Please wait a minute...
金属学报  2011, Vol. 47 Issue (10): 1335-1341    DOI: 10.3724/SP.J.1037.2011.00141
  论文 本期目录 | 过刊浏览 |
新型无Ni高N奥氏体不锈钢的低温变形行为
徐明舟,王建军,刘春明
东北大学材料各向异性与织构教育部重点实验室, 沈阳 110819
LOW TEMPERATURE DEFORMATION BEHAVIOR OF HIGH–NITROGEN NICKEL–FREE AUSTENITIC STAINLESS STEELS
XU Mingzhou, WANG Jianjun, LIU Chunming
Key Laboratory for Anisotropy and Texture of Materials, Ministry of Education, Northeastern University, Shenyang 110819
引用本文:

徐明舟 王建军 刘春明. 新型无Ni高N奥氏体不锈钢的低温变形行为[J]. 金属学报, 2011, 47(10): 1335-1341.
, , . LOW TEMPERATURE DEFORMATION BEHAVIOR OF HIGH–NITROGEN NICKEL–FREE AUSTENITIC STAINLESS STEELS[J]. Acta Metall Sin, 2011, 47(10): 1335-1341.

全文: PDF(1202 KB)  
摘要: 利用冲击实验、拉伸实验、XRD和TEM对2种不同N含量的无Ni高N奥氏体不锈钢低温变形行为进行了研究. 结果表明, 高N奥氏体不锈钢在低温下发生明显的韧脆转变和加工硬化现象. 在实验材料的Mn含量水平内, 提高Mn含量能够改善高N奥氏体不锈钢的低温塑性和韧性, 降低其韧脆转变温度. 18Cr-12Mn-0.55N钢在低温拉伸变形时会发生形变诱导马氏体相变, 但马氏体转变量很少,降低温度对马氏体转变量无明显影响. 形变诱导马氏体能提高高N奥氏体不锈钢的加工硬化能力, 但降低了钢的低温塑性和韧性. 加工硬化能力和层错能随温度的降低而降低是Fe-Cr-Mn高N奥氏体不锈钢在低温下发生脆断的主要原因.
关键词 高N奥氏体不锈钢 冲击韧性 力学性能 马氏体转变    
Abstract:The low–temperature deformation behaviors of two high–nitrogen nickel–free austenitic stainless steels (HNSs) with different N content were investigated by impact test, tensile test, XRD and TEM. The results indicate that HNS shows apparent ductile–to–brittle transformation (DBT) and work–hardening at low temperature. In the range of the experimental steels’ Mn content, the increase of Mn content improved the plasticity and the toughness at low temperature, and decreased the DBT temperature of HNS. Deformation–induced martensite transformation occurs in steel 18Cr–12Mn–0.55N during tensile deformation at low temperature, but the content of martensite is low and the decrease of temperature has no obvious effect on its formation. Deformation–induced martensite enhances the work–hardening ability but decreases the plasticity and toughness of HNS at low temperature. The decreases of work–hardening ability and stacking fault energy with temperature decreasing are the main reasons for brittle fracture of Fe–Cr–Mn HNS at low temperature.
Key wordshigh–nitrogen austenitic stainless steel    impact toughness    mechanical property    martensite transformation
收稿日期: 2011-03-17     
基金资助:

国家科技重大专项2009ZX04008-021和辽宁省科技攻关计划项目2007221007资助

作者简介: 徐明舟, 男, 1983年生, 博士生
[1] Cheng X N, Dai Q X. The Design and Control of Austenitic Stainless Steel. Beijing: National Defense IndustryPress, 2005: 3

(程晓农, 戴起勋. 奥氏体钢设计与控制. 北京: 国防工业出版社, 2005: 3)

[2] Mudali U K, Raj B, translated by Li J, Huang Y H. High Nitrogen Steels and Stainless Steels, Manufacturing, Properties and Applications. Beijing: Chemical Industry Press, 2006: 5

(Mudali U K, Raj B著, 李晶, 黄运华  译. 高氮钢和不锈钢--生产、性能与应用. 北京: 化学工业出版社, 2006: 5)

[3] Ilola R J, Hänninen H E, Ullakko K M. ISIJ Int, 1996; 36: 873

[4] Tomota Y, Endo S. ISIJ Int, 1990; 30: 656

[5] Gavriljuk V G, Sozinova A L, Foct J, Petrov J N, Polushkin Y A. Acta Mater, 1998; 46: 1157

[6] Milititsky M, Matlock D K, Regully A, Dewispelaere N, Penning J, Hanninen H. Mater Sci Eng, 2008; A496: 189

[7] Tomoto Y, Xia Y, Inoue K. Acta Mater, 1998; 46: 1577

[8] Ishizaka J, Orita K, Terao K. Tetsu Hagan´e, 1992; 78: 1846

[9] Tobler R L, Leyn D. Metall Mater Trans, 1988; 19A: 1626

[10] Ojima M, Adachi Y, Tomota Y, Ikeda K, Katada Y. J Jpn Inst Met, 2009; 73: 283

[11] Milititsky M, Matlock D K, Regully A. Mater Sci Eng, 2008; A496: 189

[12] Saller G, Hahn K S, Scheu C, Clemens H. Mater Sci Eng, 2006; A427: 246

[13] Liu S X, Liu X M, Liu R, Wang C X, Xing F. J Iron Steel Res, 2005; 17: 40

(刘树勋, 刘宪民, 刘蕤, 王春旭, 邢峰. 钢铁研究学报, 2005; 17: 40)

