镍基单晶高温合金再结晶过程模拟研究

吴春龙; 许庆彦; 熊继春; 李忠林; 李嘉荣; 柳百成

doi:10.3724/SP.J.1037.2013.00036

金属学报 >

2013 , Vol. 49 >Issue 5: 523 - 529

DOI: https://doi.org/10.3724/SP.J.1037.2013.00036

论文

镍基单晶高温合金再结晶过程模拟研究

吴春龙 ,
许庆彦 ,
熊继春 ,
李忠林 ,
李嘉荣 ,
柳百成

展开

1) 清华大学材料学院, 先进成形制造教育部重点实验室, 北京 100084
2) 北京航空材料研究院先进高温结构材料重点实验室, 北京 100095

吴春龙, 男, 1987年生, 硕士生

收稿日期: 2013-01-21

修回日期: 2013-03-10

网络出版日期: 2013-05-11

基金资助

国家重点基础研究发展计划项目2011CB706801, 国家自然科学基金项目51171089, 以及国家科技重大专项项目

收起

NUMERICAL SIMULATION OF RECRYSTALLIZATION PROCESS OF NICKEL BASE SINGLE CRYSTAL SUPERALLOY

WU Chunlong ,
XU Qingyan ,
XIONG Jichun ,
LI Zhonglin ,
LI Jiarong ,
LIU Baicheng

Expand

1) School of Materials Science and Engineering, Key Laboratory for Advanced Materials Processing Technology, Ministry of Education, Tsinghua University, Beijing 100084
2) Science and Technology on Advanced High Temperature Structural Materials Laboratory, Beijing Institute of Aeronautical Materials, Beijing 100095

Received date: 2013-01-21

Revised date: 2013-03-10

Online published: 2013-05-11

Fold

摘要

结合单晶高温合金各向异性的特点, 建立了基于应力应变和变形储存能的物理数学模型, 考虑了再结晶晶界迁移引起的晶粒长大过程. 针对单晶高温合金变形过程进行应力应变模拟, 考虑了不均匀变形对再结晶的影响, 计算储存能分布, 建立了再结晶临界储存能模型, 模拟了镍基单晶高温合金在局部变形后热处理过程发生的静态再结晶过程. 对DD6单晶高温合金试样表面进行冷变形处理, 分别置于1280 ℃温度下进行不同时间的热处理, 样品冷变形区域表面发生了不同程度的再结晶, 并且随着时间延长, 再结晶区域和晶粒尺寸逐渐增加. 通过2D数值模拟方法研究这一过程, 并将再结晶组织模拟结果与EBSD实验结果进行对比, 结果吻合较好, 表明借助于该模型能较好地模拟单晶高温合金的再结晶过程.

关键词： 单晶高温合金; 再结晶; 应力和变形; 数值模拟

本文引用格式

吴春龙 , 许庆彦 , 熊继春 , 李忠林 , 李嘉荣 , 柳百成 . 镍基单晶高温合金再结晶过程模拟研究[J]. 金属学报, 2013 , 49(5) : 523 -529 . DOI: 10.3724/SP.J.1037.2013.00036

Abstract

The formation of recrystallization can cause great damage on the performance of nickel base single crystal superalloy turbine blade. The stress, strain and stored energy distribution of single crystal superalloy were modeled and simulated under the condition of inhomogeneous deformation. The critical stored energy was established which takes the anisotropic mechanical properties of single crystal superalloy and the recrystallization grain boundary migration process into account. Based on the calculation of the critical stored energy, the recrystallization microstructure in the local deformation zone after heat treatment was simulated by using cellular automaton (CA) method. DD6 single crystal test bars were treated by the cold deformation process and then annealed at the temperature of 1280 ℃ for 30, 60 and 240 min. The experimental results showed that the recrystallization occurred on the surface near the deformation area. The recrystallization area and the grain size increased gradually with time. The simulated microstructure results agree well with the experimental ones (EBSD) and indicate that the recrystallization process of single crystal superalloy can be well simulated by the proposed model.

