超音速微粒轰击诱导表面纳米化对300M钢腐蚀疲劳行为的影响
收稿日期: 2022-06-15
修回日期: 2022-12-26
网络出版日期: 2023-01-10
基金资助
国家自然科学基金项目(U1804146);国家自然科学基金项目(52111530068);河南省外专引智计划项目(HNGD2020009)
Effect of Surface Nanocrystallization Induced by Supersonic Fine Particles Bombardment on Corrosion Fatigue Behavior of 300M Steel
Received date: 2022-06-15
Revised date: 2022-12-26
Online published: 2023-01-10
Supported by
National Natural Science Foundation of China(U1804146);National Natural Science Foundation of China(52111530068);Foreign Experts Introduction Project of Henan Province(HNGD2020009)
300M钢因其具有超高强度和优异塑韧性，常作为起落架的首选材料。但其在“高温、高湿、高盐”的海洋服役环境下易发生腐蚀疲劳失效，而表面强化可以有效提高其抗腐蚀疲劳性能。本工作采用超音速微粒轰击(SFPB)技术对300M超高强度钢进行表面纳米化处理，系统研究了SFPB对300M钢在3.5%NaCl溶液中的腐蚀疲劳行为的影响规律，并对300M钢腐蚀疲劳后的表面形貌、微观组织演变和残余应力松弛进行表征。结果表明，300M钢经SFPB后表层晶粒细化至纳米级，形成梯度纳米结构的同时还存在着高幅值残余压应力。在相同的加载应力水平下，SFPB有效提高了300M钢的腐蚀疲劳寿命。腐蚀疲劳后300M钢表层晶粒尺寸仍处于纳米量级，加载应力水平的增加使次表层位错密度显著增加的同时形变孪晶数量增多。在腐蚀疲劳过程中，300M钢表层由于SFPB诱导产生的残余压应力发生不同程度的松弛现象，残余应力松弛程度随着加载应力水平的增加而明显增加。
熊毅 , 栾泽伟 , 马云飞 , 厉勇 , 查小琴 . 超音速微粒轰击诱导表面纳米化对300M钢腐蚀疲劳行为的影响[J]. 金属学报, 2024 , 60(5) : 627 -638 . DOI: 10.11900/0412.1961.2022.00295
Although 300M steel is one of the preferred materials for aircraft landing gears and other key load-bearing components in aviation because of its ultra-high strength and excellent ductility, its susceptibility to corrosion fatigue fracture during service in “high temperature, high humidity, and high salt” marine environments is a significant safety hazard. Surface strengthening can effectively improve the corrosion fatigue resistance of materials, thereby improving the reliability of components and extending their service life. Hence, the surface nanocrystallization of 300M ultra-high strength steel via supersonic fine particle bombardment (SFPB) and its effect on the corrosion fatigue behavior of the material in 3.5%NaCl solution was systematically investigated and the surface morphology, microstructure evolution, and residual stress relaxation of 300M steel after corrosion fatigue were characterized. After SFPB, the grain size near the surface was observed to have reduced to the nanoscale, forming gradient nanostructures and high amplitude residual compressive stress. The SFPB treatment effectively improved the corrosion fatigue life of 300M steel at the same loading-stress level. After corrosion fatigue, the grain size of the SFPB-treated 300M steel remained at the nanoscale near the surface, and the increase in the loading stress level caused a significant increase in the dislocation density in the subsurface layer and the number of deformation twins. During the corrosion fatigue loading, the residual compressive stress induced by SFPB in the surface layer of 300M steel relaxed to various degrees, with the degree of residual stress relaxation being significantly higher for higher loading stress levels.
