Please wait a minute...
金属学报  1993, Vol. 29 Issue (1): 43-48    
  论文 本期目录 | 过刊浏览 |
Ti-24Al-11Nb合金塑性和韧性的研究
王沿东;杨王玥;陈国良;朱世杰
北京科技大学;北京科技大学材料科学与工程系;副教授;北京(100083);北京科技大学;中国科学院金属所
PLASTICITY AND TOUGHNESS OF Ti-24Al-11Nb ALLOY
WNAG Yandong;YANG Wangyue;CHEN Guoliang;ZHU Shijie University of Science and Technology Beijing; Institute of Metal Research; Academia Sinica; Shenyang
引用本文:

王沿东;杨王玥;陈国良;朱世杰. Ti-24Al-11Nb合金塑性和韧性的研究[J]. 金属学报, 1993, 29(1): 43-48.
, , , . PLASTICITY AND TOUGHNESS OF Ti-24Al-11Nb ALLOY[J]. Acta Metall Sin, 1993, 29(1): 43-48.

全文: PDF(1290 KB)  
摘要: 采用三点弯曲装置研究了条状与块状两种组织的Ti—24Al—11Nb合金的室温塑性与缺口断裂韧性K_c~R。通过载荷—挠度测量确定了弯曲试验塑性的参数如最大挠度f_(max)、断裂应变ε_f及应变能密度U等;通过缺口试样确定的K_c~R。结果表明:条状和块状组织在室温下弯曲的ε_f小于8.8%时,线切割缺口试样呈脆性断裂;在弯曲时的塑性参数值相近时,条状组织的K_c~R高于块状的。同时,还讨论了缺口长度与缺口半径对K_c~R的影响。
关键词 Ti-24Al-11Nb合金金属间化合物断裂韧性三点弯曲试验    
Abstract:Room temperature plastic properties and notch fracture toughness ofTi-Al-Nb alloy with two microstructures, i. e., basketweave α_2+β and equiaxed α_2 distributed inbasketweave α_2+β respectively, were studied by means of three-point bending test. The plas-tic properties, such as fracture deflection f_(max), fracture strain ε_f and strain energy U, were de-rived from load vs cross-head displacement curves, which were measured by smooth speci-mens of 20×5×2.5 (mm), and notch fracture toughness K_c~R were decided by the same sizesamples, with the notch of 2.5 mm depth and 0.05 mm radius. The experimental resultsshowed that the notched samples of Ti-24Al-11Nb alloys fractured in brittle behaviour inspite of 8.8% fracture strain and the alloy with microstructures basketweave α_2+β has agreater fracture toughness than that with equiaxed α_2 distributed in basketweave α_2+β atthe same ductility level. The influence of the length and radius of notch on fracture toughnessis discussed also.
Key wordsplasticity    toughness    Ti-Al-Nb alloy    three-point bending test
收稿日期: 1993-01-18     
1 Reuss S, Vehoff H. Scr Metall Mater., 1990; 24: 1021
2 杨王玥,王沿东,陈国良,孙祖庆,祝东.材料科学工程与进展,待发表
3 王铮.断裂力学,南宁:广西人民出版社,1982:77
[1] 谷瑞成, 张健, 张明阳, 刘艳艳, 王绍钢, 焦大, 刘增乾, 张哲峰. 三维互穿结构SiC晶须骨架增强镁基复合材料制备及其力学性能[J]. 金属学报, 2022, 58(7): 857-867.
[2] 丁宗业, 胡侨丹, 卢温泉, 李建国. 基于同步辐射X射线成像液/固复层界面氢气泡的形核、生长演变与运动行为的原位研究[J]. 金属学报, 2022, 58(4): 567-580.
[3] 周丽君, 位松, 郭敬东, 孙方远, 王新伟, 唐大伟. 基于飞秒激光时域热反射法的微尺度Cu-Sn金属间化合物热导率研究[J]. 金属学报, 2022, 58(12): 1645-1654.
[4] 胡晨, 潘帅, 黄明欣. 高强高韧异质结构温轧TWIP[J]. 金属学报, 2022, 58(11): 1519-1526.
[5] 陈瑞润, 陈德志, 王琪, 王墅, 周哲丞, 丁宏升, 傅恒志. Nb-Si基超高温合金及其定向凝固工艺的研究进展[J]. 金属学报, 2021, 57(9): 1141-1154.
[6] 宫声凯, 尚勇, 张继, 郭喜平, 林均品, 赵希宏. 我国典型金属间化合物基高温结构材料的研究进展与应用[J]. 金属学报, 2019, 55(9): 1067-1076.
[7] 吉华,邓运来,徐红勇,郭伟强,邓建峰,范世通. 焊接线能量对5182-O/HC260YD+Z异种材料CMT搭接接头组织与性能的影响[J]. 金属学报, 2019, 55(3): 376-388.
[8] 陈丽群, 邱正琛, 于涛. Ru对NiAl[100](010)刃型位错电子结构的影响[J]. 金属学报, 2019, 55(2): 223-228.
[9] 曹丽华, 陈胤伯, 史起源, 远杰, 刘志权. 合金元素对中温Sn-Ag-Cu焊料互连组织及剪切强度的影响[J]. 金属学报, 2019, 55(12): 1606-1614.
[10] 何贤美, 童六牛, 高成, 王毅超. Nd含量对磁控溅射Si(111)/Cr/Nd-Co/Cr薄膜结构与磁性的影响[J]. 金属学报, 2019, 55(10): 1349-1358.
[11] 张敏, 慕二龙, 王晓伟, 韩挺, 罗海龙. TA1/Cu/X65复合板焊接接头微观组织及力学性能[J]. 金属学报, 2018, 54(7): 1068-1076.
[12] 康慧君, 李金玲, 王同敏, 郭景杰. 定向凝固Al-Mn-Be合金初生金属间化合物相生长行为及力学性能[J]. 金属学报, 2018, 54(5): 809-823.
[13] 李一哲, 龚宝明, 刘秀国, 王东坡, 邓彩艳. 面外拘束效应对单边缺口拉伸试样断裂韧性的影响[J]. 金属学报, 2018, 54(12): 1785-1791.
[14] 耿林, 吴昊, 崔喜平, 范国华. 基于箔材反应退火合成的TiAl基复合材料板材研究进展[J]. 金属学报, 2018, 54(11): 1625-1636.
[15] 于宣, 张志豪, 谢建新. 不同Ce含量Fe-6.5%Si合金的组织、有序结构和中温拉伸塑性[J]. 金属学报, 2017, 53(8): 927-936.