Received date: 2009-06-08
Revised date: 2009-12-03
Online published: 2010-02-10
High velocity compaction (HVC) is a recently developed technology for forming high density metallic parts with high efficiency, whose densification is realized through the strong impact wave generated by liquid–pressure controlled by heavy hamper. This technology is thought to have an excellent balance between properties and cost and has several advantages over other existing forming technologies, including high and homogeneous green density, low cost, low springback and high precision. It is extremely competitive to prepare powder metallurgy parts with high density, high strength, high precision and low cost. With a high hardening rate, Ti powder is difficult to be formed through traditional pressing methods, although advanced forming methods are effective for increasing its density, such as hot–pressing and isothermal–statistic pressing, they are very expensive. HVC would thus be highly attractive to solve these problems of low density and high cost in forming Ti powder. In this paper, the process of HVC forming Ti powder was studied. Two kinds of samples, the rings with 60 mm outer and 30 mm inner diameters and the cylindricals with 20 mm diameter were prepared through HVC, respectively. The influences of impact energy and filling weight on the green density were investigated. The results show that, for the ring samples, the maximum of green density is 4.00 g/cm3 and its relative density is 88.9% at an impact energy of 3.804 kJ. However, for the cylindrical samples, the maximum of green density is 4.38 g/cm3 and its relative density is 97.4% at an impact energy of 1.217 kJ. For the both kinds of samples, the green density increases with increasing impact energy while decreases with increasing filling weight. Impact energy per weight is helpful to characterize the green density obtained at different dimension, impact energy and filling weight.
YAN Zhi-Qiao , CHEN Feng , SA Yi-Xiang , CUI Liang . HIGH VELOCITY COMPACTION AND CHARACTERISTICS OF Ti POWDER[J]. Acta Metall Sin, 2010 , 46(2) : 227 -232 . DOI: 10.3724/SP.J.1037.2009.00383
[1] Caroline E. Met Powder Rep, 2001; 56: 6
[2] Orban P L. Rom Rep Phys, 2004; 56: 505
[3] Skoglund P. Powder Metall, 2001; 44: 15
[4] Jonsen P, Haggblad H A, Troive L, Furuberg J, Allroth S, Skoglund P. Mater Sci Forum, 2007; 534–536: 289
[5] Eriksson M, Andersson M, Adolfsson E, Carlstrom E. Powder Metall, 2006; 49: 70
[6] Eriksson M, Haggblad H A, Berggren C, Andersson M, Holmersson R, Carlstrom E. Powder Metall, 2004; 47: 335
[7] Souriou D, Goeuriot P, Bonnefoy O, Thomas G, Drapier S, Bourdin S, Lazzarotto L. Adv Sci Technol, 2006; 45: 893
[8] Azhdar B, Stenberg B, Kari L. Polym Test, 2006; 25: 114
[9] Jauffr`es D, Lame O, Vigier G, Dor´e F. Polymer, 2007; 48: 6374
[10] Grinder O, Tengzelius J. Int J Powder Metall, 2008; 44: 41
[11] Wang J Z, Qu X H, Yin H Q, Zhou S Y, Yi M J. Trans Nonferrous Met Soc China, 2008; 18: 1498
(王建忠, 曲选辉, 尹海清, 周晟宇, 易明军. 中国有色金属学报, 2008; 18: 1498)
[12] Wang J Z, Qu X H, Yin H Q, Zhou S Y. Chin J Mater Res, 2008; 22: 589
(王建忠, 曲选辉, 尹海清, 周晟宇. 材料研究学报, 2008; 22: 589)
[13] Wang J Z, Qu X H, Yin H Q, Yi M J, Yuan X J. Powder Technol, 2009; 192: 131
[14] Guo S J, Chi Y, Meng F, Yang X. Mater Sci Eng Powder Metall, 2006; 11: 24
(果世驹, 迟悦, 孟飞, 杨霞. 粉末冶金材料科学与工程, 2006; 11: 24)
[15] Saito T, Takamiya H, Furuta T. Mater Sci Eng, 1998; A243: 273
[16] Chen Z H. Modern Powder Metallurgy Technique. Beijing: Chemical Industry Press, 2007: 322
(陈振华. 现代粉末冶金技术. 北京: 化学工业出版社, 2007: 322)
[17] Huang P Y. Powder Metallurgy Principle. 2nd Ed., Beijing: Metallurgical Industry Press, 1997: 173
(黄培云. 粉末冶金原理(第2版). 北京: 冶金工业出版社, 1997: 173)
[18] Sethi G, Hauck E, German R M. Mater Sci Technol, 2006; 22: 955
[19] Skoglund P, Kejzelman M, Hauer I. Met Powder Rep,2002; 57: 26
/
| 〈 |
|
〉 |