| 1 | Zhang S S, Li M Q, Liu Y G, et al. The growth behavior of austenite grain in the heating process of 300M steel[J]. Mater. Sci. Eng., 2011, A528: 4967 |
| 2 | Skubisz P, Sinczak J. Properties of direct-quenched aircraft forged component made of ultrahigh-strength steel 300M[J]. Aircr. Eng. Aerosp. Technol., 2018, 90: 713 |
| 3 | Mu Z T, Tan X M, Liu Z G. Corrosion damage failure law analysis and corrosion control for naval aircraft in servicing[J]. Equip. Environ. Eng., 2009, 6(1): 43 |
| 穆志韬, 谭晓明, 刘志国. 海军现役飞机的腐蚀损伤失效分析及腐蚀防护[J]. 装备环境工程, 2009, 6(1): 43 | |
| 4 | Ebara R, Fukushima Y, Nakagawa S, et al. Nitriding effect on corrosion fatigue strength of low alloy steel in 1% HCl aqueous solution[J]. Adv. Mater. Res., 2014, 891-892: 674 |
| 5 | Bag A, Lévesque M, Brochu M. Effect of shot peening on short crack propagation in 300M steel[J]. Int. J. Fatigue, 2020, 131: 105346 |
| 6 | Zhao W D, Liu D X, Zhang X H, et al. Improving the fretting and corrosion fatigue performance of 300M ultra-high strength steel using the ultrasonic surface rolling process[J]. Int. J. Fatigue, 2019, 121: 30 |
| 7 | Zhao W D, Liu D X, Zhang X H, et al. The effect of electropulsing-assisted ultrasonic nanocrystal surface modification on the microstructure and properties of 300M steel[J]. Surf. Coat. Technol., 2020, 397: 125994 |
| 8 | Zhao W D, Liu D X, Liu J, et al. The effects of laser-assisted ultrasonic nanocrystal surface modification on the microstructure and mechanical properties of 300M steel[J]. Adv. Eng. Mater., 2021, 23: 2001203 |
| 9 | Dang J Q, Zhang H, An Q L, et al. Surface integrity and wear behavior of 300M steel subjected to ultrasonic surface rolling process[J]. Surf. Coat. Technol., 2021, 421: 127380 |
| 10 | Dang J Q, An Q L, Lian G H, et al. Surface modification and its effect on the tensile and fatigue properties of 300M steel subjected to ultrasonic surface rolling process[J]. Surf. Coat. Technol., 2021, 422: 127566 |
| 11 | Wu Y H. Strengthen experimental study of high strength steel 40CrNi2Si2MoVA based on laser shock processing[J]. Adv. Mater. Res., 2013, 774-776: 1122 |
| 12 | Pistochini T E, Hill M R. Effect of laser peening on fatigue performance in 300M steel[J]. Fatigue Fract. Eng. Mater. Struct., 2011, 34: 521 |
| 13 | Zhang H P, Cai Z Y, Chi J X, et al. Microstructural evolution, mechanical behaviors and strengthening mechanism of 300M steel subjected to multi-pass laser shock peening[J]. Opt. Laser Technol., 2022, 148: 107726 |
| 14 | Xiong T Y, Liu Z W, Li Z C, et al. Supersonic fine particles bombarding: A novel surface nanocrystallization technology[J]. Mater. Rev., 2003, 17(3): 69 |
| 熊天英, 刘志文, 李智超 等. 超音速微粒轰击金属表面纳米化新技术[J]. 材料导报, 2003, 17(3): 69 | |
| 15 | Li H M, Li M Q, Liu Y G, et al. Research progress in nanocrystalline microstructure, mechanical properties and nanocrystallization mechanism of titanium alloys via surface mechanical treatment[J]. Chin. J. Nonferrous Met., 2015, 25: 641 |
| 李慧敏, 李淼泉, 刘印刚 等. 钛合金表层机械处理的纳米化组织、力学性能与机理研究进展[J]. 中国有色金属学报, 2015, 25: 642 | |
| 16 | Zhou T, Xiong Y, Chen Z G, et al. Effect of surface nano-crystallization induced by supersonic fine particles bombarding on microstructure and mechanical properties of 300M steel[J]. Surf. Coat. Technol., 2021, 421: 127381 |
| 17 | Ma Y F, Xiong Y, Chen Z G, et al. Microstructure evolution and properties of gradient nanostructures subjected to laser shock processing in 300M ultrahigh-strength steel[J]. Steel Res. Int., 2022, 93: 2100434 |
| 18 | Zhang Y X, Yang J H, Ge L L, et al. Research on mechanism of surface nanocrystalline layer in 2219 Al alloy induced by supersonic fine particles bombarding[J]. Int. J. Eng. Res. Afr., 2016, 24: 1 |
| 19 | Zhang L Y, Ma A B, Jiang J H, et al. Electrochemical corrosion properties of the surface layer produced by supersonic fine-particles bombarding on low-carbon steel[J]. Surf. Coat. Technol., 2013, 232: 412 |
| 20 | Wang Z, Wang J G, Chen Z Y, et al. Effect of Ce addition on modifying the microstructure and achieving a high elongation with a relatively high strength of as-extruded AZ80 magnesium alloy[J]. Materials, 2018, 12: 76 |
| 21 | Liu H B, Wei X X, Xing S L, et al. Effect of stress shot peening on the residual stress field and microstructure of nanostructured Mg-8Gd-3Y alloy[J]. J. Mater. Res. Technol., 2021, 10: 74 |
| 22 | Liu C S, Liu D X, Zhang X H, et al. Improving fatigue performance of Ti-6Al-4V alloy via ultrasonic surface rolling process[J]. J. Mater. Sci. Technol., 2019, 35: 1555 |
