锻造过程中钢锭内部孔洞型缺陷闭合规律研究

doi:10.3724/SP.J.1037.2012.00339

金属学报

2012, Vol. 48

Issue (10): 1194-1200 DOI: 10.3724/SP.J.1037.2012.00339

论文

本期目录 | 过刊浏览

锻造过程中钢锭内部孔洞型缺陷闭合规律研究

徐斌,孙明月,李殿中

中国科学院金属研究所沈阳材料科学国家(联合)实验室, 沈阳 110016

THE VOID CLOSE BEHAVIOR OF LARGE INGOTS DURING HOT FORGING

XU Bin, SUN Mingyue, LI Dianzhong

Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016

引用本文:

徐斌孙明月李殿中. 锻造过程中钢锭内部孔洞型缺陷闭合规律研究[J]. 金属学报, 2012, 48(10): 1194-1200.
XU Bin SUN Mingyue LI Dianzhong. THE VOID CLOSE BEHAVIOR OF LARGE INGOTS DURING HOT FORGING[J]. Acta Metall Sin, 2012, 48(10): 1194-1200.

全文: PDF(1761 KB)

摘要:

对可能影响锻造过程中大型钢锭内部孔洞型缺陷闭合的各种因素进行了系统研究. 结果表明, 变形温度、应变速率、摩擦系数、试样尺寸和孔洞尺寸对锻造过程中孔洞的闭合基本没有影响, 而试样高径比、孔洞位置和孔洞形状对孔洞的闭合有较大影响. 其中试样高径比和孔洞位置通过影响孔洞周围的应变条件来影响孔洞闭合, 是间接因素. 孔洞所在位置的应变越大, 孔洞越容易闭合. 孔洞形状是影响孔洞闭合的直接因素, 也是最本质的因素. 为了描述这种现象, 提出了孔洞高径比的概念. 模拟结果显示, 沿变形方向孔洞的高径比越大,孔洞越难闭合. 基于以上研究和大钢锭的实际解剖结果, 提出了全新的宽砧径向压实工艺(WRF法). 该工艺可使应变集中于钢锭中心区域, 并满足孔洞闭合所需的最佳高径比条件, 因此, 可高效愈合钢锭的中心缩孔、疏松. 工业实验验证了该工艺的有效性和实用性.

关键词 ：孔洞闭合, 孔洞高径比, 宽砧径向压实法

Abstract：

All the parameters that may affect void closure behavior are judged using finite element method (FEM). The simulation results show that temperature, strain rate, friction coefficient, sample size and void size do not affect the void closure behavior. Height–diameter ratio of the sample and void position will affect the strain around the void and the void will be easier to close when the strain around it are higher. Of all the parameters, void shape is the most important one. Height–diameter ratio of the void is defined to describe the effect of void shape. The simulation results show that the larger height–diameter ratio of the void, the harder it is for the void to close. Based on these results and the sectioning results of a 100 t ingot, a new forging method, wide–anvil radial forging (WRF) is proposed. WRF method can concentrate the strain on the center of the ingot; meet the optimum height–diameter ratio condition of the void closure and heal shrinkage cavities effectively. Experiments on continuous casting billets prove the effectiveness and applicability of this method

Key words： void closure height–diameter ratio of void wide–anvil radial forging (WRF) method

收稿日期: 2012-06-08

ZTFLH:

TG316

基金资助:

国家自然科学基金资助项目51204157

作者简介: 徐斌, 男, 1984年生, 博士生

	服务

	把本文推荐给朋友
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	徐斌孙明月李殿中
44.8K

链接本文:

https://www.ams.org.cn/CN/10.3724/SP.J.1037.2012.00339 或 https://www.ams.org.cn/CN/Y2012/V48/I10/1194

[1] Campbell J, translated by Li D Z, Li Y Y. Castings. 2nd Ed., Beijing: Science Press, 2011: 240

(Campbell J著, 李殿中, 李依依译. 铸造原理. 第2版, 北京: 科学出版社, 2011: 240)

[2] Li S J, Sun M Y, Liu H W, Li D Z. Acta Metall Sin, 2011; 47: 946

(李世键, 孙明月, 刘宏伟, 李殿中. 金属学报, 2011; 47: 946)

