Ti-12Co-5Al合金的超塑变形

金属学报

1994, Vol. 30

Issue (17): 223-228

论文

本期目录 | 过刊浏览

Ti-12Co-5Al合金的超塑变形

刘庆;杨王玥;陈国良;吴以琴

北京科技大学;西北有色金属研究院

SUPERPLASTIC DEFORMATION OF Ti-12Co-5Al ALLOY

LIU Qing; YANG Wangyue; CHEN Guoliang (University of Science and Technology Beijing); WU Yiqin (Northwest Institute of Nonferrous Metal Research; Xi'an)

引用本文:

刘庆;杨王玥;陈国良;吴以琴. Ti-12Co-5Al合金的超塑变形[J]. 金属学报, 1994, 30(17): 223-228.
, , , . SUPERPLASTIC DEFORMATION OF Ti-12Co-5Al ALLOY[J]. Acta Metall Sin, 1994, 30(17): 223-228.

全文: PDF(454 KB)

摘要: 采用合适的冶炼及形变热处理工艺获得了具有超细化α－Ｔｉ／Ｔｉ２Ｃｏ双相组织的Ｔｉ－１２Ｃｏ－５Ａｌ合金板材，该合金呈现出优异的高速低温超塑性，在７００℃和３×１０－２ｓ－１的高应变速率条件下延伸率超过２０００％。微观组织研究表明超塑变形促进了Ｔｉ２Ｃｏ粒子的长大和形状变化，在塑性应变高达１５５０％时试样中仍无孔洞产生，应变硬化和应变速率硬化的共同作用是该合金具有优异超塑性的根本原因。

关键词 ：Ｔｉ－Ｃｏ－Ａｌ合金, 超塑变形, 塑性稳定性, 第二相长大

Abstract：An Ti-12Co-SAl alloy sheet with an ultra fine α-Ti/Ti2Co microstructure was prepared by proper smelting and thermomechanical treatment. An excellent superplastic elongation more than 2000% was obtained at high strain rate of3 ×10-2 s-1 and under relatively low temperature of 700℃. Microstructural study indicates that the supepolastic defomration promotes the grain growth and shape change of the Ti2Co intermetallic particles.No cavity was found in the specimen after even superplastically deformed to 1550%. The combination of strain hardening, resulted from the coarsening of α－Ti grains and Ti2Co particles, together with the strain rate hardening is considered to be the main reason why the alloy exhibits excellent superplasticity.

Key words： Ti-Co-Al alloy superplastic deformation plastic stability second phase growth

基金资助:中国博士后科学基金;;国家青年自然科学基金

	服务

	把本文推荐给朋友
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	刘庆
	杨王玥
	陈国良
	吴以琴
44.8K

链接本文:

https://www.ams.org.cn/CN/ 或 https://www.ams.org.cn/CN/Y1994/V30/I17/223

1GhoshAK,HamiltonCH．MetallTrans,1979;10A:6992PatonNE,HamiltonCH．MetallTrans,1979;10A:2413WertJA,PatonNE．MetallTrans,1983;14A:25354LeaderJR,NealDF,HammondC．MetallTrans,1986;17A:935FrommeyerG,CzarnowskiPV．ZMetallk,1990;81:7566LIUQing,YangWangyue,ChenGuoliang．ActaMetallMater,tobepublished7刘庆,黄晓旭,姚枚,杨金凤,金属学报,1991;27:B4148LiuQing,YangJinfeng,YaoMei．ScrMetallMater,199l;25:109

[1]	刘志义; 刘冰 . 脉冲电流对2091Al-Li合金超塑变形机理的影响[J]. 金属学报, 2000, 36(9): 944-951 .
[2]	颜莹; 张彩碚; 刘渤然 . 铝合金及其复合材料在超塑变形过程中的正电子寿命谱[J]. 金属学报, 1999, 35(12): 1284-1288 .
[3]	李淼泉;吴诗惇. LY12CZ铝合金超塑变形时的电场效应[J]. 金属学报, 1995, 31(6): 272-276.
[4]	刘庆;刘振纲;姚枚. 温轧态Al-Li-Cu-Mg-Zr合金超塑变形后空洞行为与残余强度的研究[J]. 金属学报, 1993, 29(9): 25-30.
[5]	刘庆;黄晓旭;姚枚;杨金凤. 拉伸条件对Al-Li-Cu-Mg-Zr合金超塑变形行为的影响[J]. 金属学报, 1991, 27(6): 126-132.
[6]	蒋兴钢;崔建忠;马龙翔. 高强度7475Al合金超塑变形空洞形状变化的分形描述[J]. 金属学报, 1990, 26(4): 144-147.
[7]	崔建忠;马龙翔. 超塑变形中的晶粒形状效应[J]. 金属学报, 1988, 24(4): 354-361.
[8]	崔建忠;马龙翔. 超塑变形的特征参数[J]. 金属学报, 1988, 24(1): 92-96.

Viewed

Full text

Abstract

Cited

Shared

Discussed