| 23 | Kim J C, Cheong S K, Noguchi H. Residual stress relaxation and low- and high-cycle fatigue behavior of shot-peened medium-carbon steel[J]. Int. J. Fatigue, 2013, 56: 114 |
| 24 | Xu X C, Liu D X, Zhang X H, et al. Mechanical and corrosion fatigue behaviors of gradient structured 7B50-T7751 aluminum alloy processed via ultrasonic surface rolling[J]. J. Mater. Sci. Technol., 2020, 40: 88 |
| 25 | Huang H W, Wang Z B, Liu L, et al. Formation of a gradient nanostructured surface layer on a martensitic stainless steel and its effects on the electrochemical corrosion behavior[J]. Acta Metall. Sin., 2015, 51: 513 |
| 黄海威, 王镇波, 刘 莉 等. 马氏体不锈钢上梯度纳米结构表层的形成及其对电化学腐蚀行为的影响[J]. 金属学报, 2015, 51: 513 | |
| 26 | Yue Y, Dai L Y, Zhong H, et al. Effect of microstructure on high cycle fatigue behavior of Ti-20Zr-6.5Al-4V alloy[J]. J. Alloys Compd., 2017, 696: 663 |
| 27 | Chen Y N, Xiong Y, Fan M X, et al. Fatigue fracture analysis of TC11 titanium alloy at different temperatures[J]. Trans. Mater. Heat Treat., 2019, 40(8): 61 |
| 陈艳娜, 熊 毅, 范梅香 等. TC11钛合金在不同温度下的疲劳断裂分析[J]. 材料热处理学报, 2019, 40(8): 61 | |
| 28 | Pandey V, Singh J K, Chattopadhyay K, et al. Influence of ultrasonic shot peening on corrosion behavior of 7075 aluminum alloy[J]. J. Alloys Compd., 2017, 723: 826 |
| 29 | Brandstetter S, Derlet P M, Van Petegem S, et al. Williamson-Hall anisotropy in nanocrystalline metals: X-ray diffraction experiments and atomistic simulations[J]. Acta Mater., 2008, 56: 165 |
| 30 | Markmann J, Yamakov V, Weissmüller J. Validating grain size analysis from X-ray line broadening: A virtual experiment[J]. Scr. Mater., 2008, 59: 15 |
| 31 | Wu Y L, Xiong Y, Liu W, et al. Effect of supersonic fine particle bombardment on microstructure and fatigue properties of Ti-6.5Al-3.5Mo-1.5Zr-0.3Si titanium alloy at different temperatures[J]. Surf. Coat. Technol., 2021, 421: 127473 |
| 32 | Chen Z G, Wu Y L, Xue Q X, et al. Effect of laser shock peening on microstructure and properties of TC11 titanium alloy with lamellar microstructure[J]. Surf. Technol., 2022, 51(7): 343 |
| 陈正阁, 武永丽, 薛全喜 等. 激光冲击强化对片层TC11钛合金组织和性能的影响[J]. 表面技术, 2022, 51(7): 343 | |
| 33 | Gao Y K, Yao M, Yang O X, et al. Influence of carburization followed by shot peening on fatigue property of 20CrMnTi steel[J]. J. Mater. Eng. Perform., 2005, 14: 591 |
| 34 | Zhao H S, Chen G Q, Gai P T, et al. Residual stress relaxation and re-shot-peening process of wet shot-peened titanium alloy during tensile fatigue load[J]. J. Mater. Eng., 2020, 48(5): 136 |
| 赵慧生, 陈国清, 盖鹏涛 等. 拉-拉疲劳载荷下钛合金湿喷丸的残余应力松弛及再次喷丸工艺[J]. 材料工程, 2020, 48(5): 136 | |
| 35 | Prabhakaran S, Kulkarni A, Vasanth G, et al. Laser shock peening without coating induced residual stress distribution, wettability characteristics and enhanced pitting corrosion resistance of austenitic stainless steel[J]. Appl. Surf. Sci., 2018, 428: 17 |
| 36 | Kou Y, Du Y L. Effects of laser shock peening on corrosion fatigue behavior of 2Cr13 stainless steel[J]. IOP Conf. Ser. Mater. Sci. Eng., 2018, 452: 022014 |
| 37 | Liu D, Liu D X, Zhang X H, et al. Surface nanocrystallization of 17-4 precipitation-hardening stainless steel subjected to ultrasonic surface rolling process[J]. Mater. Sci. Eng., 2018, A726: 69 |
| 38 | Huang H W, Wang Z B, Lu J, et al. Fatigue behaviors of AISI 316L stainless steel with a gradient nanostructured surface layer[J]. Acta Mater., 2015, 87: 150 |
| 39 | Gangloff R P, Ives M B. Environment-Induced Cracking of Metals[M]. Wisconsin, USA: Elsevier, 1990: 55 |
| 40 | Müller M. Theoretical considerations on corrosion fatigue crack initiation[J]. Metall. Trans., 1982, 13A: 649 |
| 41 | Schnubel D, Huber N. The influence of crack face contact on the prediction of fatigue crack propagation in residual stress fields[J]. Eng. Fract. Mech., 2012, 84: 15 |
| 42 | Lu J Z, Qi H, Luo K Y, et al. Corrosion behaviour of AISI 304 stainless steel subjected to massive laser shock peening impacts with different pulse energies[J]. Corros. Sci., 2014, 80: 53 |
| 43 | Starker P, Wohlfahrt H, Macherauch E. Subsurface crack initiation during fatigue as a result of residual stresses[J]. Fatigue Fract. Eng. Mater. Struct., 1979, 1: 319 |
| 44 | Zhang C H, Hu K, Zheng M, et al. Effect of surface nanocrystallization on fatigue properties of Ti-6Al-4V alloys with bimodal and lamellar structure[J]. Mater. Sci. Eng., 2021, A813: 141142 |
/
| 〈 |
|
〉 |