[3] Park C Y, Yang D Y. J Mater Process Technol, 1996; 57: 129

[4] Park C Y, Yang D Y. J Mater Process Technol, 1997; 72: 32

[5] Ma Q X, Zhong Y X, Cao Q X. J Tsinghua Univ (Sci Technol), 1999; 39(11): 94

(马庆贤, 钟约先, 曹起骧. 清华大学学报(自然科学版), 1999; 39(11): 94)

[6] Li S J. PhD Thesis, Institute of Metal Research, Chinese Academy of Sciences, Shenyang, 2011

(李世键. 中国科学院金属研究所博士学位论文, 沈阳, 2011)

[7] Wang Z T, Liu Z, Ren M. Chin J Mech Eng, 1989; 25(3): 51

(王祖唐, 刘庄, 任猛. 机械工程学报, 1989; 25(3): 51)

[8] Wang Z T, Liu Z, Ren M. Chin J Mech Eng, 1989; 25(4): 47

(王祖唐, 刘庄, 任猛. 机械工程学报, 1989; 25(4): 47)

[9] Wang A, Thomson P F, Hodgson P D. J Mater Process Technol, 1996; 60: 95

[10] Kopp R, Ambaum E. Stahl Eisen, 1976; 96: 1004

[11] Kopp R, Stenzhorn P. Stahl Eisen, 1983; 103: 377

[12] Ono S, Minami K, Ochiai T, Iwadate T, Nakata S. Japan Soc Mech Eng, 1995; 61(585): 387

[13] Park C Y, Yang D Y. J Mater Process Technol, 1997; 67: 195

[14] Ren G S, Huang Z H, Bai Z B. Chin J Mech Eng, 1995; 31(2): 93

(任广升, 黄朝晖, 白志斌. 机械工程学报, 1995; 31(2): 93)

[15] Han J T, Zhao G, Cao Q X. Acta Metall Sin, 1996; 32: 723

(韩静涛, 赵钢, 曹起骧. 金属学报, 1996; 32: 723)

[16] Lee Y S, Lee S U, VanTyne C J, Joo B D, Moon Y H. J Mater Process Technol, 2011; 211: 1136

[17] Kakimoto H, Arikawa T, Takahashi Y, Tanaka T, Imaida Y. J Mater Process Technol, 2010; 210: 415

[18] Banaszek G, Stefanik A. J Mater Process Technol, 2006; 177: 238

[19] Zhang X X, Cui Z S, Chen W, Li Y. J Mater Process Technol, 2009; 209: 1950

[20] Kang D T, Ye G B. Materials and Heat Treatment of Large Forgings. Beijing: Longmen Bookstore, 1998: 73

(康大韬, 叶国斌. 大型锻件材料及热处理. 北京: 龙门书局, 1998: 73)

[21] Wang L G, Huang Y, Liu Z B. J Plast Eng, 2002; 9(2): 28

(王雷刚, 黄瑶, 刘助柏. 塑性工程学报, 2002; 9(2): 28)

[22] Chun M S, Van Tyne C J, Moon Y H. Steel Res Int, 2006; 77: 116

[23] Dudra S P, Im Y T. Int J Mach Tools Manufact, 1990; 30: 65

[24] Kim Y D, Cho J R, Bae W B. J Mater Process Technol, 2011; 211: 1005

[25] Cui Z S, Ren G S, Xu B Y, Xu C G, Liu G H. J Tsinghua Univ (Sci Technol), 2003; 43(2): 227

(崔振山, 任广升, 徐秉业, 徐春国, 刘桂华. 清华大学学报(自然科学版), 2003; 43(2): 227)

[26] Liu Z B, Ni L Y, Liang C, Liu G H, Deng D M. Chin Mech Eng, 2005; 16(1): 74

(刘助柏, 倪利勇, 梁晨, 刘国晖, 邓冬梅. 中国机械工程, 2005; 16(1): 74)

[1]	李殿中, 马璇, 徐斌, 孙明月. 高效愈合钢锭内部缺陷的锻造工艺设计^*[J]. 金属学报, 2016, 52(10): 1199-1206.

Viewed

Full text

Abstract

Cited

Shared

Discussed