金属学报  1982, Vol. 18 Issue (1): 85-134

论文 本期目录 | 过刊浏览 |

Cr含量对30CrNi5MoV钢“软化”效应的探讨

鲁肇俊;吴宝榕;吴佩芝;李桂芬;王琪;卢鸿修;李雪缘;金钦乾;汪德根

冶金工业部钢铁研究总院;冶金工业部钢铁研究总院;冶金工业部钢铁研究总院;冶金工业部钢铁研究总院;冶金工业部钢铁研究总院;冶金工业部钢铁研究总院;冶金工业部钢铁研究总院;冶金工业部钢铁研究总院;冶金工业部钢铁研究总院

INFLUENCE OF Cr ON "SOFTENING EFFECT" OF 30CrNiSMoV STEEL

Lu Zaojun; Wu Baorong; Wu Peizhi; Li Guiyen; Wang Qi; Lu Hongxiu; Li Xueyuan; Jin Qingqian; Wang Degen (Central Iron and Steel Research Institute; Ministry of Metallurgical Industry; Beijing)

鲁肇俊;吴宝榕;吴佩芝;李桂芬;王琪;卢鸿修;李雪缘;金钦乾;汪德根. Cr含量对30CrNi5MoV钢“软化”效应的探讨[J]. 金属学报, 1982, 18(1): 85-134.
, , , , , , , , . INFLUENCE OF Cr ON "SOFTENING EFFECT" OF 30CrNiSMoV STEEL[J]. Acta Metall Sin, 1982, 18(1): 85-134.

摘要 参考文献 相关文章 Metrics 全文: PDF(1472 KB)   摘要: Cr强烈地引起30CrNi5MoV钢的“软化”,在相同的试验条件下,随着Cr含量的增加(0.22—1.61％Cr),钢的条件比例极限(σP_(50))呈直线下降的趋势。用光学显徽镜、透射电镜和相分析等方法研究了这种“软化”效应。结果表明,“软化”主要是由于Cr改变溶质原子在α-Fe中的溶解度、粗化马氏体的亚结构及降低碳化物的长度与碳化物间距的比值从而降低σp_(50)的结果。 Abstract：The influence of Cr contents on the softening effect of steel 30CrNi5MoV was investigated by using optical microscopy, TEM and phase analysis. The conditional proportion limit, σ_p_(50), of the steel falls sharply as the increasing of Cr contents in the range 0.22—1.61％ under same other experimental conditions. It was deduced that its falling rate is expressed as: σ_p_(50)=1352—245×Cr％. The softening effect may be substantially resulted from that Cr changes the solubility of solute in α-ferrite, coarsens the martensitic substructure and reduces the ratio of the grain size of carbides to their interparticle spacings. 收稿日期: 1982-01-18      服务 把本文推荐给朋友 加入引用管理器 E-mail Alert RSS 作者相关文章 鲁肇俊 吴宝榕 吴佩芝 李桂芬 王琪 卢鸿修 李雪缘 金钦乾 汪德根 44.8K 链接本文: https://www.ams.org.cn/CN/      或      https://www.ams.org.cn/CN/Y1982/V18/I1/85 1 Lacy, C. E.; Gensamer, M., Trans. ASM, 32 (1944) , 88． 2 Leslie, W. C.; Sober, R. J.; Babcock, S. G.; Green, S. J., ASM Trans. Q., 62 (1969) , 691． 3 Leslie, W. C., Metall. Trans., 3 (1972) , 5． 4 Tanaka, T.; Watanabe, S., Acta Metall., 19 (1971) , 991． 5 Ulitchny, M. G.; Vasndevan, A. K.; Gibala, R., The Microstructure and Design of Alloys, Proc. 3rd Int. Conf. on the Strength of Metals and Alloys, Vol. 1, Cambridge, England, 1973, p. 505． 6 Spitzig, W. A.; Leslie, W. C., Acta Metall., 19 (1971) , 1143． 7 Spitzig, W. A., Mater. Sci. Eng., 16 (1974) , 169． 8 Kelley, M. J.; Stoloff, N. S., Metall. Trans., 7A (1976) , 331． 9 Thomas. G., Iron Steel Int., 46 (1973) . 451． 10 小林泽;白沢秀则;自在丸二郎,铁钢,66(1980) ,685． 11 Ansell,G.S.未发表资料;1979． 12 Bush, M. E.; Kelly, P. M., Acta Metall., 19 (1971) , 1363． 13 Bergstroem, Y.; Josefsson, ■., Scan. J. Metall., 3 (1974) , 259． 14 Norstroem, L.-■., Scan, J. Metall., 5 (1976) , 41． 15 Smith, D. W.; Hehemarm, R. F., J. Iron Steel Inst., 209 (1971) , 476． 16 Naylor, J. P., Metall. Trans., 10A (1979) , 861． 17 Irvine, K. J.; Pickering, F. B., J. Iron Steel Inst., 201 (1963) , 944．L No related articles found! Viewed Full text Abstract Cited   Shared      Discussed