Please wait a minute...
Acta Metall Sin  2020, Vol. 56 Issue (3): 340-350    DOI: 10.11900/0412.1961.2019.00229
Current Issue | Archive | Adv Search |
Microstructures and Tensile Deformation Behavior of Directionally Solidified Mg-xGd-0.5Y Alloys
SUN Heng,LIN Xiaoping(),ZHOU Bing,ZHAO Shengshi,TANG Qin,DONG Yun
School of Resources and Materials, Northeastern University at Qinhuangdao, Qinhuangdao 066004, China
Cite this article: 

SUN Heng,LIN Xiaoping,ZHOU Bing,ZHAO Shengshi,TANG Qin,DONG Yun. Microstructures and Tensile Deformation Behavior of Directionally Solidified Mg-xGd-0.5Y Alloys. Acta Metall Sin, 2020, 56(3): 340-350.

Download:  HTML  PDF(33665KB) 
Export:  BibTeX | EndNote (RIS)      
Abstract  

The poor plastic deformation ability of magnesium alloy, resulted from its close-packed hexagonal structure and only two independent basal <a> slip systems at room temperature that cannot meet the von Mises criterion, has extremely restricted its application. As the α-Mg dendrites grow along with the heat flow in directional solidification, the uniform columnar crystal structures obtained in Mg can effectively improve its mechanical properties. And the mechanical properties of the anisotropic magnesium alloys were heavily affected by the orientation controlled by the directional solidification parameters. In this work, the effects of Gd content (3.0%, 4.5%, 6.0%, mass fraction) on the microstructure and mechanical properties of directionally solidified Mg-xGd-0.5Y alloy were investigated. The tensile deformation behavior at room temperature was analyzed by EBSD technique. The results showed that the Mg-xGd-0.5Y alloys have a longitudinal grain boundary parallel to the heat flow direction and a preferential growth along the normal direction of the (112?0) plane at a withdrawn rate of 3 mm/min. The cross section of the columnar crystal was triangle or crisscross petal in shape, and the secondary branch gradually changed from three branches of 3.0%Gd to four branches of 6.0%Gd. The Mg-6.0Gd-0.5Y alloy with more columnar crystal growing along with <224?3> direction had higher tensile strength (107 MPa) and post-break elongation (32.56%) at room temperature, and its deformation mechanism was basal <a> slipping and {101?2} extension twinning. When the crystal growth directions dispersed (concentrated on the <1?21?0> and <224?3>) in the Mg-3.0Gd-0.5Y alloy, it had low post-break elongation (14.88%) because of poor synergistic deformation ability, which have {101?2} extension twins and {101?1} contraction twins to accommodate strain.

Key words:  Mg-Gd-Y alloy      crystal orientation      twinning mechanism      post-break elongation     
Received:  12 July 2019     
ZTFLH:  TG146.22  
Fund: National Natural Science Foundation of China(51775099);National Natural Science Foundation of China(51675092);Natural Science Foundation of Hebei Province(E2018501033)

URL: 

https://www.ams.org.cn/EN/10.11900/0412.1961.2019.00229     OR     https://www.ams.org.cn/EN/Y2020/V56/I3/340