[14] Simmons J W. Acta Mater, 1997; 45: 2467

[15] Breedis J, Robertson W. Acta Metall, 1962; 10: 1077

[16] Lee T H, Oh C S, Kim S J. Scr Mater, 2008; 58: 110

[17] Liu S Y, Liu D Y, Liu S C. J Mater Sci, 2007; 42: 7514

[18] Cheng X N, Dai Q X. The Design and Control of Austenitic Stainless Steel. Beijing: National Defense Industry Press, 2005: 28

(程晓农, 戴起勋. 奥氏体钢设计与控制. 北京: 国防工业出版社, 2005: 28)

[19] Gavriljuk V G, Berns H. High Nitrogen Steels. Berlin: Springer, 1999: 192

[20] Kibey S, Liu J B, Curtis M J, Johnson D D, Sehitoglu H. Acta Mater, 2006; 54: 2991

[21] Hu B F, Jia C C. Acta Metall Sin, 2001; 37: 703

(胡本芙, 贾成厂. 金属学报, 2001; 37: 703)

[22] Hübner W, Pyzalla A, Assmus K, Wild E, Wroblewski T. Wear, 2003; 255: 476

[23] Gulyaev A P, Lebedev D V, Gadzhibalaev G A. Met Sci Heat Treat, 1973; 15: 1051

[24] Wang S T. PhD Thesis, Institute of Metal Research, Chinese Academy of Sciences, Shenyang, 2008

(王松涛. 中国科学院金属研究所博士学位论文, 沈阳, 2008)

[25] Byun T S, Hashimoto N, Farrell K. Acta Mater, 2004; 52:3889

[26] Wang W, Yan W, Yang K, Shan Y Y. J Mater Eng Perform,2010; 19: 1214
[1] 郑亮, 张强, 李周, 张国庆. /降氧过程对高温合金粉末表面特性和合金性能的影响:粉末存储到脱气处理[J]. 金属学报, 2023, 59(9): 1265-1278.
[2] 张雷雷, 陈晶阳, 汤鑫, 肖程波, 张明军, 杨卿. K439B铸造高温合金800℃长期时效组织与性能演变[J]. 金属学报, 2023, 59(9): 1253-1264.
[3] 宫声凯, 刘原, 耿粒伦, 茹毅, 赵文月, 裴延玲, 李树索. 涂层/高温合金界面行为及调控研究进展[J]. 金属学报, 2023, 59(9): 1097-1108.
[4] 张健, 王莉, 谢光, 王栋, 申健, 卢玉章, 黄亚奇, 李亚微. 镍基单晶高温合金的研发进展[J]. 金属学报, 2023, 59(9): 1109-1124.
[5] 李景仁, 谢东升, 张栋栋, 谢红波, 潘虎成, 任玉平, 秦高梧. 新型低合金化高强Mg-0.2Ce-0.2Ca合金挤压过程中的组织演变机理[J]. 金属学报, 2023, 59(8): 1087-1096.
[6] 陈礼清, 李兴, 赵阳, 王帅, 冯阳. 结构功能一体化高锰减振钢研究发展概况[J]. 金属学报, 2023, 59(8): 1015-1026.
[7] 丁桦, 张宇, 蔡明晖, 唐正友. 奥氏体基Fe-Mn-Al-C轻质钢的研究进展[J]. 金属学报, 2023, 59(8): 1027-1041.
[8] 袁江淮, 王振玉, 马冠水, 周广学, 程晓英, 汪爱英. Cr2AlC涂层相结构演变对力学性能的影响[J]. 金属学报, 2023, 59(7): 961-968.
[9] 吴东江, 刘德华, 张子傲, 张逸伦, 牛方勇, 马广义. 电弧增材制造2024铝合金的微观组织与力学性能[J]. 金属学报, 2023, 59(6): 767-776.
[10] 侯娟, 代斌斌, 闵师领, 刘慧, 蒋梦蕾, 杨帆. 尺寸设计对选区激光熔化304L不锈钢显微组织与性能的影响[J]. 金属学报, 2023, 59(5): 623-635.
[11] 张东阳, 张钧, 李述军, 任德春, 马英杰, 杨锐. 热处理对选区激光熔化Ti55531合金多孔材料力学性能的影响[J]. 金属学报, 2023, 59(5): 647-656.
[12] 刘满平, 薛周磊, 彭振, 陈昱林, 丁立鹏, 贾志宏. 后时效对超细晶6061铝合金微观结构与力学性能的影响[J]. 金属学报, 2023, 59(5): 657-667.
[13] 李述军, 侯文韬, 郝玉琳, 杨锐. 3D打印医用钛合金多孔材料力学性能研究进展[J]. 金属学报, 2023, 59(4): 478-488.
[14] 吴欣强, 戎利建, 谭季波, 陈胜虎, 胡小锋, 张洋鹏, 张兹瑜. Pb-Bi腐蚀Si增强型铁素体/马氏体钢和奥氏体不锈钢的研究进展[J]. 金属学报, 2023, 59(4): 502-512.
[15] 王虎, 赵琳, 彭云, 蔡啸涛, 田志凌. 激光熔化沉积TiB2 增强TiAl基合金涂层的组织及力学性能[J]. 金属学报, 2023, 59(2): 226-236.