Please wait a minute...
金属学报    DOI: 10.11900/0412.1961.2026.00208
  本期目录 | 过刊浏览 |
电弧功率-焊接速率协同调控7075-Sc铝合金CMT+P接头组织特征及力学性能
李亚杰, 王中熙, 秦凤明, 赵晓东, 苟晓滨, 梁上上
太原科技大学材料科学与工程学院  太原  030024
Effects of Arc Power and Welding Speed Variations on Microstructural Characteristics and Mechanical Properties of CMT+P-Welded Sc-Modified 7075 Aluminum Alloy Joints
LI Yajie, WANG Zhongxi, QIN Fengming, ZHAO Xiaodong, GOU Xiaobin, LIANG Shangshang

School of Materials Science and Engineering, Taiyuan University of Science and Technology, Taiyuan 030024, China

引用本文:

李亚杰, 王中熙, 秦凤明, 赵晓东, 苟晓滨, 梁上上. 电弧功率-焊接速率协同调控7075-Sc铝合金CMT+P接头组织特征及力学性能[J]. 金属学报, DOI: 10.11900/0412.1961.2026.00208.

全文: PDF(6832 KB)  
摘要: 7xxx系高强铝合金焊接过程中易产生气孔、晶界脆性第二相及热影响区软化,其组织与缺陷对焊接热过程高度敏感,导致接头强度与塑性难以兼顾。为明确CMT+P工艺参数对上述组织与缺陷及接头强塑性的影响,采用含0.25 wt.% Sc的7075焊丝对2 mm厚7075铝合金薄板进行冷金属过渡脉冲(CMT+P)焊接,借助OM、EBSD、SEM-EDS、TEM表征方法及力学测试研究关键工艺参数匹配对熔合线附近组织、缺陷及力学性能的影响。结果表明,接头组织和性能随电弧功率升高、热输入降低呈非单调变化。高热输入–低功率焊接条件下,接头孔隙率最低,为0.65%±0.07%,晶粒分布均匀,脆性第二相T-AlZnMgCu在晶界断续分布,屈服强度、抗拉强度和断后伸长率分别为247.7 MPa、349.7 MPa和3.6%。在中间参数区间,焊缝的孔隙率升高、混晶加剧及晶界第二相连续分布,力学性能下降。进一步降低热输入并提高电弧功率后,孔隙率和晶界第二相连续性均有所降低,结合熔池流动特征推测,较高电弧功率可能增强液态金属流动,从而有利于气泡迁移和溶质重新分布,使接头性能得到部分恢复。
关键词 : 7xxx系铝合金,  CMT+P 焊接,  Sc改性,  晶界第二相,  强塑性匹配    
Abstract:
Fusion welding of high-strength 7xxx-series aluminum alloys is prone to porosity, brittle grain-boundary secondary phases, and softening in the heat-affected zone. Their microstructures and defects are highly sensitive to the welding thermal cycle, making it difficult to achieve a satisfactory balance between strength and ductility. To clarify the effects of CMT+P process parameters on these microstructural features, defects, and the strength–ductility balance of the joints, 2-mm-thick 7075 aluminum alloy sheets were welded by cold metal transfer plus pulse (CMT+P) using a 7075 filler wire containing 0.25 wt.% Sc. Optical microscopy (OM), electron backscatter diffraction (EBSD), scanning electron microscopy coupled with energy-dispersive spectroscopy (SEM–EDS), transmission electron microscopy (TEM), and mechanical testing were employed to investigate the effects of key process-parameter combinations on the microstructure, defects, and mechanical properties near the fusion line.The results show that the microstructure and mechanical properties of the joints exhibit a non-monotonic variation with increasing arc power and decreasing heat input. Under the high-heat-input–low-arc-power condition, the joint exhibited the lowest porosity of 0.65% ± 0.07%, a relatively uniform grain distribution, and discontinuously distributed brittle T-AlZnMgCu phases along the grain boundaries. The corresponding yield strength, ultimate tensile strength, and elongation after fracture were 247.7 MPa, 349.7 MPa, and 3.6%, respectively. Within the intermediate parameter range, increased porosity, aggravated mixed-grain structures, and the continuous distribution of grain-boundary secondary phases led to a deterioration in mechanical properties. With a further decrease in heat input and an increase in arc power, both the porosity and the continuity of grain-boundary secondary phases were reduced. Based on the characteristics of molten-pool flow, it is inferred that the higher arc power may enhance liquid-metal flow, thereby facilitating bubble migration and solute redistribution and resulting in a partial recovery of the joint properties.
Key words: 7xxx-series aluminum alloy    CMT+P welding    Sc modification    grain-boundary secondary phase    strength–ductility balance
收稿日期: 2026-07-30     
基金资助:中央引导地方科技发展资金项目(No.YDZJSX20231A045 和 YDZJSX2024D053); 山西省基础研究计划(No.202303021212216),及太原科技大学研究生教育创新计划项目No.SJ2026049
No related articles found!