Key words： single crystal superalloy; recrystallization; stress and deformation; numerical simulation

参考文献

[1] Schafrik R, Sprague R. Adv Mater Processes, 2004; 162(5): 29

[2] Reed R C. The Superalloys: Fundamentals and Applications. Cambridge: Cambridge University Press, 2006: 1

[3] Zambaldi C, Roters F, Raabe D, Glatzel U. Mater Sci Eng, 2007; A454-455: 433

[4] Zhang Y Q, Jiang S Y, Liang Y L, Hu L. Comput Mater Sci, 2013; 71: 124

[5] Janssens K G F. Modell Simul Mater Sci Eng, 2003; 11: 157

[6] Hesselbarth H W, Gobel I R. Acta Metall Mater, 1991; 39: 2135

[7] Yazdipour N, Davies C H J, Hodgson P D. Comput Mater Sci, 2008; 44: 566

[8] Marx V, Reher F R, Gottstein G. Acta Mater, 1999; 47: 1219

[9] Panwisawas P, Mathur H, Gebelin J C, Putman C, Rae C M F, Reed R C. Acta Mater, 2012; 61: 51

[10] Xiong J C, Li J R, Liu S Z, Han M. Chin J Nonferrous Met, 2010; 7: 1328

(熊继春, 李嘉荣, 刘世忠, 韩梅. 中国有色金属学报, 2010; 7: 1328)

[11] Takaki T, Tomita Y. Int J Mech Sci, 2010; 52: 320

[12] Mohamed G, Bacroix B. Acta Mater, 2000; 48: 3295

[13] Xiong J C, Li J R, Liu S Z, Zhao J Q, Han M. Mater Charact, 2010; 61: 749

[14] Li J R, Xiong J C, Tang D Z. Advanced High Temperature Structural Materials and Technology.Beijing: National Defense Industry Press, 2012: 177

(李嘉荣, 熊继春, 唐定中. 先进高温结构材料与技术. 北京: 国防工业出版社, 2012: 177)

[15] Schafer C, Mohles V, Gottstein G. Acta Mater, 2011; 59: 6574

[16] Zheng C W, Lan Y J, Xiao N M, Li D Z, Li Y Y. Acta Metall Sin, 2006; 42: 474

(郑成武, 兰永军, 肖纳敏, 李殿中, 李依依. 金属学报, 2006; 42: 474)

[17] Zhou S Y. Shanghai Met (Nonferrous Fasc), 1991; 12(2): 50

(周善佑. 上海金属(有色分册), 1991; 12(2): 50)

[18] Raabe D, Becker R C. Modell Simul Mater Sci Eng, 2000; 8: 445

[19] Zhang Y B, Godfrey A, Jensen D J. Scr Mater, 2011; 64: 331

[20] Pan D. PhD Dissertation, Tsinghua University, Beijing, 2010

(潘冬. 清华大学博士学位论文, 北京, 2010)

[21] Li J R, Zhao J Q, Liu S Z, Han M. In: Reed R C, Green K A, Caron P, Gabb T P, Fahrmann M G,Huron E S eds., Proc 11th Int Symposium on Superalloys. Champion, PA: Minerals,Metals & Materials Soc, 2008: 443

[22] Yu Q M. Master Thesis, Northwestern Polytechnical University, Xi'an, 2005

(于庆民. 西北工业大学硕士学位论文, 西安, 2005)

[23] Li C. Theory of Metals. Harbin: Harbin Institute of Technology Press, 1996: 298

(李超. 金属学原理. 哈尔滨: 哈尔滨工业大学出版社, 1996: 298)

[24] Ye W P, Gall R L, Saindrenan G.Mater Sci Eng, 2002; A332: 41

[25] Radhakrishnan B, Sarma G B, Zacharia T.Acta Mater, 1998; 46: 4415

Options

文章导航

模态框（Modal）标题

摘要

本文引用格式

Abstract

参考文献