3D-SPD Rolling Method of 45 Steel Ultrafine Grained Bar with Bulk Size

doi:10.11900/0412.1961.2020.00247

Acta Metall Sin

2021, Vol. 57

Issue (5): 605-612 DOI: 10.11900/0412.1961.2020.00247

Research paper

Current Issue | Archive | Adv Search

3D-SPD Rolling Method of 45 Steel Ultrafine Grained Bar with Bulk Size

LIN Pengcheng¹^,², PANG Yuhua¹^,²(

), SUN Qi¹^,², WANG Hangduo¹^,², LIU Dong³, ZHANG Zhe³

^1.School of Metallurgical Engineering, Xi'an University of Architecture and Technology, Xi'an 710055, China
^2.Shaanxi Metallurgical Engineering Technology Research Center, Xi'an University of Architecture and Technology, Xi'an 710055, China
^3.School of Materials Science and Engineering, Northwestern Polytechnical University, Xi'an 710072, China

Cite this article:

LIN Pengcheng, PANG Yuhua, SUN Qi, WANG Hangduo, LIU Dong, ZHANG Zhe. 3D-SPD Rolling Method of 45 Steel Ultrafine Grained Bar with Bulk Size. Acta Metall Sin, 2021, 57(5): 605-612.

Download:

HTML

PDF(6823KB)
Export: BibTeX | EndNote (RIS)

Abstract

Based on the limitations of severe plastic deformation (SPD) technology, such as a small effective deformation area and huge forming load, in the preparation of ultrafine grained/nanocrystalline materials, preparing industrial grade bulk ultrafine grained materials is difficult. In this work, a new SPD method, titled 3D-SPD, for preparing bulk ultrafine grained bars is proposed based on the cross-rolling principle. A severe torsion and compression deformation region was constructed using specially-curved conical rolls and guide plates, super large feed angles, and diameter reduction ratios. During the 3D-SPD process, a billet entered the deformation region from the large diameter side of the roll, where the deformation pressure was MPa grade and able to realize the SPD process with effective strains greater than 6.5. A crack control model based on Oyane criteria was established. Through the optimization analysis of damage factors under different deformation conditions, the crack induced by the Mannesmann effect was effectively restrained. Based on theoretical and experimental results, optimal parameters were determined as follows: cone angle 5°, feed angle 24°, diameter reduction ratio 50%, temperature 700^oC, ovality coefficient 1.02, and roll speed 40 r/min. A 25 mm-diameter ultrafine grained bar of 45 steel was obtained by the single pass deformation. The average grain size was refined from 46 μm to 1 μm, and the yield and tensile strengths were increased by 46% and 42%, respectively.

Key words: severe plastic deformation ultrafine grained bar 3D-SPD Mannesmann effect severe torsion and compression deformation region

Received: 09 July 2020

ZTFLH:

TG146.23

Fund: Key Research and Development Plan of Shaanxi Province(2020GY-253)

About author: PANG Yuhua, professor, Tel: 13186001012, E-mail: pyhyyl@126.com

	Service

	E-mail this article
	Add to citation manager
	E-mail Alert
	RSS
	（）
	Articles by authors
	Pengcheng LIN
	Yuhua PANG
	Qi SUN
	Hangduo WANG
	Dong LIU
	Zhe ZHANG

URL:

https://www.ams.org.cn/EN/10.11900/0412.1961.2020.00247 OR https://www.ams.org.cn/EN/Y2021/V57/I5/605

Fig.1 Schematics of 3D severe plastic deformation (3D-SPD) finite element model from views of front (a), left (b), and top (c) (n—roll speed, α—cone angle, β—feed angle, γ—cross angle, V_x—feeding direction)

Fig.2 Comparisons of deformation zones between 3D-SPD (a) and traditional cross-rolling (b)

Table 1 Comparisons of parameters between 3D-SPD and traditional cross-rolling^[26]

Fig.3 Calculated damage values (upper) and longitudinal section morphologies (lower) of samples fabricated by traditional cross rolling (a) and 3D-SPD (b)

Fig.4 Comparisons of equivalent strain between traditional longitudinal rolling (a) and 3D-SPD (b)

Fig.5 Comparisons of torsion angles between traditional cross rolling (a) and 3D-SPD (b)

Fig.6 Comparisons of forces (a) and torques (b) between traditional longitudinal rolling and 3D-SPD

Fig.7 Equivalent strains in 3D-SPD process (a) and changes of equivalent strain with time (b) (r—distance between tracking point and rolling line, R—bar radius)

Fig.8 Distribution of temperature in 3D-SPD process

Fig.9 Homemade 3D-SPD testing machine (a) and 45 steel bars after rolling (b)

Fig.10 Microstructures of 45 steel before (a) and after (b) rolling

Fig.11 Stress-strain curves of 45 steel before and after rolling (The inset shows the specific fracture position of the sample before and after rolling)