Fig.1  Dimension diagram of tensile specimen (unit: mm)
Fig.2  OM images of longitudinal (a, c, e) and transverse (b, d, f) sections of directionally solidified Mg-xGd-0.5Y alloy(a, b) x=3.0 (c, d) x=4.5 (e, f) x=6.0
Fig.3  Pseudo binary phase diagram of Mg-Gd-Y ternary alloy at 0.5Y section
Fig.4  XRD spectra of the Mg-xGd-0.5Y alloys and standard Mg powder
Fig.5  Stress-strain curves (a) and feature distribution map (b) of the Mg-xGd-0.5Y alloys tensioned at room temperature
Fig.6  Microstructures of directionally solidified Mg-6.0Gd-0.5Y alloy stretched to 25% at room temperature(a) macromorphology of the alloy (b~g) magnifications of the boxes of D (b), E (c), F (d, e), H (f) and I (g) in Fig.6a, respectively
Fig.7  EBSD analyses of the tensile deformation microstructures of directionally solidified Mg-6.0Gd-0.5Y alloy, including Euler map (a), large-angle grain boundary map (b), small-angle grain boundary and twin type diagram (c), strain contouring map (d), misorientation distribution map (e), basal <a> slip Schmid factor map (f) and X0 inverse pole figure (g)Color online
Fig.8  Microstructures of directionally solidified Mg-3.0Gd-0.5Y alloy stretched to 10% at room temperature(a) macromorphology (b~e) magnifications of the boxes of D (b), E (c) and F (d, e) in Fig.8a, respectively
Fig.9  EBSD analyses of the tensile deformation microstructure of directionally solidified Mg-3.0Gd-0.5Y alloy, including Euler map (a), large-angle grain boundary map (b), small-angle grain boundary and twin type diagram (c), strain contouring map (d), misorientation distribution map (e), basal <a> slip Schmid factor map (f) and X0 inverse pole figure (g)Color online
[1] Liu C M, Ji R F, Zhou H T, et al. Research and development progress of damping capacity of magnesium and magnesium alloys [J]. Chin. J. Nonferrous Met., 2005, 15: 1319
[1] 刘楚明, 纪仁峰, 周海涛等. 镁及镁合金阻尼特性的研究进展 [J]. 中国有色金属学报, 2005, 15: 1319
[2] Wan D Q, Wang J C, Yang G C. A study of the effect of Y on the mechanical properties, damping properties of high damping Mg-0.6%Zr based alloys [J]. Mater. Sci. Eng., 2009, A517: 114
[3] Wang J F, Gao S, Pan F S, et al. Influence of process technology on mechanical and damping properties of ZK60 magnesium alloys [J]. Chin. J. Nonferrous Met., 2009, 19: 821
[3] 王敬丰, 高 珊, 潘复生等. 加工工艺对ZK60镁合金力学性能和阻尼性能的影响 [J]. 中国有色金属学报, 2009, 19: 821
[4] Kocks U F, Chandra H. Slip geometry in partially constrained deformation [J]. Acta Metall., 1982, 30: 695
[5] Hu Y K, Li Q S, Li J W, et al. Research on structure of Mg-3Zn-Y alloy and mechanical property under directional solidification [J]. Heavy Cast. Forg., 2017, (6): 6
[5] 胡延昆, 李秋书, 李建文等. 定向凝固下Mg-3Zn-Y合金组织和力学性能研究 [J]. 大型铸锻件, 2017, (6): 6
[6] Mabuchi M, Kobata M, Chino Y, et al. Tensile properties of directionally solidified AZ91 Mg alloy [J]. Mater. Trans., 2003, 44: 436
[7] Liu S J, Yang G Y, Jie W Q. Microstructure, microsegregation, and mechanical properties of directional solidified Mg-3.0Nd-1.5Gd alloy [J]. Acta Metall. Sin. (Engl. Lett)., 2014, 27: 1134
[8] Lin X P, Zhao T B, Dong Y, et al. Room-temperature tensile properties of a directionally solidified magnesium alloy and its deformation mechanism dominated by contraction twin and double twin [J]. Mater. Sci. Eng., 2017, A700: 681
[9] Molodov K D, Al-Samman T, Molodov D A, et al. On the ductility of magnesium single crystals at ambient temperature [J]. Metall. Mater. Trans., 2014, 45A:3275
[10] Yang H. Mechanical property and twinning behavior of Mg and Mg-Sn alloy single crystal in directional solidification [D]. Chongqing: Chongqing University, 2016
[10] 杨 鸿. 定向凝固下镁及镁锡合金单晶的力学性能和孪生行为研究 [D]. 重庆: 重庆大学, 2016
[11] Pettersen K, Lohne O, Ryum N. Dendritic solidification of magnesium alloy AZ91 [J]. Metall. Trans., 1990, 21A: 221
[12] Du J L, Guo Z P, Zhang A, et al. Correlation between crystallographic anisotropy and dendritic orientation selection of binary magnesium alloys [J]. Sci. Rep., 2017, 7: 13600
[13] Shuai S S, Guo E Y, Wang M Y, et al. Anomalous α-Mg dendrite growth during directional solidification of a Mg-Zn alloy [J]. Metall. Mater. Trans., 2016, 47A: 4368
[14] Yang M, Xiong S M, Guo Z. Effect of different solute additions on dendrite morphology and orientation selection in cast binary magnesium alloys [J]. Acta Mater., 2016, 112: 261
[15] Wang M Y, Xu Y J, Jing T, et al. Growth orientations and morphologies of α-Mg dendrites in Mg-Zn alloys [J]. Scr. Mater., 2012, 67: 629
