin M, Velasco F, et al. Dry sliding wear mechanism for P/M austenitic stainless steels and their composites containing Al2O3 and Y2O3 particles [J]. Tribol. Int., 1996, 29: 499
[25]	Ramachandra M, Abhishek A, Siddeshwar P, et al. Hardness and wear resistance of ZrO2 nano particle reinforced Al nanocomposites produced by powder metallurgy [J]. Proced. Mater. Sci., 2015, 10: 212
[26]	Do?an ? N, Hawk J A, Tylczak J H, et al. Wear of titanium carbide reinforced metal matrix composites [J]. Wear, 1999, 225-229: 758
[27]	Zhang X N, Lü W J, Zhang D, et al. In situ technique for synthesizing (TiB+TiC)/Ti composites [J]. Scr. Mater, 1999, 41: 39
[28]	Mao X P. Titanium Microalloyed Steel [M]. Beijing: Metallurgical Industry Press, 2016: 1
[28]	毛新平. 钛微合金钢 [M]. 北京: 冶金工业出版社, 2016: 1
[29]	Kang J Y. Precipitation and strengthening behaviors of titanium/vanadium carbides in tempered martensite [D]. Beijing: Central Iron and Steel Research Institute, 2015
[29]	康俊雨. Ti/V碳化物在回火马氏体中的沉淀析出及其强化行为研究 [D]. 北京: 钢铁研究总院, 2015
[30]	Kang J Y, Sun X J, Li Z D, et al. Precipitation and coarsening of TiC and VC in tempering process of low carbon martensite steels [J]. Iron Steel, 2015, 50(10): 64
[30]	康俊雨, 孙新军, 李昭东等. TiC和VC在低碳马氏体钢回火中的析出和粗化 [J]. 钢铁, 2015, 50(10): 64
[31]	Yong Q L. Secondary Phases in Steels [M]. Beijing: Metallurgical Industry Press, 2006: 1
[31]	雍岐龙. 钢铁材料中的第二相 [M]. 北京: 冶金工业出版社, 2006: 1
[32]	Wang Z Q, Yong Q L, Sun X J, et al. An analytical model for the kinetics of strain-induced precipitation in titanium micro-alloyed steels [J]. ISIJ Int., 2012, 52: 1661
[33]	Wang Z Q, Mao X P, Yang Z G, et al. Strain-induced precipitation in a Ti micro-alloyed HSLA steel [J]. Mater. Sci. Eng., 2011, A529: 459
[34]	Wang Z Q, Zhang H, Guo C H, et al. Effect of molybdenum addition on the precipitation of carbides in the austenite matrix of titanium micro-alloyed steels [J]. J. Mater. Sci., 2016, 51: 4996

[1]	HAN Ruyang, YANG Gengwei, SUN Xinjun, ZHAO Gang, LIANG Xiaokai, ZHU Xiaoxiang. Austenite Grain Growth Behavior of Vanadium Microalloying Medium Manganese Martensitic Wear-Resistant Steel[J]. 金属学报, 2022, 58(12): 1589-1599.
[2]	WU Xiang,ZUO Xiurong,ZHAO Weiwei,WANG Zhongyang. Mechanism of TiN Fracture During the Tensile Process of NM500 Wear-Resistant Steel[J]. 金属学报, 2020, 56(2): 129-136.
[3]	XU Shuai, SUN Xinjun, LIANG Xiaokai, LIU Jun, YONG Qilong. Effect of Hot Rolling Deformation on Microstructure and Mechanical Properties of a High-Ti Wear-Resistant Steel[J]. 金属学报, 2020, 56(12): 1581-1591.
[4]	Wenying GUO,Xiaoqiang HU,Xiaoping MA,Dianzhong LI. EFFECT OF TiN PRECIPITATES ON SOLIDIFICATION MICROSTRUCTURE OF MEDIUM CARBON Cr-Mo WEAR RESISTANT STEEL[J]. 金属学报, 2016, 52(7): 769-777.
[5]	WANG Qing ZHA Qianfeng LIU Enxue DONG Chuang WANG Xuejun TAN Chaoxin JI Chunjun. COMPOSITION DESIGN OF HIGH–STRENGTH MARTENSITIC PRECIPITATION HARDENING STAINLESS STEELS BASED ON A CLUSTER MODEL[J]. 金属学报, 2012, 48(10): 1201-1206.
[6]	FU Hanguang. A Study of Abrasion Resistant Cast Fe-B-C Alloy[J]. 金属学报, 2006, 42(5): 545-548 .

No Suggested Reading articles found!

Viewed

Full text

Abstract

Cited

Shared

Discussed