Acta Metall Sin  2012, Vol. 48 Issue (3): 277-282    DOI: 10.3724/SP.J.1037.2011.00504

论文 Current Issue | Archive | Adv Search |

MODIFICATION OF STRESS DISTRIBUTION ALONG THE THICKNESS OF (Ti, Al)N COATINGS AND PREPARATION OF THE COATINGS WITH LARGE THICKNESS

ZHAO Shengsheng1), CHENG Yu1), CHANG Zhengkai2), WANG Tiegang2), SUN Chao2)

1) Shenzhen Polytechnic, Shenzhen 518055 2) Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016

ZHAO Shengsheng CHENG Yu CHANG Zhengkai WANG Tiegang SUN Chao. MODIFICATION OF STRESS DISTRIBUTION ALONG THE THICKNESS OF (Ti, Al)N COATINGS AND PREPARATION OF THE COATINGS WITH LARGE THICKNESS. Acta Metall Sin, 2012, 48(3): 277-282.

Abstract References Related Articles Recommended Metrics Download:  PDF(2456KB)  Export:  BibTeX | EndNote (RIS)       Abstract  The effects of N2 partial pressure on the depth distribution of residual stresses and mechanical properties in the (Ti, Al)N coatings prepared by arc ion plating (AIP), were investigated. The results indicate that the stress distribution was roughly uniform when the coatings were deposited under lower NN2 partial pressure. As the partial pressure increased the stress distribution to exhibited a “bell” shape and the average stresses of coatings increased remarkably. The mechanism of stress distribution was analyzed by characterizing the microstructure and the composition of the coating. The N2 partial pressure also affected the hardness of coatings and the coating/substrate adhesion obviously. The higher the N2 partial pressure is, the higher the coating hardness but the lower the adhesion. The stress distribution can be modified and the adhesion of the coating/substrate can be improved by optimizing N2 partial pressure parameter. Finally, the coatings with the thickness over 130 μm were successfully directly deposited on the substrate through optimizing the N2 partial pressure. Key words:  (Ti, Al)N      hard coating      stress distribution      stress modification      N2 partial pressure      Received:  08 August 2011      ZTFLH:  TG174.444   Fund:  Supported by National Natural Science Foundation of China (No.50471072) and Guangdong Natural Science Foundation (No.S2011040004468}) Service E-mail this article Add to citation manager E-mail Alert RSS （） Articles by authors DIAO Sheng-Sheng CHENG Yu CHANG Zheng-Kai YU Tie-Gang XUN Tiao URL:  https://www.ams.org.cn/EN/10.3724/SP.J.1037.2011.00504     OR     https://www.ams.org.cn/EN/Y2012/V48/I3/277 [1] Palmers J, Van Stappen M. Surf Coat Technol, 1995; 76/77: 363 [2] Shew B Y, Huang J L. Surf Coat Technol, 1995; 71: 30 [3] Cheng Y H, Tay B K, Lau S P, Shi X, Chua H C. Thin Solid Films, 2000; 379: 76 [4] Zhao S S, Yang Y, Li J B, Gong J, Sun C. Surf Coat Technol, 2008; 202: 5185 [5] Huang J H, Ma C H, Chen H. Surf Coat Technol, 2006; 201: 3199 [6] Sun X L, Fan Z X, Shao J D. Acta Metall Sin, 2007; 43: 307 (孙喜莲, 范正修, 邵建达. 金属学报, 2007; 43: 307) [7] Song G H, Zheng J D, Liu Y, Sun C. J Synth Crys, 2004; 33: 422 [8] Stein C, Keunecke, M, Bewilogua K, Chudoba T, Koelker W, van den Berg H. Surf Coat Technol, 2011; 205(spec): 2 [9] Wu P, Zhou C Z, Tang X N. Acta Metall Sin, 1994; 30: 508 (吴萍, 周昌炽, 唐西南. 金属学报, 1994; 30: 508) [10] PalDey S, Deevi S C. Mater Sci Eng, 2003; A361: 1 [11] Manaila R, Devenyi A, Biro D, David L, Barna P B, Kovacs A. Surf Coat Technol, 2002; 151: 21 [12] Li M S, Wang F H. Surf Coat Technol, 2003; 167: 197 [13] Sanchette F, Czerwiec T. Surf Coat Technol, 1997; 96: 184 [14] Paul H M, Christian M, Lars H, Helmut C. Prog Mater Sci, 2006; 51: 1032 [15] Zhao S S, Du H, Hua W G, Gong J, Li J B, Sun C. J Mater Res, 2007; 22: 2659 [16] Yang H G, Li S, Zhang R L. China Surf Eng, 2009; 22(2): 20 (杨洪刚, 李曙, 张荣禄.中国表面工程, 2009; 22(2): 20) [17] Wang T G, Zhao S S, Hua W G, Li J B, Gong J, Sun C. Mater Sci Eng, 2010; A527: 454 [18] Zhou Y, Rao G B, Wang J Q, Zhang B, Yu Z M, Ke W, Han E H. Thin Solid Films, 2011; 519: 2207 [19] Wan X S, Zhao S S, Yang Y, Gong J, Sun C. Surf Coat Technol, 2010; 204: 1800 [20] Yang Y, Zhao S S, Gong J, Jiang X, Sun C. J Mater Sci Technol, 2011; 27: 385 [21] Josson B, Hogmark S. Thin Solid Films, 1984; 114: 257 [22] Zheng J D, Zou Y S, Song G H, Gong J, Liu Y, Sun C, Wen L S. Acta Metall Sin, 2004; 40: 745 (郑静地, 邹友生, 宋贵宏, 宫骏, 刘 越, 孙超, 闻立时. 金属学报, 2004; 40: 745) [23] Thornton J A. Ann Rev Mater Sci, 1977; 7: 239 [24] Tian M B, Liu D L. Film Science and Technology Handbook (1st Vol.). Beijing: China Machine Press, 1980: 7 (田民波, 刘德令. 薄膜科学与技术手册 (上). 北京: 机械工业出版社, 1980: 7) [25] Carvalho N J M, Zoestbergen E, Kooi B J, Hosson D J T M. Thin Solid Films, 2003; 429: 179 [1] Xudong SUI,Guojian LI,Qiang WANG,Xuesi QIN,Xiangkui ZHOU,Kai WANG,Lijian ZUO. PREPARATION OF Ti1-xAlxN COATING IN CUTTING TITANIUM ALLOY AND ITS CUTTING PERFORMANCE[J]. 金属学报, 2016, 52(6): 741-746. [2] LIANG Yingchun PEN Hongmin BAI Qingshun. MOLECULAR DYNAMICS SIMULATION OF NANOMETRIC CUTTING CHARACTERISTICS OF SINGLE CRYSTAL Cu[J]. 金属学报, 2009, 45(10): 1205-1210. [3] MA Shengli; XU Jian; JIE Wanqi; XU Kewei; M. G. J. Veprek--Heijman; S. Veprek. Characterization of Microstructure and Hardness of PCVD DepositedTi1-xAlx N Hard Coatings[J]. 金属学报, 2004, 40(6): 669-. [4] CAO Li;JIANG Chiping;YAO Zhongkai;LEI Tingquan Harbin Institute of Technology. FRACTURE BEHAVIOUR OF SiC WHISKER REINFORCED Al COMPOSITES[J]. 金属学报, 1989, 25(3): 113-118. No Suggested Reading articles found! Viewed Full text Abstract Cited   Shared      Discussed