Please wait a minute...
金属学报  2008, Vol. 44 Issue (7): 803-809     
  论文 本期目录 | 过刊浏览 |
高压扭转铜试样的微观组织与压缩性能
谢子令;武晓雷;谢季佳;洪友士
中国科学院力学研究所非线性力学国家重点实验室
Microstructures and compression properties of copper processed by high-pressure torsion
XIE Zi-Ling;Xiaolei Wu;Jijia Xie;Youshi Hong
中国科学院力学研究所
引用本文:

谢子令; 武晓雷; 谢季佳; 洪友士 . 高压扭转铜试样的微观组织与压缩性能[J]. 金属学报, 2008, 44(7): 803-809 .
, , , . Microstructures and compression properties of copper processed by high-pressure torsion[J]. Acta Metall Sin, 2008, 44(7): 803-809 .

全文: PDF(8569 KB)  
摘要: 通过高压扭转对铜试样施加不同程度的变形, 研究了样品扭转面(ND面)和纵截面(TD面)上微观组织特征. 对ND面, 在较小的剪应变下, 原始晶粒形貌模糊, 晶粒内部形成等轴状的位错胞及亚晶结构; 随变形量的增大, 亚晶 间取向差及亚晶内部的位错密度增大, 最后形成亚微米尺度的等轴晶粒. 对TD面, 变形初期原始晶粒被拉长, 晶粒内 部为位错墙分割成的层状结构, 层内为拉长的位错胞; 随变形程度的增大, 拉长晶粒的宽度减小, 与剪切方向的夹 角减小, 晶内层状组织间距减小, 并逐渐演化成拉长的亚晶组织; 进一步增大变形, 晶粒拉长痕迹消失, 变形组织 与ND面相似, 为等轴状亚微米晶粒. 压缩实验表明, 经16圈扭转后, 整个试样上的压缩性能基本均匀, σ0.2达到385 MPa, 应变率敏感性指数增大至0.021.
关键词 微观结构动态再结晶高压扭转    
Abstract:Microstructures of commercial purity copper deformed by high-pressure torsion have been examined by means of transmission electron microscopy. Observations have been carried out in two perpendicular directions, i.e. the longitudinal section and the transverse section. Microstructural observations in the longitudinal section revealed a rather different morphology of the dislocation structures from those observed in the transverse section. In the transverse section, dislocation cell structure was formed at low strains. With increasing strain, the dislocation cells continually transformed into equiaxed subgrains and finally into equiaxed grains with high angle grain boundaries due to dynamic recrystallization processes. In the longitudinal section, at low strains, extended dislocation boundaries were observed. With increasing strain, a lamellar structure was observed with some dislocation cell structured across it. The lamellar boundary misorientation as well as the misorentation between the dislocation cells increasing with shear strain. At median strains, the dislocation cells have transformed into elongated subgrains. At large strain, the subgrains transformed into individual grains and the outline of the lamellar structure disappeared. Compression test results show that an increase in yield stress ( 385MPa) and strain rate sensitivity (0.021) as compared to coarse grain copper.
Key wordscopper    microstructure    danamic recrystallization    high-pressure torsion (HPT)
收稿日期: 2007-10-22     
ZTFLH:  TG146.1  
[1]Valiev R Z,Islamgaliev R K,Alexandrov I V.Prog Mater Sci,2000;45:103
[2]Wang J T,Kang S B,Kim H W,Horita Z.J Mater Sci, 2002;37:5223
[3]Huang C X,Wang K,Wu S D,Zhang Z F,Li G Y,Li S X.Acta Mater,2006;54:655
[4]Wang K,Tao N R,Liu G,Lu J,Lu K.Acta Mater,2006; 54:5281
[5]Wu X,Tao N,Hong Y,Xu B,Lu J,Lu K.Acta Mater, 2002;50:2075
[6]Wu X L,Tao N R,Wei Q M,Jiang P,Lu J,Lu K.Acta Mater,2007;55:5768
[7]Zhilyaev A P,Oh-ishi K,Langdon T G,McNelley T R. Mater Sci En9,2005;A410-411:277
[8]Yang Z Q,Welzel U.Mater Lett,2005;59:3406
[9]Horita Z J,Langdon T G.Mater Sci Eng,2005;A410-411: 422
[10]Zhilyaev A P,Nurislamova G V,Kim B K,Bar(?) M D, Szpunar J A,Langdon T G.Acta Mater,2003;51:753
[11]Vorhauer A,Pippan R.Scr Mater,2004;51:921
[12]Huang X,Winther G,Hansen N,Hebesberger T,Vorhauer A,Pippan R,Zehetbauer M.Mater Sci Forum,2003;426- 432:2819
[13]Wang Y M,Jiao T,Ma E.Mater Traas,2003;44:1926
[14]Dalla Torre F H,Pereloma E V,Davies C H J.Acta Mater, 2006;54:1135
[15]Wang Y M,Ma E.Mater Sci Eng,2004;A375-377:46
[16]Carreker Jr R P,Hibbard Jr W R.Acta Metall,1953;1: 656
[17]Chen J,Lu L,Lu K.Scr Mater,2006;54:1913
[1] 李景仁, 谢东升, 张栋栋, 谢红波, 潘虎成, 任玉平, 秦高梧. 新型低合金化高强Mg-0.2Ce-0.2Ca合金挤压过程中的组织演变机理[J]. 金属学报, 2023, 59(8): 1087-1096.