[16] Li J L, Wu D, Chen R S, et al. Anomalous effects of strain rate on the room-temperature ductility of a cast Mg-Gd-Y-Zr alloy [J]. Acta Mater., 2018, 159: 31
[17] Zhang G S, Zhang Z M, Li X B, et al. Effects of repetitive upsetting-extrusion parameters on microstructure and texture evolution of Mg-Gd-Y-Zn-Zr alloy [J]. J. Alloys Compd., 2019, 790: 48
[18] Liu S J. Researches on the solidification characteristic and mechanical properties of Mg-Zn-Gd-based magnesium alloy [D]. Xi'an: Northwestern Polytechnical University, 2016
[18] 刘少军. Mg-Zn-Gd系镁合金的凝固特性及其力学性能研究 [D]. 西安: 西北工业大学, 2016
[19] Zheng W, Wang G C, Wu T. Establishment of constitutive equation of material in region affected by grain boundary and numerical simulation of micro-bulk-forming [J]. J. Mech. Eng., 2011, 47(22): 31
[19] 郑 伟, 王广春, 吴 涛. 微体积成形晶界影响区域材料本构方程的构建及有限元模拟 [J]. 机械工程学报, 2011, 47(22): 31
[20] He J J, Mao Y, Lu S L, et al. Texture optimization on Mg sheets by preparing soft orientations of extension twinning for rolling [J]. Mater. Sci. Eng., 2019, A760: 174
[21] Wang Y C. Study on the anisotropy of mechanical behavior and deformation mechanisms of AZ31 Mg alloys by numerical simulation [D]. Shenyang: Northeastern University, 2014
[21] 王运程. AZ31镁合金各向异性力学行为及微观形变机制的模拟研究 [D]. 沈阳: 东北大学, 2014
[22] Cao X H. Monte carlo method of simulation grain growth [D]. Shanghai: East China University of Science and Technology, 2014
[22] 曹小虎. 晶粒生长的蒙特卡洛模拟方法研究 [D]. 上海: 华东理工大学, 2014
[23] Yu H H. Research on the relationship between boundary character and strengthening in Mg alloys [D]. Chongqing: Chongqing University, 2018
[23] 余辉辉. 镁合金中界面特征与细晶强化的关系研究 [D]. 重庆: 重庆大学, 2018
[24] Wang J, Beyerlein I J, Tomé C N. An atomic and probabilistic perspective on twin nucleation in Mg [J]. Scr. Mater., 2010, 63: 741
[25] Wang Z Q, Chapuis A, Liu Q. Simulation of mechanical behavior of AZ31 magnesium alloy during twin-dominated large plastic deformation [J]. Trans. Nonferrous Met. Soc. China, 2015, 25: 3595
[1] LIU Jinlai, YE Lihua, ZHOU Yizhou, LI Jinguo, SUN Xiaofeng. Anisotropy of Elasticity of a Ni Base Single Crystal Superalloy[J]. 金属学报, 2020, 56(6): 855-862.
[2] HU Bin,LI Shusuo,PEI Yanling,GONG Shengkai,XU Huibin. Influence of Small Misorientation from <111> on Creep Properties of a Ni-Based Single Crystal Superalloy[J]. 金属学报, 2019, 55(9): 1204-1210.
[3] Li WANG,Zhongjiao ZHOU,Shaohua ZHANG,Xiangdong JIANG,Langhong LOU,Jian ZHANG. CRACK INITIATION AND PROPAGATION AROUND HOLES OF Ni-BASED SINGLE CRYSTAL SUPERALLOY DURING THERMAL FATIGUE CYCLE[J]. 金属学报, 2015, 51(10): 1273-1278.
[4] LIU Fencheng, LIN Xin, YU Xiaobin, HUANG Chunping, HUANG Weidong. EVOLUTION OF INTERFACE AND CRYSTAL ORIENTATION OF LASER SOLID FORMED GH4169 SUPERALLOY DURING RECRYSTALLIZATION[J]. 金属学报, 2014, 50(4): 463-470.
[5] JIA Yuxian JIN Tao LIU Jinlai SUN Xiaofeng HU Zhuangqi. ANISOTROPIC CREEP IN A Ni-BASED SINGLE CRYSTAL SUPERALLOY[J]. 金属学报, 2009, 45(11): 1364-1369.
[6] WU Donghai;HU Gengxiang (Department of Materials Science; Shanghai Jiaotong University; Shanghai 200030)INUI Haruyuki; YAMAGUCHI Masaharu (Kyoto University; Kyoto 606-01; Japan). DEFORMATION BEHAVIOR OF γ-TiAl SINGLE CRYSTALS AT DIFFERENT TEMPERATURES[J]. 金属学报, 1998, 34(1): 39-44.
[7] ZHANG Guangping;WANG Zhongguang (State Key Laboratory for Fracture and Fatigue of Materials; Institute of Metal Research; Chinese Academy of Sciences;Shenyang 110015). EFFECTS OF CRYSTAL ORIENTATION AND LOAD MODE ON FATIGUE BEHAVIOR IN Ni_3Al ALLOY SINGLE CRYSTALS[J]. 金属学报, 1997, 33(10): 1009-1014.
[8] HE Guo;LI Jianguo;MAO Hiemin;FU Hengzhi(Northwestern Polytechnical University;Hi'an 710072)(Manuscript received 1994-09-13.in revised form 1995-03-13). INFLUENCE OF CRYSTAL ORIENTATION ON THE PRIMARY DENDRITE ARM SPACING OF A SINGLE CRYSTAL SUPERALLOY[J]. 金属学报, 1995, 31(7): 309-314.
[9] XIA Yuebo; ZHANG Tianyi (State Key Laboratory for Fracture and Failure of Materials; Institute of Metal Research; Academia Sinica; Shenyang) DENG Jun (Shenyang Polytechnical University). EFFECT OF ORIENTATION ON STRESS RESPONSE, FRICTION STRESS AND BACK STRESS DURING CYCLIC DEFORMATION IN AI SINGLE CRYSTALS.[J]. 金属学报, 1992, 28(8): 42-48.
[10] JIN Nengyun Shanghai Jiaotong University. CYCLIC DEFORMATION OF FCC CRYSTALS AND ITS DISLOCATION INTERACTION MODEL Ⅰ. CYCLIC DEFORMATION OF COPPER SINGIE CRYSTALS[J]. 金属学报, 1988, 24(5): 299-310.
No Suggested Reading articles found!