机械磨擦制备的Fe-20Mn-3Al-3Si钢表面相变强化层*
陈 燕, 女, 1989年生, 硕士生
收稿日期: 2013-09-09
修回日期: 2014-01-23
网络出版日期: 2014-04-20
基金资助
*国家重点基础研究发展计划项目2009CB623704, 国家自然科学基金项目51071064, 51171063和51371081以及湖南省科研条件创新专项项目2011TT1003资助
A PHASE-TRANSFORMATION-STRENGTHENED SURFACE LAYER ON Fe-20Mn-3Al-3Si STEEL FABRICATED BY MECHANICAL GRINDING
Received date: 2013-09-09
Revised date: 2014-01-23
Online published: 2014-04-20
Supported by
Supported by National Basic Research Program of China (No.2009CB623704), National Natural Science Foundation of China (Nos.51071064, 51171063 and 51371081) and Instrumental Innovation Foundation of Hunan Province (No.2011TT1003)
采用表面机械磨擦处理(SMGT)在Fe-20Mn-3Al-3Si钢的表面制备梯度相变强化层, 并研究了该强化层的微观组织和硬度. 结果表明, 在SMGT 过程中, Fe-20Mn-3Al-3Si钢的表层非常容易发生γ→ε→α马氏体相变. SMGT相变受晶粒取向和外力的共同影响: 在小载荷SMGT下, 晶粒的{111}或者{110}晶面越靠近试样的表面越容易形成片条状组织; 在大载荷SMGT下, 表层晶粒严重细化, 次表层中片条组织最多, 然后片条组织数量逐渐减少. 室温车削形成的强化层厚度大于400 μm, 硬度在表面最高(450 HV), 然后随深度增加而逐渐下降至基体硬度(约220 HV). 另外, SMGT强化层的热稳定性高, 经400 ℃, 1 h退火后其微观组织和硬度基本不变.
陈燕 , 伍翠兰 , 谢盼 , 陈汪林 , 肖辉 , 陈江华 . 机械磨擦制备的Fe-20Mn-3Al-3Si钢表面相变强化层*[J]. 金属学报, 2014 , 50(4) : 423 -430 . DOI: 10.3724/SP.J.1037.2013.00568
In the last decade, transformation induced plasticity (TRIP) aided steels and twinning induced plasticity (TWIP) aided steels have attracted a great deal of attention due to their high strength and exceptional ductility at room temperature. In the present work, a TRIP/TWIP austenite steel with the composition as Fe-20Mn-3Al-3Si has been investigated by means of surface mechanical grinding treatment (SMGT) since it is an alloy with low stacking fault energy. The e-M and/or a-M transformations can easily occur in the steel when deformed at room temperature. It is shown that a gradient phase-transformation-strengthened (PTS) surface layer can be formed on bulk Fe-20Mn-3Al-3Si steel by SMGT at room temperature, due to the martensitic transformation of γ→ε→α on its surface. The formation of martensitic phases is dependent on the strain applied and the orientation of grains. The more the {111} or the {110} planes of grains are parallel to the specimen surface plane, the easier the martensitic laths are to be formed in the gains. The total thickness of the PTS surface layer, which formed in the process of turning at room temperature, can be more than 400 μm, but its microstructure and hardness change with depth. The top PTS layer consists of nanometer sized grains while the sublayer contains a great many of martensite laths mixed with deformation twins. With increasing of the depth, the numbers of laths decrease. Correspondingly, the micro-hardness continuously decreases with the depth from 450 HV to about 220 HV (the hardness of the matrix). The formed PTS layer has a good thermodynamic stability, so that its microstructure and hardness almost do not change after annealed at 400 ℃ for 1 h.