[2] 李福林, 付锐, 白云瑞, 孟令超, 谭海兵, 钟燕, 田伟, 杜金辉, 田志凌. 初始晶粒尺寸和强化相对GH4096高温合金热变形行为和再结晶的影响[J]. 金属学报, 2023, 59(7): 855-870.
[3] 张德印, 郝旭, 贾宝瑞, 吴昊阳, 秦明礼, 曲选辉. Y2O3 含量对燃烧合成Fe-Y2O3 纳米复合粉末性能的影响[J]. 金属学报, 2023, 59(6): 757-766.
[4] 刘满平, 薛周磊, 彭振, 陈昱林, 丁立鹏, 贾志宏. 后时效对超细晶6061铝合金微观结构与力学性能的影响[J]. 金属学报, 2023, 59(5): 657-667.
[5] 陈凯旋, 李宗烜, 王自东, Demange Gilles, 陈晓华, 张佳伟, 吴雪华, Zapolsky Helena. Cu-2.0Fe合金等温处理过程中富Fe析出相的形态演变[J]. 金属学报, 2023, 59(12): 1665-1674.
[6] 娄峰, 刘轲, 刘金学, 董含武, 李淑波, 杜文博. 轧制态Mg-xZn-0.5Er合金板材组织及室温成形性能[J]. 金属学报, 2023, 59(11): 1439-1447.
[7] 杨超, 卢海洲, 马宏伟, 蔡潍锶. 选区激光熔化NiTi形状记忆合金研究进展[J]. 金属学报, 2023, 59(1): 55-74.
[8] 解磊鹏, 孙文瑶, 陈明辉, 王金龙, 王福会. 制备工艺对FGH4097高温合金微观组织与性能的影响[J]. 金属学报, 2022, 58(8): 992-1002.
[9] 张鑫, 崔博, 孙斌, 赵旭, 张欣, 刘庆锁, 董治中. Y元素对Cu-Al-Ni高温形状记忆合金性能的影响[J]. 金属学报, 2022, 58(8): 1065-1071.
[10] 吴彩虹, 冯迪, 臧千昊, 范诗春, 张豪, 李胤樹. 喷射成形AlSiCuMg合金的热变形组织演变及再结晶行为[J]. 金属学报, 2022, 58(7): 932-942.
[11] 李金富, 李伟. 铝基非晶合金的结构与非晶形成能力[J]. 金属学报, 2022, 58(4): 457-472.
[12] 任少飞, 张健杨, 张新房, 孙明月, 徐斌, 崔传勇. 新型Ni-Co基高温合金塑性变形连接中界面组织演化及愈合机制[J]. 金属学报, 2022, 58(2): 129-140.
[13] 姜伟宁, 武晓龙, 杨平, 顾新福, 解清阁. 热轧硅钢表层动态再结晶区形成规律及剪切织构特征[J]. 金属学报, 2022, 58(12): 1545-1556.
[14] 张显程, 张勇, 李晓, 王梓萌, 贺琛贇, 陆体文, 王晓坤, 贾云飞, 涂善东. 异构金属材料的设计与制造[J]. 金属学报, 2022, 58(11): 1399-1415.
[15] 马敏静, 屈银虎, 王哲, 王军, 杜丹. Ag-CuO触点材料侵蚀过程的演化动力学及力学性能[J]. 金属学报, 2022, 58(10): 1305-1315.