1	Sabbaghianrad S, Langdon T G. A critical evaluation of the processing of an aluminum 7075 alloy using a combination of ECAP and HPT [J]. Mater. Sci. Eng., 2014, A596: 52
2	Saito Y, Utsunomiya H, Tsuji N, et al. Novel ultra-high straining process for bulk materials—Development of the accumulative roll-bonding (ARB) process [J]. Acta Mater., 1999, 47: 579
3	Tsuji N, Saito Y, Utsunomiya H, et al. Ultra-fine grained bulk steel produced by accumulative roll-bonding (ARB) process [J]. Scr. Mater., 1999, 40: 795
4	Estrin Y. Extreme grain refinement by severe plastic deformation: A wealth of challenging science [J]. Acta Mater., 2013, 61: 782
5	Reshetov A, Kulagin R, Korshunov A, et al. The occurrence of ideal plastic state in CP titanium processed by twist extrusion [J]. Adv. Eng. Mater., 2018, 20: 1700899
6	Beygelzimer Y, Orlov D. Metal plasticity during the twist extrusion [J]. Defect Diffus. Forum, 2002, 208-209: 311
7	Pang Y H, Lin P C, Kang D N, et al. Equidistant screw rolling method for large-size 45 steel superfine crystal bar [P]. Chin Pat, 10172304.4, 2018
	庞玉华, 林鹏程, 康荻娜等. 一种大尺寸45钢超细晶棒材的等距螺旋轧制方法 [P]. 中国专利, 10172304.4, 2018)
8	Liu D, Pang Y H, Tao B. A 3D-SPD ultrafine grained bar forming method of F+P type non-quenched and tempered steel [P]. Chin Pat, 10809863.9, 2020
	刘东, 庞玉华, 陶镳. 一种F+P型非调质钢的3D-SPD超细晶棒材成形方法 [P]. 中国专利, 10809863.9, 2020)
9	Zhilyaev A P, Langdon T G. Using high-pressure torsion for metal processing: Fundamentals and applications [J]. Prog. Mater. Sci., 2008, 53: 893
10	Segal V M, Reznikov V I, Drobyshevskiy A E, et al. Plastic working of metals by simple shear [J]. Russ. Metall., 1981, 1: 99
11	Segal V M. Materials processing by simple shear [J]. Mater. Sci. Eng., 1995, A197: 157
12	Segal V M. Severe plastic deformation: simple shear versus pure shear [J]. Mater. Sci. Eng., 2002, A338: 331
13	Segal V M. Slip line solutions, deformation mode and loading history during equal channel angular extrusion [J]. Mater. Sci. Eng., 2003, A345: 36
14	Segal V M. Deformation mode and plastic flow in ultra fine grained metals [J]. Mater. Sci. Eng., 2005, A406: 205
15	Valiev R Z, Zhilyaev A P, Langdon T G. Bulk Nanostructured Materials: Fundamentals and Applications [M]. Hoboken: John Wiley & Sons, 2013: 191
16	Vaughan M W, Samimi P, Gibbons S L, et al. Exploring performance limits of a new martensitic high strength steel by ausforming via equal channel angular pressing [J]. Scr. Mater., 2020, 184: 63
17	Yoon S C, Seo M H, Kim H S. Preform effect on the plastic deformation behavior of workpieces in equal channel angular pressing [J]. Scr. Mater., 2006, 55: 159
18	Bridgman P W. On torsion combined with compression [J]. J. Appl. Phys., 1943, 14: 273
19	Edalati K, Daio T, Arita M, et al. High-pressure torsion of titanium at cryogenic and room temperatures: Grain size effect on allotropic phase transformations [J]. Acta Mater., 2014, 68: 207
20	Fu J, Ding H, Huang Y, et al. Influence of phase volume fraction on the grain refining of a Ti-6Al-4V alloy by high-pressure torsion [J]. J. Mater. Res., 2015, 4: 2
21	Todaka Y, Umemoto M, Yamazaki A, et al. Influence of high-pressure torsion straining conditions on microstructure evolution in commercial purity aluminum [J]. Mater. Trans., 2008, 49: 7
22	Park J, Song D H, Lee D, et al. Grain refinement of medium carbon steel with controlled thermo-mechanical deformation [A]. Ultrafine Grained Materials II [M]. Hoboken: John Wiley & Sons, Ltd, 2013: 275
23	Liu B X, Fan K Y, Yin F X, et al. Effect of caliber rolling reduction ratios on the microstructure and mechanical properties of 45 medium carbon steel [J]. Mater. Sci. Eng., 2020, A774: 138954
24	Jia N N, Guo K, He Y M, et al. A thermomechanical process to achieve mechanical properties comparable to those of quenched-tempered medium-C steel [J]. Mater. Sci. Eng., 2017, A700: 175
25	Oyane M, Sato T, Okimoto K, et al. Criteria for ductile fracture and their applications [J]. J. Mech. Working Technol., 1980, 4: 65
26	Wang T P, Qi K M. Metal Plastic Processing [M]. 2nd Ed., Beijing: Metallurgical Industry Press, 2001: 132
	王廷溥, 齐克敏. 金属塑性加工学 [M]. 第2版，北京: 冶金工业出版社, 2001: 132
27	Liu W C. Research on large-bar continuous rolling process and rolling model [J]. CFHI Technol., 2016, (5): 54
	刘万忱. 大规格棒材连轧工艺及轧制模型研究 [J]. 一重技术, 2016, (5): 54
28	Shi X S. Numerical simulation study on ultra-fine grained rod rolling of medium carbon steel [D]. Qinhuangdao: Yanshan University, 2013
	史喜帅. 中碳钢超微细晶棒材轧制数值模拟研究 [D]. 秦皇岛: 燕山大学, 2013
29	Valiev R Z, Islamgaliev R K, Alexandrov I V. Bulk nanostructured materials from severe plastic deformation [J]. Prog. Mater. Sci., 2000, 45: 103

[1]	NI Song, LIAO Xiaozhou, ZHU Yuntian. EFFECT OF SEVERE PLASTIC DEFORMATION ON THE STRUCTURE AND MECHANICAL PROPERTIES OF BULK NANOCRYSTALLINE METALS[J]. 金属学报, 2014, 50(2): 156-168.

No Suggested Reading articles found!

Viewed

Full text

Abstract

Cited

Shared

Discussed