| [1] | Grassel O, Kruger L, Frommeyer G, Meyer L W. Int J Plast, 2000; 16: 1391 |
| [2] | Frommeyer G, Brx U, Neumann P. ISIJ Int, 2003; 3: 438 |
| [3] | Mi Z L, Tang D, Yan L, Guo J. J Mater Sci Technol, 2005; 4: 451 |
| [4] | Ding H, Ting Z Y, Li W, Wang M, Song D. J Iron Steel Res Int, 2006; 6: 66 |
| [5] | Long C X. Master Thesis, Hunan University, Changsha, 2012 |
| [5] | (龙彩霞. 湖南大学硕士学位论文, 长沙, 2012) |
| [6] | Xie P, Wu C L, Ai B B, Chen W L, Chen Y, Chen Y. J Chin Electr Microsc Soc, 2013; 32: 211 |
| [6] | (谢 盼, 伍翠兰, 艾倍倍, 陈汪林, 陈 燕, 陈 亚. 电子显微学报, 2013; 32: 211) |
| [7] | Wu C L, Ai B B, Xie P, Chen W L, Li J M. J Hunan Univ (Nat Sci), 2013; 40(6): 80 |
| [7] | (伍翠兰, 艾倍倍, 谢 盼, 陈汪林, 李久茂. 湖南大学学报(自然科学版), 2013; 40(6): 80) |
| [8] | Long C X, Wu C L, Wang S B. J Hunan Univ (Nat Sci), 2012; 39(7): 70 |
| [8] | (龙彩霞, 伍翠兰, 王双宝. 湖南大学学报(自然科学版), 2012; 39(7): 70) |
| [9] | Ding H, Ding H, Song D, Tang Z Y, Yang P. Mater Sci Eng, 2011; A528: 868 |
| [10] | Ding H, Ding H, Tang Z Y, Song D, Yang P. Chin J Mater Res, 2009; 4: 375 |
| [10] | (丁 昊, 丁 桦, 唐正友, 宋 丹, 杨 平. 材料研究学报, 2009; 4: 375) |
| [11] | Zhang S J, Ding H, Ding H, Zeng J M, Tang Z Y. J Mater Metall, 2009; 3: 198 |
| [11] | (张淑娟, 丁 桦, 丁 昊, 曾建敏, 唐正友. 材料与冶金学报, 2009; 3: 198) |
| [12] | Wang Z B, Yong X P, Tao N R, Li S, Liu G, Lv J, Lu K. Acta Metall Sin, 2001; 37: 1251 |
| [12] | (王镇波, 雍新平, 陶乃镕, 李 曙, 刘 刚, 吕 坚, 卢 柯. 金属学报, 2001; 37: 1251) |
| [13] | Tao N R, Wang Z B, Tong W P, Sui M L, Lu J, Lu K. Acta Mater, 2002; 50: 4603 |
| [14] | Chen X H, Lu J, Lu L, Lu K. Scr Mater, 2005; 52: 1039 |
| [15] | Liu G, Wang S C, Lou X F, Lu J, Lu K. Scr Mater, 2001; 44: 1791 |
| [16] | Li W L, Tao N R, Lu K. Scr Mater, 2008; 59: 546 |
| [17] | Fang T H, Li W L, Tao N R, Lu K. Science, 2011; 331: 1587 |
| [18] | Zheng Z J, Gao Y. J Mater Eng, 2008; (10): 137 |
| [18] | (郑志军, 高 岩. 材料工程, 2008; (10): 137) |
| [19] | Amar K D, David C M, Martin C M, John G S, David K M. Scr Mater, 2004; 50: 1445 |
| [20] | Cong Q Z. Two-dimensional Polycrystalline X-ray Diffraction. Beijing: Science Press, 1997: 37 |
| [20] | (从秋滋. 多晶二维X射线衍射. 北京: 科学出版社, 1997: 37) |
| [21] | Yong X P, Liu G, Lv J, Lu K. Acta Metall Sin, 2002; 38: 157 |
| [21] | (雍兴平, 刘 刚, 吕 坚, 卢 柯. 金属学报, 2002; 38: 157) |
| [22] | Kleber X, PirfoBarroso S. Mater Sci Eng, 2010; A527: 6046 |
| [23] | Yu Q M, Hu B F, Chen H M. J Beijing Univ Sci Technol, 2002; 26: 614 |
| [23] | (余泉茂, 胡本芙, 陈焕铭. 北京科技大学学报, 2002; 26: 614) |
| [24] | Wang B Q, Gu N J, Guo S Z, Ma X L. Acta Metall Sin, 2002; 38: 474 |
| [24] | (王宝奇, 谷南驹, 郭素珍, 马晓莉. 金属学报, 2002; 38: 474) |
| [25] | Wang H T, Tao N R, Lu K. Acta Mater, 2012; 60: 4027 |
/
| 〈 |
|
〉 |
